The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is reloading during recovery flow, it can't get new commands
till command interface is up again. Otherwise we may get to null pointer
trying to access non initialized command structures.
Add cmdif state to avoid processing commands while cmdif is not ready.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After driver creates (via FW command) an EQ for commands, the driver will
be informed on new commands completion by EQE. However, due to a race in
driver's internal command mode metadata update, some new commands will
still be miss-handled by driver as if we are in polling mode. Such commands
can get two non forced completion, leading to already freed command entry
access.
CREATE_EQ command, that maps EQ to the command queue must be posted to the
command queue while it is empty and no other command should be posted.
Add SW mechanism that once the CREATE_EQ command is about to be executed,
all other commands will return error without being sent to the FW. Allow
sending other commands only after successfully changing the driver's
internal command mode metadata.
We can safely return error to all other commands while creating the command
EQ, as all other commands might be sent from the user/application during
driver load. Application can rerun them later after driver's load was
finished.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When FW response to commands is very slow and all command entries in
use are waiting for completion we can have a race where commands can get
timeout before they get out of the queue and handled. Timeout
completion on uninitialized command will cause releasing command's
buffers before accessing it for initialization and then we will get NULL
pointer exception while trying access it. It may also cause releasing
buffers of another command since we may have timeout completion before
even allocating entry index for this command.
Add entry handling completion to avoid this race.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This merge includes updates to bonding driver needed for the rdma stack,
to avoid conflicts with the RDMA branch.
Maor Gottlieb Says:
====================
Bonding: Add support to get xmit slave
The following series adds support to get the LAG master xmit slave by
introducing new .ndo - ndo_get_xmit_slave. Every LAG module can
implement it and it first implemented in the bond driver.
This is follow-up to the RFC discussion [1].
The main motivation for doing this is for drivers that offload part
of the LAG functionality. For example, Mellanox Connect-X hardware
implements RoCE LAG which selects the TX affinity when the resources
are created and port is remapped when it goes down.
The first part of this patchset introduces the new .ndo and add the
support to the bonding module.
The second part adds support to get the RoCE LAG xmit slave by building
skb of the RoCE packet based on the AH attributes and call to the new
.ndo.
The third part change the mlx5 driver driver to set the QP's affinity
port according to the slave which found by the .ndo.
====================
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add function to get the device physical port of the lag slave.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 updates for both net-next and rdma-next:
1) HW bits and definitions for TLS and IPsec offlaods
2) Release all pages capability bits
3) New command interface helpers and some code cleanup as a result
4) Move qp.c out of mlx5 core driver into mlx5_ib rdma driver
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add new TX WQE field for Connect-X6DX trailer insertion support,
when set, the HW adds a trailer to the packet, the WQE trailer
association flags are used to set to HW the header which the
trailer belongs.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a bit in HCA capabilities layout to indicate if release all pages is
supported.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add needed structure layouts and defines for pci sync for fw update
event. The downstream patches will include event handlers for this event
type.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add needed structure layouts and defines for MFRL (Management Firmware
Reset Level) register. This structure will be used for the firmware
upgrade and reset flow in the downstream patches.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The imm_inval_pkey field can hold four different types of data,
depends on the usage, the data could be one of the below:
- Immediate field of the received message
- Invalidate rkey
- Pkey of the packet
- Flow table metadata
Current implementation doesn't reflect the intended usage of the
field at usage time.
Reflect the different types by replace this field with a union,
modify code where this field is used to reflect its intended
usage.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The alignment value is part of the input structure, so use it and spare
extra memory allocation when is not needed.
Now, using the new ability when allocating icm for Direct-Rule
insertion.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add COPY type to modify_header action. IPsec feature is the first
feature that needs COPY steering action.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Do mass update of cq.c to reuse newly introduced
mlx5_cmd_exec_in*() interfaces.
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Currently the FPGA IPsec is the only hw implementation of the IPsec
acceleration api, and so the mlx5_accel_esp_create_hw_context was
wrongly made to suit this HW api, among other in its parameter list
and some of its parameter endianness.
This implementation might not be suitable for different HW.
