The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
The Rockchip PCIe PHY driver, used on the RK3399, has its own definition
of HIWORD_UPDATE.
Remove it, and replace instances of it with hw_bitfield.h's
FIELD_PREP_WM16. To achieve this, some mask defines are reshuffled, as
FIELD_PREP_WM16 uses the mask as both the mask of bits to write and to
derive the shift amount from in order to shift the value.
In order to ensure that the mask is always a constant, the inst->index
shift is performed after the FIELD_PREP_WM16, as this is a runtime
value.
>From this, we gain compile-time error checking, and in my humble opinion
nicer code, as well as a single definition of this macro across the
entire codebase to aid in code comprehension.
Tested on a RK3399 ROCKPro64, where PCIe still works as expected when
accessing an NVMe drive.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
Remove this driver's HIWORD_UPDATE macro, and replace all instances of
it with (hopefully) equivalent FIELD_PREP_WM16 instances. To do this, a
few of the defines are being adjusted, as FIELD_PREP_WM16 shifts up the
value for us. This gets rid of the icky update(mask, mask) shenanigans.
The benefit of using FIELD_PREP_WM16 is that it does more checking of
the input, hopefully catching errors. In practice, a shared definition
makes code more readable than several different flavours of the same
macro, and the shifted value helps as well.
I do not have the hardware that uses this particular driver, so it's
compile-tested only as far as my own testing goes.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
phy-rockchip-samsung-dcphy is actually an exemplary example, where the
similarities to FIELD_PREP were spotted and the driver local macro has
the same semantics as the new FIELD_PREP_WM16 hw_bitfield.h macro.
Still, get rid of FIELD_PREP_HIWORD now that a shared implementation
exists, replacing the two instances of it with FIELD_PREP_WM16. This
gives us slightly better error checking; the value is now checked to fit
in 16 bits.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
Replace the implementation of the rockchip eMMC PHY driver's
HIWORD_UPDATE macro with hw_bitfield.h's FIELD_PREP_WM16. This makes the
change more easily reviewable.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
Commit 0cc22f5a86 ("phy: qcom: qmp-pcie: Add PHY register retention
support") added support for using the "no_csr" reset to skip configuration
of the PHY if the init sequence was already applied by the boot firmware.
The expectation is that the PHY is only turned on/off by using the "no_csr"
reset, instead of powering it down and re-programming it after a full
reset.
The boot firmware on X1E does not fully conform to this expectation: If the
PCIe3 link fails to come up (e.g. because no PCIe card is inserted), the
firmware powers down the PHY using the QPHY_PCS_POWER_DOWN_CONTROL
register. The QPHY_START_CTRL register is kept as-is, so the driver assumes
the PHY is already initialized and skips the configuration/power up
sequence. The PHY won't come up again without clearing the
QPHY_PCS_POWER_DOWN_CONTROL, so eventually initialization fails:
qcom-qmp-pcie-phy 1be0000.phy: phy initialization timed-out
phy phy-1be0000.phy.0: phy poweron failed --> -110
qcom-pcie 1bd0000.pcie: cannot initialize host
qcom-pcie 1bd0000.pcie: probe with driver qcom-pcie failed with error -110
This can be reliably reproduced on the X1E CRD, QCP and Devkit when no card
is inserted for PCIe3.
Fix this by checking the QPHY_PCS_POWER_DOWN_CONTROL register in addition
to QPHY_START_CTRL. If the PHY is powered down with the register, it
doesn't conform to the expectations for using the "no_csr" reset, so we
fully re-initialize with the normal reset sequence.
Also check the register more carefully to ensure all of the bits we expect
are actually set. A simple !!(readl()) is not enough, because the PHY might
be only partially set up with some of the expected bits set.
Cc: stable@vger.kernel.org
Fixes: 0cc22f5a86 ("phy: qcom: qmp-pcie: Add PHY register retention support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250821-phy-qcom-qmp-pcie-nocsr-fix-v3-1-4898db0cc07c@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some SoCs are just validated with the TX delay enabled. With commit
ca13b249f2 ("net: ethernet: ti: am65-cpsw: fixup PHY mode for fixed
RGMII TX delay"), the network driver will patch the delay setting on the
fly assuming that the TX delay setting is fixed. In reality, the TX
delay is configurable and just skipped in the documentation. There are
bootloaders, which will disable the TX delay and this will lead to a
transmit path which doesn't add any delays at all.
