Fixes for v6.14-rc4
Display:
* More catalog fixes:
- to skip watchdog programming through top block if its not present
- fix the setting of WB mask to ensure the WB input control is programmed
correctly through ping-pong
- drop lm_pair for sm6150 as that chipset does not have any 3dmerge block
* Fix the mode validation logic for DP/eDP to account for widebus (2ppc)
to allow high clock resolutions
* Fix to disable dither during encoder disable as otherwise this was
causing kms_writeback failure due to resource sharing between
* WB and DSI paths as DSI uses dither but WB does not
* Fixes for virtual planes, namely to drop extraneous return and fix
uninitialized variables
* Fix to avoid spill-over of DSC encoder block bits when programming
the bits-per-component
* Fixes in the DSI PHY to protect against concurrent access of
PHY_CMN_CLK_CFG regs between clock and display drivers
Core/GPU:
* Fix non-blocking fence wait incorrectly rounding up to 1 jiffy timeout
* Only print GMU fw version once, instead of each time the GPU resumes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtt2AODBXdod8ULXcAygf_qYvwRDVeUVtODx=2jErp6cA@mail.gmail.com
PHY_CMN_CLK_CFG1 register has four fields being used in the driver: DSI
clock divider, source of bitclk and two for enabling the DSI PHY PLL
clocks.
dsi_7nm_set_usecase() sets only the source of bitclk, so should leave
all other bits untouched. Use newly introduced
dsi_pll_cmn_clk_cfg1_update() to update respective bits without
overwriting the rest.
While shuffling the code, define and use PHY_CMN_CLK_CFG1 bitfields to
make the code more readable and obvious.
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/637380/
Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-3-0943b850722c@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
PHY_CMN_CLK_CFG1 register is updated by the PHY driver and by a mux
clock from Common Clock Framework:
devm_clk_hw_register_mux_parent_hws(). There could be a path leading to
concurrent and conflicting updates between PHY driver and clock
framework, e.g. changing the mux and enabling PLL clocks.
Add dedicated spinlock to be sure all PHY_CMN_CLK_CFG1 updates are
synchronized.
While shuffling the code, define and use PHY_CMN_CLK_CFG1 bitfields to
make the code more readable and obvious.
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/637378/
Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-2-0943b850722c@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
PHY_CMN_CLK_CFG0 register is updated by the PHY driver and by two
divider clocks from Common Clock Framework:
devm_clk_hw_register_divider_parent_hw(). Concurrent access by the
clocks side is protected with spinlock, however driver's side in
restoring state is not. Restoring state is called from
msm_dsi_phy_enable(), so there could be a path leading to concurrent and
conflicting updates with clock framework.
Add missing lock usage on the PHY driver side, encapsulated in its own
function so the code will be still readable.
While shuffling the code, define and use PHY_CMN_CLK_CFG0 bitfields to
make the code more readable and obvious.
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/637376/
Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-1-0943b850722c@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Updates for v6.14
MDSS:
- properly described UBWC registers
- added SM6150 (aka QCS615) support
MDP4:
- several small fixes
DPU:
- added SM6150 (aka QCS615) support
- enabled wide planes if virtual planes are enabled (by using two SSPPs for a single plane)
- fixed modes filtering for platforms w/o 3DMux
- fixed DSPP DSPP_2 / _3 links on several platforms
- corrected DSPP definitions on SDM670
- added CWB hardware blocks support
- added VBIF to DPU snapshots
- dropped struct dpu_rm_requirements
DP:
- reworked DP audio support
DSI:
- added SM6150 (aka QCS615) support
GPU:
- Print GMU core fw version
- GMU bandwidth voting for a740 and a750
- Expose uche trap base via uapi
- UAPI error reporting
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsutUu4ff6OpXNXxqf1xaV0rV6oV23VXNRiF0_OEfe72Q@mail.gmail.com
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241104190636.274926-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When (mode->clock * 1000) is larger than (1<<31), int to unsigned long
conversion will sign extend the int to 64 bits and the pclk_rate value
will be incorrect.
Fix this by making the result of the multiplication unsigned.
Note that above (1<<32) would still be broken and require more changes, but
its unlikely anyone will need that anytime soon.
Fixes: c4d8cfe516 ("drm/msm/dsi: add implementation for helper functions")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/618434/
Link: https://lore.kernel.org/r/20241007050157.26855-2-jonathan@marek.ca
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Add phy configuration for 28nm dsi phy found on MSM8937 SoC. Only
difference from existing msm8916 configuration is number of phy
and io_start addresses.