Refactor by group and pass all function arguments of
mlx5_accel_esp_create_hw_context in common mlx5_accel_esp_xfrm_attrs
struct field of mlx5_accel_esp_xfrm struct and correct the endianness
according to the HW being called.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When this is enabled, UDP source port for RoCEv2 packets are defined
by software instead of firmware.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The mlx5_core doesn't need any functionality coded in qp.c, so move
that file to drivers/infiniband/ be under mlx5_ib responsibility.
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
mlx5 core users are encouraged to use low level API (mlx5_cmd_exec)
without the need of helper functions, do this for q counters, remove
helper functions and call mlx5_cmd_exec directly from users.
This will help reduce the total amount of code and reduction of the
mlx5_core symbol table.
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Many mlx5_cmd_exec() callers are not interested in the output from that
command or have standard in/out structures. Those callers simply allocate
those structure on the stack and use sizeof() to provide in/out arguments.
In this naive approach provide simplified versions of mlx5_cmd_exec().
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The majority of the patches are cleanups, refactorings and clarity
improvements
- Various driver updates for siw, bnxt_re, rxe, efa, mlx5, hfi1
- Lots of cleanup patches for hns
- Convert more places to use refcount
- Aggressively lock the RDMA CM code that syzkaller says isn't working
- Work to clarify ib_cm
- Use the new ib_device lifecycle model in bnxt_re
- Fix mlx5's MR cache which seems to be failing more often with the new
ODP code
- mlx5 'dynamic uar' and 'tx steering' user interfaces
-----BEGIN PGP SIGNATURE-----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=ae+a
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"The majority of the patches are cleanups, refactorings and clarity
improvements.
This cycle saw some more activity from Syzkaller, I think we are now
clean on all but one of those bugs, including the long standing and
obnoxious rdma_cm locking design defect. Continue to see many drivers
getting cleanups, with a few new user visible features.
Summary:
- Various driver updates for siw, bnxt_re, rxe, efa, mlx5, hfi1
- Lots of cleanup patches for hns
- Convert more places to use refcount
- Aggressively lock the RDMA CM code that syzkaller says isn't
working
- Work to clarify ib_cm
- Use the new ib_device lifecycle model in bnxt_re
- Fix mlx5's MR cache which seems to be failing more often with the
new ODP code
- mlx5 'dynamic uar' and 'tx steering' user interfaces"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (144 commits)
RDMA/bnxt_re: make bnxt_re_ib_init static
IB/qib: Delete struct qib_ivdev.qp_rnd
RDMA/hns: Fix uninitialized variable bug
RDMA/hns: Modify the mask of QP number for CQE of hip08
RDMA/hns: Reduce the maximum number of extend SGE per WQE
RDMA/hns: Reduce PFC frames in congestion scenarios
RDMA/mlx5: Add support for RDMA TX flow table
net/mlx5: Add support for RDMA TX steering
IB/hfi1: Call kobject_put() when kobject_init_and_add() fails
IB/hfi1: Fix memory leaks in sysfs registration and unregistration
IB/mlx5: Move to fully dynamic UAR mode once user space supports it
IB/mlx5: Limit the scope of struct mlx5_bfreg_info to mlx5_ib
IB/mlx5: Extend QP creation to get uar page index from user space
IB/mlx5: Extend CQ creation to get uar page index from user space
IB/mlx5: Expose UAR object and its alloc/destroy commands
IB/hfi1: Get rid of a warning
RDMA/hns: Remove redundant judgment of qp_type
RDMA/hns: Remove redundant assignment of wc->smac when polling cq
RDMA/hns: Remove redundant qpc setup operations
RDMA/hns: Remove meaningless prints
...
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
mlx5: Remove uninitialized use of key in mlx5_core_create_mkey
{IB,net}/mlx5: Move asynchronous mkey creation to mlx5_ib
{IB,net}/mlx5: Assign mkey variant in mlx5_ib only
{IB,net}/mlx5: Setup mkey variant before mr create command invocation
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Leon Romanovsky says:
====================
Those two patches from Michael extends mlx5_core and mlx5_ib flow steering
to support RDMA TX in similar way to already supported RDMA RX.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Due to dependencies
* branch 'mlx5_tx_steering':
RDMA/mlx5: Add support for RDMA TX flow table
net/mlx5: Add support for RDMA TX steering
Add new RDMA TX flow steering namespace. Flow steering rules in
this namespace are used to filter transmitted RDMA traffic.
