Hardware Programming Guide for DSI PHY says that PLL_SHUTDOWNB and
DIGTOP_PWRDN_B have to be asserted for any PLL register access.
Whenever dsi_pll_7nm_vco_recalc_rate() or dsi_pll_7nm_vco_set_rate()
were called on unprepared PLL, driver read values of zero leading to all
sort of further troubles, like failing to set pixel and byte clock
rates.
Asserting the PLL shutdown bit is done by dsi_pll_enable_pll_bias() (and
corresponding dsi_pll_disable_pll_bias()) which are called through the
code, including from PLL .prepare() and .unprepare() callbacks.
The .set_rate() and .recalc_rate() can be called almost anytime from
external users including times when PLL is or is not prepared, thus
driver should not interfere with the prepare status.
Implement simple reference counting for the PLL bias, so
set_rate/recalc_rate will not change the status of prepared PLL.
Issue of reading 0 in .recalc_rate() did not show up on existing
devices, but only after re-ordering the code for SM8750.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673416/
Link: https://lore.kernel.org/r/20250908094950.72877-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Driver unconditionally saves current state on first init in
dsi_pll_7nm_init(), but does not save the VCO rate, only some of the
divider registers. The state is then restored during probe/enable via
msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() ->
dsi_7nm_pll_restore_state().
Restoring calls dsi_pll_7nm_vco_set_rate() with
pll_7nm->vco_current_rate=0, which basically overwrites existing rate of
VCO and messes with clock hierarchy, by setting frequency to 0 to clock
tree. This makes anyway little sense - VCO rate was not saved, so
should not be restored.
If PLL was not configured configure it to minimum rate to avoid glitches
and configuring entire in clock hierarchy to 0 Hz.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/657827/
Link: https://lore.kernel.org/r/20250610-b4-sm8750-display-v6-9-ee633e3ddbff@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
According to Hardware Programming Guide for DSI PHY, the retime buffer
resync should be done after PLL clock users (byte_clk and intf_byte_clk)
are enabled. Downstream also does it as part of configuring the PLL.
Driver was only turning off the resync FIFO buffer, but never bringing it
on again.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/657823/
Link: https://lore.kernel.org/r/20250610-b4-sm8750-display-v6-6-ee633e3ddbff@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667874/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-5-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667872/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-4-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667870/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-3-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667869/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-2-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667866/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-1-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
To configure and enable the DSI PHY PLL clocks, the MDSS AHB clock must
be active for MMIO operations. Typically, this AHB clock is enabled as
part of the DSI PHY interface enabling (dsi_phy_enable_resource).
However, since these PLL clocks are registered as clock entities, they
can be enabled independently of the DSI PHY interface, leading to
enabling failures and subsequent warnings:
```
msm_dsi_phy 5e94400.phy: [drm:dsi_pll_14nm_vco_prepare] *ERROR* DSI PLL lock failed
------------[ cut here ]------------
dsi0pllbyte already disabled
WARNING: CPU: 3 PID: 1 at drivers/clk/clk.c:1194 clk_core_disable+0xa4/0xac
CPU: 3 UID: 0 PID: 1 Comm: swapper/0 Tainted:
Tainted: [W]=WARN
Hardware name: Qualcomm Technologies, Inc. Robotics RB1 (DT)
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[...]
```
This issue is particularly prevalent at boot time during the disabling of
unused clocks (clk_disable_unused()) which includes enabling the parent
clock(s) when CLK_OPS_PARENT_ENABLE flag is set (this is the case for the
14nm DSI PHY PLL consumers).
To resolve this issue, we move the AHB clock as a PM dependency of the DSI
PHY device (via pm_clk). Since the DSI PHY device is the parent of the PLL
clocks, this resolves the PLL/AHB dependency. Now the AHB clock is enabled
prior the PLL clk_prepare callback, as part of the runtime-resume chain.
We also eliminate dsi_phy_[enable|disable]_resource functions, which are
superseded by runtime PM.
