Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Fixes: 7687a5b0ee ("gpio: modepin: Add driver support for modepin GPIO controller")
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240902115848.904227-1-liaochen4@huawei.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
During Linux graceful reboot, the GPIO interrupts are not disabled.
Since the drivers are not removed during graceful reboot,
the logic to call mlxbf3_gpio_irq_disable() is not triggered.
Interrupts that remain enabled can cause issues on subsequent boots.
For example, the mlxbf-gige driver contains PHY logic to bring up the link.
If the gpio-mlxbf3 driver loads first, the mlxbf-gige driver
will use a GPIO interrupt to bring up the link.
Otherwise, it will use polling.
The next time Linux boots and loads the drivers in this order, we encounter the issue:
- mlxbf-gige loads first and uses polling while the GPIO10
interrupt is still enabled from the previous boot. So if
the interrupt triggers, there is nothing to clear it.
- gpio-mlxbf3 loads.
- i2c-mlxbf loads. The interrupt doesn't trigger for I2C
because it is shared with the GPIO interrupt line which
was not cleared.
The solution is to add a shutdown function to the GPIO driver to clear and disable
all interrupts. Also clear the interrupt after disabling it in mlxbf3_gpio_irq_disable().
Fixes: 38a700efc5 ("gpio: mlxbf3: Add gpio driver support")
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240611171509.22151-1-asmaa@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
- don't use sprintf() with non-constant format string
-----BEGIN PGP SIGNATURE-----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=H8F0
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
- don't use sprintf() with non-constant format string
* tag 'gpio-fixes-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: virtuser: avoid non-constant format string
- Treewide conversion of of_property_for_each_u32() to drop internal
arguments making struct property opaque
- Add binding for Amlogic A4 SoC watchdog
- Fix constraints for AD7192 'single-channel' property
-----BEGIN PGP SIGNATURE-----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=Nn/d
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull more devicetree updates from Rob Herring:
"Most of this is a treewide change to of_property_for_each_u32() which
was small enough to do in one go before rc1 and avoids the need to
create of_property_for_each_u32_some_new_name().
- Treewide conversion of of_property_for_each_u32() to drop internal
arguments making struct property opaque
- Add binding for Amlogic A4 SoC watchdog
- Fix constraints for AD7192 'single-channel' property"
* tag 'devicetree-fixes-for-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: iio: adc: ad7192: Fix 'single-channel' constraints
of: remove internal arguments from of_property_for_each_u32()
dt-bindings: watchdog: add support for Amlogic A4 SoCs
Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases to
get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions. It's not all that useful for a "write a whole driver
in rust" type of thing, but the firmware bindings do help out the
phy rust drivers, and the driver core bindings give a solid base on
which others can start their work. There is still a long way to go
here before we have a multitude of rust drivers being added, but
it's a great first step.
- driver core const api changes. This reached across all bus types,
and there are some fix-ups for some not-common bus types that
linux-next and 0-day testing shook out. This work is being done to
help make the rust bindings more safe, as well as the C code, moving
toward the end-goal of allowing us to put driver structures into
read-only memory. We aren't there yet, but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZqH+aQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoOQCfVBdLcBjEDAGh3L8qHRGMPy4rV2EAoL/r+zKm
cJEYtJpGtWX6aAtugm9E
=ZyJV
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases
to get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions.
It's not all that useful for a "write a whole driver in rust" type
of thing, but the firmware bindings do help out the phy rust
drivers, and the driver core bindings give a solid base on which
others can start their work.
There is still a long way to go here before we have a multitude of
rust drivers being added, but it's a great first step.
- driver core const api changes.
This reached across all bus types, and there are some fix-ups for
some not-common bus types that linux-next and 0-day testing shook
out.
This work is being done to help make the rust bindings more safe,
as well as the C code, moving toward the end-goal of allowing us to
put driver structures into read-only memory. We aren't there yet,
but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
ARM: sa1100: make match function take a const pointer
sysfs/cpu: Make crash_hotplug attribute world-readable
dio: Have dio_bus_match() callback take a const *
zorro: make match function take a const pointer
driver core: module: make module_[add|remove]_driver take a const *
driver core: make driver_find_device() take a const *
driver core: make driver_[create|remove]_file take a const *
firmware_loader: fix soundness issue in `request_internal`
firmware_loader: annotate doctests as `no_run`
devres: Correct code style for functions that return a pointer type
devres: Initialize an uninitialized struct member
devres: Fix memory leakage caused by driver API devm_free_percpu()
devres: Fix devm_krealloc() wasting memory
driver core: platform: Switch to use kmemdup_array()
driver core: have match() callback in struct bus_type take a const *
MAINTAINERS: add Rust device abstractions to DRIVER CORE
device: rust: improve safety comments
MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer
MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER
firmware: rust: improve safety comments
...