Link: https://lore.kernel.org/r/20200324061425.1570190-2-leon@kernel.org
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
struct mlx5_bfreg_info is used by mlx5_ib only but is exposed to both RDMA
and netdev parts of mlx5 driver. Move that struct to mlx5_ib namespace,
clean vertical space alignment and convert lib_uar_4k from bool to
bitfield.
Link: https://lore.kernel.org/r/20200324060143.1569116-5-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add dependencny on cap termination_table_raw_traffic to allow non
encapsulated packets received from uplink to be forwarded back to the
received uplink port.
Refactor the conditions into a separate function.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Leon Romanovsky says:
====================
This series fixes various corner cases in the mlx5_ib MR cache
implementation, see specific commit messages for more information.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Due to dependencies
* branch 'mlx5_mr-cache':
RDMA/mlx5: Allow MRs to be created in the cache synchronously
RDMA/mlx5: Revise how the hysteresis scheme works for cache filling
RDMA/mlx5: Fix locking in MR cache work queue
RDMA/mlx5: Lock access to ent->available_mrs/limit when doing queue_work
RDMA/mlx5: Fix MR cache size and limit debugfs
RDMA/mlx5: Always remove MRs from the cache before destroying them
RDMA/mlx5: Simplify how the MR cache bucket is located
RDMA/mlx5: Rename the tracking variables for the MR cache
RDMA/mlx5: Replace spinlock protected write with atomic var
{IB,net}/mlx5: Move asynchronous mkey creation to mlx5_ib
{IB,net}/mlx5: Assign mkey variant in mlx5_ib only
{IB,net}/mlx5: Setup mkey variant before mr create command invocation
As mlx5_ib is the only user of the mlx5_core_create_mkey_cb, move the
logic inside mlx5_ib and cleanup the code in mlx5_core.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
mkey variant is not required for mlx5_core use, move the mkey variant
counter to mlx5_ib.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Enable reg c1 loopback if firmware reports it's supported,
as this is needed for restoring packet metadata (e.g chain).
Also define helper to query if it is enabled.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now the flex parser capability was used in ib_query_device() to
indicate tunnel_offloads_caps support for mpls_over_gre/mpls_over_udp.
Newer devices and firmware will have configurations with the flexparser
but without mpls support.
Testing for the flex parser capability was a mistake, the tunnel_stateless
capability was intended for detecting mpls and was introduced at the same
time as the flex parser capability.
Otherwise userspace will be incorrectly informed that a future device
supports MPLS when it does not.
Link: https://lore.kernel.org/r/20200305123841.196086-1-leon@kernel.org
Cc: <stable@vger.kernel.org> # 4.17
Fixes: e818e255a5 ("IB/mlx5: Expose MPLS related tunneling offloads")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Yishai Hadas Says:
====================
Expose raw packet pacing APIs to be used by DEVX based applications. The
existing code was refactored to have a single flow with the new raw APIs.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Due to dependencies
* branch 'mlx5_packet_pacing':
IB/mlx5: Introduce UAPIs to manage packet pacing
net/mlx5: Expose raw packet pacing APIs
This series adds some HW bits and definitions for mlx5 driver, to be
used by downstream features in both rdma and netdev branches.
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: HW bit for goto chain offload support
net/mlx5: Expose link speed directly
net/mlx5: Introduce TLS and IPSec objects enums
net/mlx5: Introduce egress acl forward-to-vport capability
net/mlx5: Expose raw packet pacing APIs
net/mlx5e: Replace zero-length array with flexible-array member
net/mlx5: fix spelling mistake "reserverd" -> "reserved"
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Expose port rate as part of the port speed register fields.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Expose the TLS encryption key general object type enum correctly,
and add the IPSec encryption key general object type enum.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add HCA_CAP.egress_acl_forward_to_vport field to check whether HW
supports e-switch vport's egress acl to forward packets to other
e-switch vport or not.