Signed-off-by: Daniil Titov <daniilt971@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Barnabás Czémán <trabarni@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/600518/
Link: https://lore.kernel.org/r/20240623-dsi-v2-4-a0ca70fb4846@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Allow board's device tree to specify the vsync source (aka TE source).
If the property is omitted, the display controller driver will use the
default setting.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
[DB: fixed clearing of return value if there is no TE property]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/598740/
Link: https://lore.kernel.org/r/20240613-dpu-handle-te-signal-v2-6-67a0116b5366@linaro.org
Make it clear why the pkt_per_line value is being "divided by 2".
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/596236/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-6-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Video mode DSC won't work if this field is not set correctly. Set it to fix
video mode DSC (for slice_per_pkt==1 cases at least).
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/596234/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-5-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The value returned by msm_dsi_wide_bus_enabled() doesn't match what the
driver is doing in video mode. Fix that by actually enabling widebus for
video mode.
Fixes: efcbd6f9cd ("drm/msm/dsi: Enable widebus for DSI")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Patchwork: https://patchwork.freedesktop.org/patch/596232/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-4-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
When dual-DSI (bonded DSI) was added in commit ed9976a09b
("drm/msm/dsi: adjust dsi timing for dual dsi mode") some DBG() prints
were not updated, leading to print the original mode->clock rather
than the adjusted (typically the mode clock divided by two, though more
recently also adjusted for DSC compression) msm_host->pixel_clk_rate
which is passed to clk_set_rate() just below. Fix that by printing the
actual pixel_clk_rate that is being set.
Fixes: ed9976a09b ("drm/msm/dsi: adjust dsi timing for dual dsi mode")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/589896/
Link: https://lore.kernel.org/r/20240417-drm-msm-initial-dualpipe-dsc-fixes-v1-1-78ae3ee9a697@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently the MSM DSI driver looks for the next bridge during
msm_dsi_modeset_init(). If the bridge is not registered at that point,
this might result in -EPROBE_DEFER, which can be problematic that late
during the device probe process. Move next bridge acquisition to the
dsi_bind state so that probe deferral is returned as early as possible.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/582210/
Link: https://lore.kernel.org/r/20240309-fd-dsi-cleanup-bridges-v1-2-962ebdba82ed@linaro.org
Since the commit 8b03ad30e3 ("drm/msm/dsi: Use one connector for dual
DSI mode"), the second DSI host in the bonded pair will not be
associated with the encoder and will not get the bridges, thus making
condition in msm_dsi_manager_set_split_display() always false.
Technically that change broke bonded DSI support in the MDP5 driver. But
since nobody complained in the last 5.5 years, it seems that nobody
cares enough.
Drop the msm_dsi_manager_set_split_display() completely and stop calling
the set_split_display() KMS callback. Also remove the
msm_dsi::external_bridge field which was only used by the mentioned
function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/561695/
Link: https://lore.kernel.org/r/20231009205727.2781802-4-dmitry.baryshkov@linaro.org
Since the commit 8f59ee9a57 ("drm/msm/dsi: Adjust probe order") the
DSI hosts are not bound through the component framework if the DSI
driver wasn't attached to the DSI device connected to this host.
Afterwards, if there is no bridge (including the panel bridge) created
for the DSI device then devm_drm_of_get_bridge() will return an error,
also making msm_dsi_manager_ext_bridge_init() and thus DSI modesetting
init fail.
This way there can be no 'unconnected' MSM DSI bridges. Remove the
msm_dsi_device_connected() function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/561692/
Link: https://lore.kernel.org/r/20231009205727.2781802-3-dmitry.baryshkov@linaro.org
This helper has been introduced to avoid programmer errors (missing
_put calls leading to dangling refcnt) when using pm_runtime_get, use it.