The of_property_for_each_u32() macro needs five parameters, two of which
are primarily meant as internal variables for the macro itself (in the
for() clause). Yet these two parameters are used by a few drivers, and this
can be considered misuse or at least bad practice.
Now that the kernel uses C11 to build, these two parameters can be avoided
by declaring them internally, thus changing this pattern:
struct property *prop;
const __be32 *p;
u32 val;
of_property_for_each_u32(np, "xyz", prop, p, val) { ... }
to this:
u32 val;
of_property_for_each_u32(np, "xyz", val) { ... }
However two variables cannot be declared in the for clause even with C11,
so declare one struct that contain the two variables we actually need. As
the variables inside this struct are not meant to be used by users of this
macro, give the struct instance the noticeable name "_it" so it is visible
during code reviews, helping to avoid new code to use it directly.
Most usages are trivially converted as they do not use those two
parameters, as expected. The non-trivial cases are:
- drivers/clk/clk.c, of_clk_get_parent_name(): easily doable anyway
- drivers/clk/clk-si5351.c, si5351_dt_parse(): this is more complex as the
checks had to be replicated in a different way, making code more verbose
and somewhat uglier, but I refrained from a full rework to keep as much
of the original code untouched having no hardware to test my changes
All the changes have been build tested. The few for which I have the
hardware have been runtime-tested too.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> # drivers/clk/sunxi/clk-simple-gates.c, drivers/clk/sunxi/clk-sun8i-bus-gates.c
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # drivers/gpio/gpio-brcmstb.c
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # drivers/irqchip/irq-atmel-aic-common.c
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # drivers/iio/adc/ti_am335x_adc.c
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> # drivers/pwm/pwm-samsung.c
Acked-by: Richard Leitner <richard.leitner@linux.dev> # drivers/usb/misc/usb251xb.c
Acked-by: Mark Brown <broonie@kernel.org> # sound/soc/codecs/arizona.c
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> # sound/soc/codecs/arizona.c
Acked-by: Michael Ellerman <mpe@ellerman.id.au> # arch/powerpc/sysdev/xive/spapr.c
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20240724-of_property_for_each_u32-v3-1-bea82ce429e2@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Several new features here:
- Virtio find vqs API has been reworked
(required to fix the scalability issue we have with
adminq, which I hope to merge later in the cycle)
- vDPA driver for Marvell OCTEON
- virtio fs performance improvement
- mlx5 migration speedups
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmaXjQQPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpnIsH/jVNqAQbe/vaBQdNMdnsA+P9A9unLbYRxYCQ
tN73mQRIXKtnZHBRAEbMGq52HPYg8HlN2HJSgyNo6I6t8VD+PiOco7m+3GpmqEcW
aXPOPl0BAbVoDgyutxRuuodP8Z61lBx0mG6iOxpzTXOPGlpQqtPCFHO8YnodqnPf
tMix/5uAqgZKV2siCbw5DtzwEc0gDHU8qsD0/nyoS5nBDF9yh/ardr5P/qiyFDQH
atCNYTOhIFU83pLAaw0fpCGbkt7gxf+5RpWVx3wkYww+/MwvYhsveRvQyaGbBz3n
WDtET3SOtVTta98OAGIKCq/2z8f6mYXBP7vXapBgnJG3vwS/poQ=
=LYua
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- Virtio find vqs API has been reworked (required to fix the
scalability issue we have with adminq, which I hope to merge later
in the cycle)
- vDPA driver for Marvell OCTEON
- virtio fs performance improvement
- mlx5 migration speedups
Fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (56 commits)
virtio: rename virtio_find_vqs_info() to virtio_find_vqs()
virtio: remove unused virtio_find_vqs() and virtio_find_vqs_ctx() helpers
virtio: convert the rest virtio_find_vqs() users to virtio_find_vqs_info()
virtio_balloon: convert to use virtio_find_vqs_info()
virtiofs: convert to use virtio_find_vqs_info()
scsi: virtio_scsi: convert to use virtio_find_vqs_info()
virtio_net: convert to use virtio_find_vqs_info()
virtio_crypto: convert to use virtio_find_vqs_info()
virtio_console: convert to use virtio_find_vqs_info()
virtio_blk: convert to use virtio_find_vqs_info()
virtio: rename find_vqs_info() op to find_vqs()
virtio: remove the original find_vqs() op
virtio: call virtio_find_vqs_info() from virtio_find_single_vq() directly
virtio: convert find_vqs() op implementations to find_vqs_info()
virtio_pci: convert vp_*find_vqs() ops to find_vqs_info()
virtio: introduce virtio_queue_info struct and find_vqs_info() config op
virtio: make virtio_find_single_vq() call virtio_find_vqs()
virtio: make virtio_find_vqs() call virtio_find_vqs_ctx()
caif_virtio: use virtio_find_single_vq() for single virtqueue finding
vdpa/mlx5: Don't enable non-active VQs in .set_vq_ready()
...