Note that it breaks compatibility with kernels before 6.0, as we do not
support anymore the legacy `iface_clk` name.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/663239/
Link: https://lore.kernel.org/r/20250709140836.124143-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Add support for DSI PHY v7.0 on Qualcomm SM8750 SoC which comes with an
incompatible hardware interface change:
ICODE_ACCUM_STATUS_LOW and ALOG_OBSV_BUS_STATUS_1 registers - their
offsets were just switched. Currently these registers are not used in
the driver, so the easiest is to document both but keep them commented
out to avoid conflict.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/659616/
Link: https://lore.kernel.org/r/20250618-b4-sm8750-display-v7-6-a591c609743d@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Driver unconditionally saves current state on first init in
dsi_pll_10nm_init(), but does not save the VCO rate, only some of the
divider registers. The state is then restored during probe/enable via
msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() ->
dsi_10nm_pll_restore_state().
Restoring calls dsi_pll_10nm_vco_set_rate() with
pll_10nm->vco_current_rate=0, which basically overwrites existing rate of
VCO and messes with clock hierarchy, by setting frequency to 0 to clock
tree. This makes anyway little sense - VCO rate was not saved, so
should not be restored.
If PLL was not configured configure it to minimum rate to avoid glitches
and configuring entire in clock hierarchy to 0 Hz.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/sz4kbwy5nwsebgf64ia7uq4ee7wbsa5uy3xmlqwcstsbntzcov@ew3dcyjdzmi2/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Fixes: a4ccc37693 ("drm/msm/dsi_pll_10nm: restore VCO rate during
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/654796/
Link: https://lore.kernel.org/r/20250520111325.92352-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Newly added dsi_pll_cmn_clk_cfg1_update() wrapper protects concurrent
updates to PHY_CMN_CLK_CFG1 register between driver and Common Clock
Framework. pll_7nm_register() still used in one place previous
readl+writel, which can be simplified with this new wrapper.
This is purely for readability and simplification and should have no
functional impact, because the code touched here is before clock is
registered via CCF, so there is no concurrency issue.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/638323/
Link: https://lore.kernel.org/r/20250219-drm-msm-phy-pll-cfg-reg-v5-1-d28973fa513a@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Since SM8250 all downstream sources program clock inverters in
PLL_CLOCK_INVERTERS_1 register and leave the PLL_CLOCK_INVERTERS as
reset value (0x0). The most recent Hardware Programming Guide for 3 nm,
4 nm, 5 nm and 7 nm PHYs also mention PLL_CLOCK_INVERTERS_1.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/634489/
Link: https://lore.kernel.org/r/20250129115504.40080-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
PHY_CMN_CLK_CFG1 register has four fields being used in the driver: DSI
clock divider, source of bitclk and two for enabling the DSI PHY PLL
clocks.
dsi_7nm_set_usecase() sets only the source of bitclk, so should leave
all other bits untouched. Use newly introduced
dsi_pll_cmn_clk_cfg1_update() to update respective bits without
overwriting the rest.
While shuffling the code, define and use PHY_CMN_CLK_CFG1 bitfields to
make the code more readable and obvious.
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/637380/
Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-3-0943b850722c@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
PHY_CMN_CLK_CFG1 register is updated by the PHY driver and by a mux
clock from Common Clock Framework:
devm_clk_hw_register_mux_parent_hws(). There could be a path leading to
concurrent and conflicting updates between PHY driver and clock
framework, e.g. changing the mux and enabling PLL clocks.
Add dedicated spinlock to be sure all PHY_CMN_CLK_CFG1 updates are
synchronized.
While shuffling the code, define and use PHY_CMN_CLK_CFG1 bitfields to
make the code more readable and obvious.
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/637378/
Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-2-0943b850722c@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
PHY_CMN_CLK_CFG0 register is updated by the PHY driver and by two
divider clocks from Common Clock Framework:
devm_clk_hw_register_divider_parent_hw(). Concurrent access by the
clocks side is protected with spinlock, however driver's side in
restoring state is not. Restoring state is called from
msm_dsi_phy_enable(), so there could be a path leading to concurrent and
conflicting updates with clock framework.