By default E-Switch egress ACL forwards eswitch vports egress packets
to their corresponding NIC/VF vports.
With this cap enabled, the driver is allowed to alter this behavior
and forward packets to arbitrary NIC/VF vports with the following
limitations:
a. Multiple processing paths are supported if all of the following
conditions are met:
- HCA_CAP.egress_acl_forward_to_vport is set ==1.
- A destination of type Flow Table only appears once, as the
last destination in the list.
- Vport destination is supported if
HCA_CAP.egress_acl_forward_to_vport==1. Vport must not be
the Uplink.
b. Flow_tag not supported.
c. This table is only applicable after an FDB table is created.
d. Push VLAN action is not supported.
e. Pop VLAN action cannot be added concurrently to this table and
FDB table.
This feature will be used during port failover in bonding scenario
where two VFs representors are bonded to handle failover egress traffic
(VM's ingress/receive traffic).
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Expose raw packet pacing APIs to be used by DEVX based applications.
The existing code was refactored to have a single flow with the new raw
APIs.
The new raw APIs considered the input of 'pp_rate_limit_context', uid,
'dedicated', upon looking for an existing entry.
This raw mode enables future device specification data in the raw
context without changing the existing logic and code.
The ability to ask for a dedicated entry gives control for application
to allocate entries according to its needs.
A dedicated entry may not be used by some other process and it also
enables the process spreading its resources to some different entries
for use different hardware resources as part of enforcing the rate.
The counter per entry was changed to be u64 to prevent any option to
overflow.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
When using port mirroring, we forward the traffic to another table and
use that table to forward to the mirrored vport. Since the hardware
loses the values of reg c, and in particular reg c0, we fail the match
on the input vport which previously existed in reg c0. To overcome this
situation, we use a set of per vport tables, positioned at the lowest
priority, and forward traffic to those tables. Since these tables are
per vport, we can avoid matching on reg c0.
Fixes: c01cfd0f11 ("net/mlx5: E-Switch, Add match on vport metadata for rule in fast path")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On RX side create a restore table in OFFLOADS namespace.
This table will match on all values for reg_c0 we will use,
and set it to the flow_tag. This flow tag can then be read on the CQE.
As there is no copy action from reg c0 to flow tag, instead we have to
set the flow tag explictily. We add an API so callers can add all the used
reg_c0 values (tags) and for each of those we add a restore rule.
This will be used in a following patch to save the miss chain mapping
tag on reg_c0 and from it restore the tc chain on the skb.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Multi chain support requires the miss path to continue the processing
from the last chain id, and for that we need to save the chain
miss tag (a mapping for 32bit chain id) on reg_c0 which will
come in a next patch.
Currently reg_c0 is exclusively used to store the source port
metadata, giving it 32bit, it is created from 16bits of vcha_id,
and 16bits of vport number.
We will move this source port metadata to upper 16bits, and leave the
lower bits for the chain miss tag. We compress the reg_c0 source port
metadata to 16bits by taking 8 bits from vhca_id, and 8bits from
the vport number.
Since we compress the vport number to 8bits statically, and leave two
top ids for special PF/ECPF numbers, we will only support a max of 254
vports with this strategy.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On driver load:
- Initialize resource dump data structure and memory access tools (mkey
& pd).
- Read the resource dump's menu which contains the FW segment
identifier. Each record is identified by the segment name (ASCII).
During the driver's course of life, users (like reporters) may request
dumps per segment. The user should create a command providing the
segment identifier (SW enumeration) and command keys. In return, the
user receives a command context. In order to receive the dump, the user
should supply the command context and a memory (aligned to a PAGE) on
which the dump content will be written. Since the dump may be larger
than the given memory, the user may resubmit the command until received
an indication of end-of-dump. It is the user's responsibility to destroy
the command.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On flow table creation, send the relevant flags according to what the FW
currently supports.
When FW doesn't support reformat option over SW-steering managed table,
the driver shouldn't pass this.
Fixes: 988fd6b32d ("net/mlx5: DR, Pass table flags at creation to lower layer")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The reserved member should be named reserved.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
David S. Miller