Using a string variable as an sprintf format is potentially
dangerous, and gcc can warn about this:
drivers/gpio/gpio-virtuser.c: In function 'gpio_virtuser_dbgfs_init_line_attrs':
drivers/gpio/gpio-virtuser.c:808:9: error: format not a string literal and no format arguments [-Werror=format-security]
808 | sprintf(data->consumer, id);
| ^~~~~~~
Change it to a simpler strscpy() instead to just copy it and check
the destination buffer size.
Fixes: 91581c4b3f ("gpio: virtuser: new virtual testing driver for the GPIO API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240719144422.2082394-1-arnd@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Since the original virtio_find_vqs() is no longer present, rename
virtio_find_vqs_info() back to virtio_find_vqs().
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Message-Id: <20240708074814.1739223-20-jiri@resnulli.us>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of passing separate names and callbacks arrays
to virtio_find_vqs(), have one of virtual_queue_info structs and
pass it to virtio_find_vqs_info().
Suggested-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Message-Id: <20240708074814.1739223-18-jiri@resnulli.us>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
GPIOLIB core:
- rework kfifo handling rework in the character device code
- improve the labeling of GPIOs requested as interrupts and show more info
on interrupt-only GPIOs in debugfs
- remove unused APIs
- unexport interfaces that are only used from the core GPIO code
- drop the return value from gpiochip_set_desc_names() as it cannot fail
- move a string array definition out of a header and into a specific
compilation unit
- convert the last user of gpiochip_get_desc() other than GPIO core to using
a safer alternative
- use array_index_nospec() where applicable
New drivers:
- add a "virtual GPIO consumer" module that allows requesting GPIOs from actual
hardware and driving tests of the in-kernel GPIO API from user-space over
debugfs
- add a GPIO-based "sloppy" logic analyzer module useful for "first glance"
debugging on remote boards
Driver improvements:
- add support for a new model to gpio-pca953x
- lock GPIOs as interrupts in gpio-sim when the lines are requested as irqs
via the simulator domain + some other minor improvements
- improve error reporting in gpio-syscon
- convert gpio-ath79 to using dynamic GPIO base and range
- use pcibios_err_to_errno() for converting PCIBIOS error codes to errno
vaues in gpio-amd8111 and gpio-rdc321x
- allow building gpio-brcmstb for the BCM2835 architecture
DT bindings:
- convert DT bindings for lsi,zevio, mpc8xxx, and atmel to DT schema
- document new properties for aspeed,gpio, fsl,qoriq-gpio and gpio-vf610
- document new compatibles for pca953x and fsl,qoriq-gpio
Documentation:
- document stricter behavior of the GPIO character device uAPI with regards to
reconfiguring requested line without direction set
- clarify the effect of the active-low flag on line values and edges
- remove documentation for the legacy GPIO API in order to stop tempting
people to use it
- document the preference for using pread() for reading edge events in the
sysfs API
Other:
- add an extended initializer to the interrupt simulator allowing to specify
a number of callbacks callers can use to be notified about irqs being
requested and released
-----BEGIN PGP SIGNATURE-----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=kK88
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"The majority of added lines are two new modules: the GPIO virtual
consumer module that improves our ability to add automated tests for
the kernel API and the "sloppy" logic analyzer module that uses the
GPIO API to implement a coarse-grained debugging tool for useful for
remote development.