Add missing lock usage on the PHY driver side, encapsulated in its own
function so the code will be still readable.
While shuffling the code, define and use PHY_CMN_CLK_CFG0 bitfields to
make the code more readable and obvious.
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/637376/
Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-1-0943b850722c@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Add phy configuration for 28nm dsi phy found on MSM8937 SoC. Only
difference from existing msm8916 configuration is number of phy
and io_start addresses.
Signed-off-by: Daniil Titov <daniilt971@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Barnabás Czémán <trabarni@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/600518/
Link: https://lore.kernel.org/r/20240623-dsi-v2-4-a0ca70fb4846@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This helper has been introduced to avoid programmer errors (missing
_put calls leading to dangling refcnt) when using pm_runtime_get, use it.
While at it, start checking the return value.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 5c82902844 ("drm/msm/dsi: Split PHY drivers to separate files")
Patchwork: https://patchwork.freedesktop.org/patch/543350/
Link: https://lore.kernel.org/r/20230620-topic-dsiphy_rpm-v2-1-a11a751f34f0@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SM6125 features only a single PHY (despite a secondary PHY PLL source
being available to the disp_cc_mdss_pclk0_clk_src clock), and downstream
sources for this "trinket" SoC do not define the typical "vcca"
regulator to be available nor used. This, including the register offset
is identical to QCM2290, whose config struct can trivially be reused.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/548980/
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-13-a3f287dd6c07@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The regulator setup was likely copied from other SoCs by mistake. Just
like SM6125 the DSI PHY on this platform is not getting power from a
regulator but from the MX power domain.
Fixes: 572e9fd6d1 ("drm/msm/dsi: Add phy configuration for QCM2290")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/548959/
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-1-a3f287dd6c07@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
MSM8226 uses a modified PLL lock sequence compared to MSM8974, which is
based on the function dsi_pll_enable_seq_m in the msm-3.10 kernel.
Worth noting that the msm-3.10 downstream kernel also will try other
sequences in case this one doesn't work, but during testing it has shown
that the _m sequence succeeds first time also:
.pll_enable_seqs[0] = dsi_pll_enable_seq_m,
.pll_enable_seqs[1] = dsi_pll_enable_seq_m,
.pll_enable_seqs[2] = dsi_pll_enable_seq_d,
.pll_enable_seqs[3] = dsi_pll_enable_seq_d,
.pll_enable_seqs[4] = dsi_pll_enable_seq_f1,
.pll_enable_seqs[5] = dsi_pll_enable_seq_c,
.pll_enable_seqs[6] = dsi_pll_enable_seq_e,
We may need to expand this in the future.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/540618/
Link: https://lore.kernel.org/r/20230308-msm8226-mdp-v3-6-b6284145d67a@z3ntu.xyz
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
If the dispcc uses CLK_OPS_PARENT_ENABLE (e.g. on QCM2290), CCF can try
enabling VCO before the rate has been programmed. This can cause clock
lockups and/or other boot issues. Program the VCO to the minimal PLL
rate if the read rate is 0 Hz.
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reported-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Fixes: f079f6d999 ("drm/msm/dsi: Add PHY/PLL for 8x96")
Patchwork: https://patchwork.freedesktop.org/patch/534813/
Link: https://lore.kernel.org/r/20230501011257.3460103-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
According to the vendor kernel, byte intf clock rate should be a half of
the byte clock only when DSI PHY version is above 2.0 (in other words,
10nm PHYs and later) and only if PHY is used in D-PHY mode. Currently
MSM DSI code handles only the second part of the clause (C-PHY vs
D-PHY), skipping DSI PHY version check, which causes issues on some of
14nm DSI PHY platforms (e.g. qcm2290).
Move divisor selection to DSI PHY code, pass selected divisor through
shared timings and set byte intf clock rate accordingly.