Fix that by always writing the RGMII_ID setting and report an error for
unsupported RGMII delay modes.
This is safe to do and shouldn't break any boards in mainline because
the fixed delay is only introduced for gmii-sel compatibles which are
used together with the am65-cpsw-nuss driver and also contains the
commit above.
Fixes: ca13b249f2 ("net: ethernet: ti: am65-cpsw: fixup PHY mode for fixed RGMII TX delay")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://lore.kernel.org/r/20250819065622.1019537-1-mwalle@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make sure to drop the reference to the control device taken by
of_find_device_by_node() during probe when the driver is unbound.
Fixes: 918ee0d21b ("usb: phy: omap-usb3: Don't use omap_get_control_dev()")
Cc: stable@vger.kernel.org # 3.13
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724131206.2211-4-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make sure to drop the reference to the control device taken by
of_find_device_by_node() during probe when the driver is unbound.
Fixes: 478b6c7436 ("usb: phy: omap-usb2: Don't use omap_get_control_dev()")
Cc: stable@vger.kernel.org # 3.13
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724131206.2211-3-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make sure to drop the references taken to the PMC OF node and device by
of_parse_phandle() and of_find_device_by_node() during probe.
Note the holding a reference to the PMC device does not prevent the
PMC regmap from going away (e.g. if the PMC driver is unbound) so there
is no need to keep the reference.
Fixes: 2d10214872 ("phy: tegra: xusb: Add wake/sleepwalk for Tegra210")
Cc: stable@vger.kernel.org # 5.14
Cc: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250724131206.2211-2-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current configuration used for the IPQ5332 M31 USB PHY fails the
Near End High Speed Signal Quality compliance test. To resolve this,
update the initialization sequence as specified in the Hardware Design
Document.
Fixes: 08e49af507 ("phy: qcom: Introduce M31 USB PHY driver")
Cc: stable@kernel.org
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250630-ipq5332_hsphy_complaince-v2-1-63621439ebdb@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the cam0 sysreg property name (samsung,cam0-sysreg), which has been
erroneously declared as samsung,cam-sysreg. This follows the same name
used in Exynos5433 PHY.
Fixes: 543f5e3142 ("phy: exynos-mipi-video: introduce support for exynos7870")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://lore.kernel.org/r/20250710-exynos7870-mipi-phy-fix-v2-1-5cf50d69c9d7@disroot.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As per a commit from Qualcomm's downstream 6.1 kernel[0], the init
sequence is missing setting the CMN_CTRL_OVERRIDE_EN bit back to 0 at
the end, as per the 'latest' HPG revision (as of November 2023).
[0] b77774a89e
Fixes: 80090810f5 ("phy: qcom: Add QCOM SNPS eUSB2 driver")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20250715-sm7635-eusb-phy-v3-3-6c3224085eb6@fairphone.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
pcie_conf is used to touch TEST_WRITE strobe signal. This signal should
be enabled, a little time waited, and then disabled. Current code clearly
was copy-pasted and never disables the strobe signal. Adjust the define.
While at it, remove PHY_CFG_RD_MASK which has been unused since
64cdc03608 ("phy: rockchip-pcie: remove unused phy_rd_cfg function").
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/d514d5d5627680caafa8b7548cbdfee4307f5440.1751322015.git.geraldogabriel@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Current code enables only Lane 0 because pwr_cnt will be incremented on
first call to the function. Let's reorder the enablement code to enable
all 4 lanes through GRF.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Valmantas Paliksa <walmis@gmail.com>
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/16b610aab34e069fd31d9f57260c10df2a968f80.1751322015.git.geraldogabriel@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add missing DP PHY status and VCO clock configuration registers to fix
configuring the VCO rate on SM8750. Without proper VCO rate setting, it
works on after-reset half of rate which is not enough for DP over USB to
work as seen on logs:
[drm:msm_dp_ctrl_link_train_1_2] *ERROR* max v_level reached
[drm:msm_dp_ctrl_link_train_1_2] *ERROR* link training #1 on phy 0 failed. ret=-11
Fixes: c4364048ba ("phy: qcom: qmp-combo: Add new PHY sequences for SM8750")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250616062541.7167-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drivers should generally be quiet on successful probe so drop the
registration printk from the recently added M31 EUSB2 driver.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250617080401.11147-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The device_get_match_data() helper returns NULL if a new entry is ever
added without corresponding match data.