While at it, start checking the return value.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 5c82902844 ("drm/msm/dsi: Split PHY drivers to separate files")
Patchwork: https://patchwork.freedesktop.org/patch/543350/
Link: https://lore.kernel.org/r/20230620-topic-dsiphy_rpm-v2-1-a11a751f34f0@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes for v6.7-rc3:
- Fix the VREG_CTRL_1 for 4nm CPHY to match downstream
- Remove duplicate call to drm_kms_helper_poll_init() in msm_drm_init()
- Fix the safe_lut_tbl[] for sc8280xp to match downstream
- Don't attach the drm_dp_set_subconnector_property() for eDP
- Fix to attach drm_dp_set_subconnector_property() for DP. Otherwise
there is a bootup crash on multiple targets
- Remove unnecessary NULL check left behind during cleanup
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtkna3P3mvaF53n2ARJACaXQU+OFfShayTrsUVmqCOmNQ@mail.gmail.com
Updates for v6.7
DP:
- use existing helpers for DPCD handling instead of open-coded functions
- set the subconnector type according to the plugged cable / dongle
skip validity check for DP CTS EDID checksum
DPU:
- continued migration of feature flags to use core revision checks
- reworked interrupts code to use '0' as NO_IRQ, removed raw IRQ indices
from log / trace output
gpu:
- a7xx support (a730, a740)
- fixes and additional speedbins for a635, a643
core:
- decouple msm_drv from kms to more cleanly support headless devices (like
imx5+a2xx)
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvzkBL2_OgyOeP_b6rVEjrNdfm8jcKzaB04HqHyT5jYwA@mail.gmail.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmU1ngkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGrsIH/0k/+gdBBYFFdEym
foRhKir9WV3ZX4oIozJjA1f7T+qVYclKs6kaYm3gNepRBb6AoG8pdgv4MMAqhYsf
QMe2XHi0MrO/qKBgfNfivxEa9jq+0QK5uvTbqCRqCAB8LfwVyDqapCmg3EuiZcPW
UbMITmnwLIfXgPxvp9rabmCsTqO6FLbf0GDOVIkNSAIDBXMpcO1iffjrWUbhRa7n
oIoiJmWJLcXLxPWDsRKbpJwzw2cIG08YhfQYAiQnC3YaeRm1FKLDIICRBsmfYzja
rWv9r4dn4TDfV4/AnjggQnsZvz2yPCxNaFSQIT88nIeiLvyuUTJ9j8aidsSfMZQf
xZAbzbA=
=NoQv
-----END PGP SIGNATURE-----
BackMerge tag 'v6.6-rc7' into drm-next
This is needed to add the msm pr which is based on a higher base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the drm/msm init code gets an error during output modeset
initialisation, the kernel will report an error regarding DRM memory
manager not being clean during shutdown. This is because
msm_dsi_modeset_init() allocates a piece of GEM memory for the TX
buffer, but destruction of the buffer happens only at
msm_dsi_host_destroy(), which is called during DSI driver's remove()
time, much later than the DRM MM shutdown.
To solve this issue, move the TX buffer destruction to dsi_unbind(), so
that the buffer is destructed at the correct time. Note, we also have to
store a reference to the address space, because priv->kms->aspace is
cleared before components are unbound.
Reported-by: Bjorn Andersson <andersson@kernel.org>
Fixes: 8f59ee9a57 ("drm/msm/dsi: Adjust probe order")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/562238/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use exiting function to free the allocated GEM object instead of
open-coding it. This has a bonus of internally calling
msm_gem_put_vaddr() to compensate for msm_gem_get_vaddr() in
msm_get_kernel_new().
Fixes: 1e29dff004 ("drm/msm: Add a common function to free kernel buffer objects")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/562239/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Make MSM DSI driver use devm_drm_bridge_add() instead of plain
drm_bridge_add(). As the driver doesn't require any additional cleanup,
stop adding created bridge to the priv->bridges array.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/561636/
Signed-off-by: Rob Clark <robdclark@chromium.org>
drm-misc-next for v6.7-rc1:
UAPI Changes:
- Nouveau changed to not set NO_PREFETCH flag explicitly.
Cross-subsystem Changes:
- Update documentation of dma-buf intro and uapi.
- fbdev/sbus fixes.
- Use initializer macros in a lot of fbdev drivers.
- Add Boris Brezillon as Panfrost driver maintainer.
- Add Jessica Zhang as drm/panel reviewer.
- Make more fbdev drivers use fb_ops helpers for deferred io.
- Small hid trailing whitespace fix.
- Use fb_ops in hid/picolcd
Core Changes:
- Assorted small fixes to ttm tests, drm/mst.
- Documentation updates to bridge.
- Add kunit tests for some drm_fb functions.
- Rework drm_debugfs implementation.
- Update xe documentation to mark todos as completed.
Driver Changes:
- Add support to rockchip for rv1126 mipi-dsi and vop.
- Assorted small fixes to nouveau, bridge/samsung-dsim,
bridge/lvds-codec, loongson, rockchip, panfrost, gma500, repaper,
komeda, virtio, ssd130x.
- Add support for simple panels Mitsubishi AA084XE01,
JDI LPM102A188A,
- Documentation updates to accel/ivpu.
- Some nouveau scheduling/fence fixes.
- Power management related fixes and other fixes to ivpu.
- Assorted bridge/it66121 fixes.
- Make platform drivers return void in remove() callback.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3da6554b-3b47-fe7d-c4ea-21f4f819dbb6@linux.intel.com
Dave Airlie