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # SM6115P J606F
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/519006/
Link: https://lore.kernel.org/r/20230118130027.2345719-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In preparation to adding the sm8350 and sm8450 PHYs support, rearrange
register values calculations in dsi_7nm_phy_enable(). This change bears
no functional changes itself, it is merely a preparation for the next
patch.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514232/
Link: https://lore.kernel.org/r/20221207012231.112059-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The QCM2290 SoC a the 14nm (V2.0) single DSI phy. The platform is not
fully compatible with the standard 14nm PHY, so it requires a separate
compatible and config entry.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[DB: rebased and updated commit msg]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/504578/
Link: https://lore.kernel.org/r/20220924121900.222711-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The dsi_phy_driver_probe() function has a "goto fail" for no
reason. Change it to just always return directly when it sees an
error. Make this simpler by leveraging dev_err_probe() which is
designed to make code like this shorter / simpler.
NOTE: as part of this, we now pass through error codes directly from
msm_ioremap_size() rather than translating to -ENOMEM. This changed
mostly because it's much more convenient when using dev_err_probe()
and also it's usually encouraged not to hide error codes like the old
code was doing unless there is a good reason. I can't see any reason
why we'd need to return -ENOMEM instead of -EINVAL from the probe
function.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496324/
Link: https://lore.kernel.org/r/20220804073608.v4.6.I969118a35934a0e5007fe4f80e3e28e9c0b7602a@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of the commit 1de452a0ed ("regulator: core: Allow drivers to
define their init data as const") we no longer need to do copying of
regulator bulk data from initdata to something dynamic. Let's take
advantage of that.
In addition to saving some code, this also moves us to using
ARRAY_SIZE() to specify how many regulators we have which is less
error prone.
This gets rid of some layers of wrappers which makes it obvious that
we can get rid of an extra error print.
devm_regulator_bulk_get_const() prints errors for you so you don't
need an extra layer of printing.
In all cases here I have preserved the old settings without any
investigation about whether the loads being set are sensible. In the
cases of some of the PHYs if several PHYs in the same file used
exactly the same settings I had them point to the same data structure.
NOTE: Though I haven't done the math, this is likely an overall
savings in terms of "static const" data. We previously always
allocated space for 8 supplies. Each of these supplies took up 36
bytes of data (32 for name, 4 for an int).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496325/
Link: https://lore.kernel.org/r/20220804073608.v4.5.I55a9e65cb1c22221316629e98768ff473f47a067@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of commit 6eabfc018e ("regulator: core: Allow specifying an
initial load w/ the bulk API") we can now specify the initial load in
the bulk data rather than having to manually call regulator_set_load()
on each regulator. Let's use it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496319/
Link: https://lore.kernel.org/r/20220804073608.v4.4.I7b3c72949883846badb073cfeae985c55239da1d@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of commit 5451781dad ("regulator: core: Only count load for
enabled consumers"), a load isn't counted for a disabled
regulator. That means all the code in the DSI driver to specify and
set loads before disabling a regulator is not actually doing anything
useful. Let's remove it.
It should be noted that all of the loads set that were being specified
were pointless noise anyway. The only use for this number is to pick
between low power and high power modes of regulators. Regulators
appear to do this changeover at loads on the order of 10000 uA. You
would need a lot of clients of the same rail for that 100 uA number to
count for anything.
Note that now that we get rid of the setting of the load at disable
time, we can just set the load once when we first get the regulator
and then forget it.
It should also be noted that the regulator functions
regulator_bulk_enable() and regulator_set_load() already print error
messages when they encounter problems so while moving things around we
get rid of some extra error prints.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496320/
Link: https://lore.kernel.org/r/20220804073608.v4.3.If1f94fbbdb7c1d0fb3961de61483a851ad1971a7@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491927/
Link: https://lore.kernel.org/r/20220629225331.357308-12-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491923/
Link: https://lore.kernel.org/r/20220629225331.357308-11-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491921/
Link: https://lore.kernel.org/r/20220629225331.357308-10-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491925/
Link: https://lore.kernel.org/r/20220629225331.357308-9-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Krzysztof Kozlowski