Fixes: 9c8504861c ("phy: qcom: Add M31 based eUSB2 PHY driver")
Cc: Wesley Cheng <quic_wcheng@quicinc.com>
Cc: Melody Olvera <melody.olvera@oss.qualcomm.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250617080503.11262-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update the PHY settings to align with the latest PCIe PHY
Hardware Programming Guide for both PCIe controllers on the
SA8775P platform.
Add the ln_shrd region for SA8775P, incorporating new register
writes as specified in the updated Hardware Programming Guide.
Update pcs table for QCS8300, since both QCS8300 and SA8775P are
closely related and share same pcs settings.
Signed-off-by: Mrinmay Sarkar <mrinmay.sarkar@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250617-update_phy-v5-1-2df83ed6a373@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Zeroing out registers does not happen in the downstream kernel, and will
"tune" the repeater in surely unexpected ways since most registers don't
have a reset value of 0x0.
Stop doing that and instead just set the registers that are in the init
sequence (though long term I don't think there's actually PMIC-specific
init sequences, there's board specific tuning, but that's a story for
another day).
Fixes: 99a517a582 ("phy: qualcomm: phy-qcom-eusb2-repeater: Zero out untouched tuning regs")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250617-eusb2-repeater-tuning-v2-2-ed6c484f18ee@fairphone.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While it's true that, generally, the T-PHY V3 does not support the
slew calibration process, some minor versions of it actually do,
moreover, some SoCs may not support this even though the version
of the PHY IP does.
The reference clock and rate coefficient parameters are used only
for slew calibration: move those to platform data, then document
and change the checks in hs_slew_rate_calibrate() to perform the
calibration only if:
- EYE value was not supplied (pre-calculated calibration); and
- Slew reference clock value is present (not zero); and
- Slew coefficient is present (not zero).
Moreover, change the probe function to always check if both the
slew reference clock and coefficient properties are present and,
if not, assign the value from platform data (which, as reminder,
if not added means that it's zero!), instead of checking the PHY
IP version.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250623120315.109881-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As struct mtk_phy_pdata was almost fully documented, transfer
the comments into kerneldoc on top.
While at it, also rewrite the comments to both improve the writing
writing and the actual information in the documentation, and add a
description for the `version` member of the structure.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250623120315.109881-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
(devm_)power_supply_get_by_phandle now internally uses fwnode and are no
longer DT specific. Thus drop the ifdef check for CONFIG_OF and rename
to (devm_)power_supply_get_by_reference to avoid the DT terminology.
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250430-psy-core-convert-to-fwnode-v2-5-f9643b958677@collabora.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Drivers should generally be quiet on successful probe, but this is not
followed by some PHY drivers, for example:
snps-eusb2-hsphy 88e1000.phy: Registered Snps-eUSB2 phy
qcom-eusb2-repeater c432000.spmi:pmic@7:phy@fd00: Registered Qcom-eUSB2 repeater
qcom-eusb2-repeater c432000.spmi:pmic@a:phy@fd00: Registered Qcom-eUSB2 repeater
qcom-eusb2-repeater c432000.spmi:pmic@b:phy@fd00: Registered Qcom-eUSB2 repeater
snps-eusb2-hsphy fd3000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy fd9000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy fde000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy 88e0000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy 88e2000.phy: Registered Snps-eUSB2 phy
Drop (or demote to debug level) unnecessary registration info messages
to make boot logs a little less noisy.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250523085112.11287-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add register sequences and support for PCIe multilink + USB configuration
for 100MHz reference clock. The same SSC is used for both PCIe and USB.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Co-developed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20250616064705.3225758-3-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use a more common format for the id table sentinel for consistency and
symmetry.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250523084839.11015-8-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is already a loop index variable declared at function scope so
drop the unnecessary overloaded loop declarations.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250523084839.11015-7-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The devm_of_phy_optional_get() takes an optional name argument as its
third parameter and not an index like the recently replaced
devm_of_phy_get_by_index().
