In case firmware has a bug and erroneously reports a status error
(e.g. device unusable) during boot, allow the user to tell the driver
to continue the boot regardless of the error status.
This will be done via kernel parameter which exposes a mask. The
user that loads the driver can decide exactly which status error to
ignore and which to take into account. The bitmask is according to
defines in hl_boot_if.h
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As F/ security indication must be available before driver approaches
PCI bus, F/W security should be derived from PCI id rather than be
fetched during boot handshake with F/W.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
For simplicity, use a single bringup flag indicating which FW
binaries should loaded to device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Because our graph contains network operations, we need to account
for delay in the network.
5 seconds timeout per CS is not enough to account for that.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We need to make sure our device is idle when rebooting a virtual
machine. This is done in the driver level.
The firmware will later handle FLR but we want to be extra safe and
stop the devices until the FLR is handled.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Driver must verify if HW is dirty before trying to fetch preboot
information. Hence, we move this validation to a prior stage of
the boot sequence.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The new state indicates that device should be reset in order
to re-gain funcionality.
This unique state can occur if reset_on_lockup is disabled
and an actual lockup has occurred.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In cases of multi-tenants, administrators may want to prevent data
leakage between users running on the same device one after another.
To do that the driver can scrub the internal memory (both SRAM and
DRAM) after a user finish to use the memory.
Because in GAUDI the driver allows only one application to use the
device at a time, it can scrub the memory when user app close FD.
In future devices where we have MMU on the DRAM, we can scrub the DRAM
memory with a finer granularity (page granularity) when the user
allocates the memory.
This feature is not supported in Goya.
To allow users that want to debug their applications, we add a kernel
module parameter to load the driver with this feature disabled.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The driver now loads the firmware in two stages. For debugging purposes
we need to support situations where only the first stage firmware is
loaded.
Therefore, use a bitmask to determine which F/W is loaded
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
driver will now get notified upon any PCI error occurred and
will respond according to the severity of the error.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
For internal needs of our CI we need to move all the common code into a
common folder instead of putting them in the root folder of the driver.
Same applies to the common header files under include/
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Oded Gabbay