Replace 0 with an explicit NULL for consistency and readability.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250523084839.11015-6-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clean up the error messages by using a consistent format with a colon
followed by a space and an errno (or unsupported frequency).
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250523084839.11015-5-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rename the clock error label which is now used to disable all clocks and
not just the ref clock on phy_init() errors.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250523084839.11015-4-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make sure to disable the repeater PHY also on phy_init() failure.
Fixes: 3584f6392f ("phy: qcom: phy-qcom-snps-eusb2: Add support for eUSB2 repeater")
Cc: Abel Vesa <abel.vesa@linaro.org>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250523084839.11015-3-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make sure to disable all clocks enabled at phy_init() also on
phy_exit().
Fixes: c4098f3e61 ("phy: phy-snps-eusb2: add support for exynos2200")
Cc: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250523084839.11015-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SM8750 utilizes an eUSB2 PHY from M31. Add the initialization
sequences to bring it out of reset and into an operational state. This
differs to the M31 USB driver, in that the M31 eUSB2 driver will
require a connection to an eUSB2 repeater. This PHY driver will handle
the initialization of the associated eUSB2 repeater when required.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Melody Olvera <melody.olvera@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250527-sm8750_usb_master-v6-6-d58de3b41d34@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The eUSB2 repeater that exists in the QCOM PMICs are utilized for several
different eUSB2 PHY vendors, such as M31 or Synopsys. Hence, the wording
needs to be updated to remove associations to a specific vendor.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Melody Olvera <melody.olvera@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250527-sm8750_usb_master-v6-5-d58de3b41d34@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add new register offsets and PHY values for SM8750. Some of the previous
definitions can be leveraged from older PHY versions as offsets within
registers have not changed. This also adds the required PHY sequence that
is recommended after running hardware characterization.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Melody Olvera <melody.olvera@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250527-sm8750_usb_master-v6-4-d58de3b41d34@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If the PHY driver uses another PHY internally (e.g. in case of eUSB2,
repeaters are represented as PHYs), then it would trigger the following
lockdep splat because all PHYs use a single static lockdep key and thus
lockdep can not identify whether there is a dependency or not and
reports a false positive.
Make PHY subsystem use dynamic lockdep keys, assigning each driver a
separate key. This way lockdep can correctly identify dependency graph
between mutexes.
============================================
WARNING: possible recursive locking detected
6.15.0-rc7-next-20250522-12896-g3932f283970c #3455 Not tainted
--------------------------------------------
kworker/u51:0/78 is trying to acquire lock:
ffff0008116554f0 (&phy->mutex){+.+.}-{4:4}, at: phy_init+0x4c/0x12c
but task is already holding lock:
ffff000813c10cf0 (&phy->mutex){+.+.}-{4:4}, at: phy_init+0x4c/0x12c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&phy->mutex);
lock(&phy->mutex);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by kworker/u51:0/78:
#0: ffff000800010948 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x18c/0x5ec
#1: ffff80008036bdb0 (deferred_probe_work){+.+.}-{0:0}, at: process_one_work+0x1b4/0x5ec
#2: ffff0008094ac8f8 (&dev->mutex){....}-{4:4}, at: __device_attach+0x38/0x188
#3: ffff000813c10cf0 (&phy->mutex){+.+.}-{4:4}, at: phy_init+0x4c/0x12c
stack backtrace:
CPU: 0 UID: 0 PID: 78 Comm: kworker/u51:0 Not tainted 6.15.0-rc7-next-20250522-12896-g3932f283970c #3455 PREEMPT
Hardware name: Qualcomm CRD, BIOS 6.0.240904.BOOT.MXF.2.4-00528.1-HAMOA-1 09/ 4/2024
Workqueue: events_unbound deferred_probe_work_func
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x90/0xd0
dump_stack+0x18/0x24
print_deadlock_bug+0x258/0x348
__lock_acquire+0x10fc/0x1f84
lock_acquire+0x1c8/0x338
__mutex_lock+0xb8/0x59c
mutex_lock_nested+0x24/0x30
phy_init+0x4c/0x12c
snps_eusb2_hsphy_init+0x54/0x1a0
phy_init+0xe0/0x12c
dwc3_core_init+0x450/0x10b4
dwc3_core_probe+0xce4/0x15fc
dwc3_probe+0x64/0xb0
platform_probe+0x68/0xc4
really_probe+0xbc/0x298
__driver_probe_device+0x78/0x12c
driver_probe_device+0x3c/0x160
__device_attach_driver+0xb8/0x138
bus_for_each_drv+0x84/0xe0
__device_attach+0x9c/0x188
device_initial_probe+0x14/0x20
bus_probe_device+0xac/0xb0
deferred_probe_work_func+0x8c/0xc8
process_one_work+0x208/0x5ec
worker_thread+0x1c0/0x368
kthread+0x14c/0x20c
ret_from_fork+0x10/0x20
Fixes: 3584f6392f ("phy: qcom: phy-qcom-snps-eusb2: Add support for eUSB2 repeater")
Fixes: e2463559ff ("phy: amlogic: Add Amlogic AXG PCIE PHY Driver")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reported-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/lkml/ZnpoAVGJMG4Zu-Jw@hovoldconsulting.com/
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250605-phy-subinit-v3-1-1e1e849e10cd@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In qmp_ufs_power_off, the PHY is already powered down by asserting
QPHY_PCS_POWER_DOWN_CONTROL. Therefore, additional phy_reset and
stopping SerDes are unnecessary. Also this approach does not
align with the phy HW programming guide.
Thus, refactor qmp_ufs_power_off to remove the phy_reset and stop
SerDes calls to simplify the code and ensure alignment with the PHY
HW programming guide.
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250526153821.7918-10-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
qmp_ufs_exit() is a wrapper function. It only calls qmp_ufs_com_exit().
Remove it to simplify the ufs phy driver.
Additonally partial Inline(dropping the reset assert) qmp_ufs_com_exit
into qmp_ufs_power_off function to avoid unnecessary function call
and to align with the Phy programming guide.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20250526153821.7918-9-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rename qmp_ufs_disable to qmp_ufs_power_off to better represent its
functionality. Additionally, inline qmp_ufs_exit into qmp_ufs_power_off
function to preserve the functionality of .power_off.
There is no functional change.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20250526153821.7918-8-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The qmp_ufs_power_on() function acts as a wrapper, solely invoking
qmp_ufs_com_init(). Additionally, the code within qmp_ufs_com_init()
does not correspond well with its name.
Therefore, to enhance the readability and eliminate unnecessary
function call inline qmp_ufs_com_init() into qmp_ufs_power_on().
There is no change to the functionality.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20250526153821.7918-7-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Refactor the UFS PHY reset handling to parse the reset logic only once
during initialization, instead of every resume.
As part of this change, move the UFS PHY reset parsing logic from
qmp_phy_power_on to the new qmp_ufs_phy_init function introduced
as part of phy_ops::init callback.
Co-developed-by: Ram Kumar Dwivedi <quic_rdwivedi@quicinc.com>
Signed-off-by: Ram Kumar Dwivedi <quic_rdwivedi@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250526153821.7918-6-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 052553af6a ("ufs/phy: qcom: Refactor to use phy_init call")
puts enabling regulators & clks, calibrating UFS PHY, starting serdes
and polling PCS ready status into phy_power_on.
In Current code regulators enable, clks enable, calibrating UFS PHY,
start_serdes and polling PCS_ready_status are part of phy_power_on.
UFS PHY registers are retained after power collapse, meaning calibrating
UFS PHY, start_serdes and polling PCS_ready_status can be done only when
hba is powered_on, and not needed every time when phy_power_on is called
during resume. Hence keep the code which enables PHY's regulators & clks
in phy_power_on and move the rest steps into phy_calibrate function.
Refactor the code to retain PHY regulators & clks in phy_power_on and
move out rest of the code to new phy_calibrate function.
Also move reset_control_assert to qmp_ufs_phy_calibrate to align
with Hardware programming guide.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20250526153821.7918-5-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Linus Torvalds