Other than that we have the usual assortment of various driver
extensions, improvements to the core GPIO code, DT-bindings and other
documentation updates as well as an extension to the interrupt
simulator:
GPIOLIB core:
- rework kfifo handling rework in the character device code
- improve the labeling of GPIOs requested as interrupts and show more
info on interrupt-only GPIOs in debugfs
- remove unused APIs
- unexport interfaces that are only used from the core GPIO code
- drop the return value from gpiochip_set_desc_names() as it cannot
fail
- move a string array definition out of a header and into a specific
compilation unit
- convert the last user of gpiochip_get_desc() other than GPIO core
to using a safer alternative
- use array_index_nospec() where applicable
New drivers:
- add a "virtual GPIO consumer" module that allows requesting GPIOs
from actual hardware and driving tests of the in-kernel GPIO API
from user-space over debugfs
- add a GPIO-based "sloppy" logic analyzer module useful for "first
glance" debugging on remote boards
Driver improvements:
- add support for a new model to gpio-pca953x
- lock GPIOs as interrupts in gpio-sim when the lines are requested
as irqs via the simulator domain + some other minor improvements
- improve error reporting in gpio-syscon
- convert gpio-ath79 to using dynamic GPIO base and range
- use pcibios_err_to_errno() for converting PCIBIOS error codes to
errno vaues in gpio-amd8111 and gpio-rdc321x
- allow building gpio-brcmstb for the BCM2835 architecture
DT bindings:
- convert DT bindings for lsi,zevio, mpc8xxx, and atmel to DT schema
- document new properties for aspeed,gpio, fsl,qoriq-gpio and
gpio-vf610
- document new compatibles for pca953x and fsl,qoriq-gpio
Documentation:
- document stricter behavior of the GPIO character device uAPI with
regards to reconfiguring requested line without direction set
- clarify the effect of the active-low flag on line values and edges
- remove documentation for the legacy GPIO API in order to stop
tempting people to use it
- document the preference for using pread() for reading edge events
in the sysfs API
Other:
- add an extended initializer to the interrupt simulator allowing to
specify a number of callbacks callers can use to be notified about
irqs being requested and released"
* tag 'gpio-updates-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (41 commits)
gpio: mc33880: Convert comma to semicolon
gpio: virtuser: actually use the "trimmed" local variable
dt-bindings: gpio: convert Atmel GPIO to json-schema
gpio: virtuser: new virtual testing driver for the GPIO API
dt-bindings: gpio: vf610: Allow gpio-line-names to be set
gpio: sim: lock GPIOs as interrupts when they are requested
genirq/irq_sim: add an extended irq_sim initializer
dt-bindings: gpio: fsl,qoriq-gpio: Add compatible string fsl,ls1046a-gpio
gpiolib: unexport gpiochip_get_desc()
gpio: add sloppy logic analyzer using polling
Documentation: gpio: Reconfiguration with unset direction (uAPI v2)
Documentation: gpio: Reconfiguration with unset direction (uAPI v1)
dt-bindings: gpio: fsl,qoriq-gpio: add common property gpio-line-names
gpio: ath79: convert to dynamic GPIO base allocation
pinctrl: da9062: replace gpiochip_get_desc() with gpio_device_get_desc()
gpiolib: put gpio_suffixes in a single compilation unit
Documentation: gpio: Clarify effect of active low flag on line edges
Documentation: gpio: Clarify effect of active low flag on line values
gpiolib: Remove data-less gpiochip_add() function
gpio: sim: use devm_mutex_init()
...
The GPIO subsystem used to have a serious problem with undefined behavior
and use-after-free bugs on hot-unplug of GPIO chips. This can be
considered a corner-case by some as most GPIO controllers are enabled
early in the boot process and live until the system goes down but most
GPIO drivers do allow unbind over sysfs, many are loadable modules that
can be (force) unloaded and there are also GPIO devices that can be
dynamically detached, for instance CP2112 which is a USB GPIO expender.
Bugs can be triggered both from user-space as well as by in-kernel users.
We have the means of testing it from user-space via the character device
but the issues manifest themselves differently in the kernel.
This is a proposition of adding a new virtual driver - a configurable
GPIO consumer that can be configured over configfs (similarly to
gpio-sim) or described on the device-tree.
This driver is aimed as a helper in spotting any regressions in
hot-unplug handling in GPIOLIB.
Link: https://lore.kernel.org/r/20240708142912.120570-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
DTS for Nokia N900 incorrectly specifies "active high" polarity for
the reset line, while the chip documentation actually specifies it as
"active low". In the past the driver fudged gpiod API and inverted
the logic internally, but it was changed in d0d89493bf.
Fixes: d0d89493bf ("Input: tsc2004/5 - switch to using generic device properties")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/ZoWXwYtwgJIxi-hD@google.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use the extended irq_sim interface to supply the simulated interrupt
domain with callbacks allowing the GPIO sim to lock/unlock GPIOs
requested as interrupts.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240624093934.17089-3-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
bgpio_bits must be aligned with the data bus width. For example, on a
32 bit big endian system and we only have 16 GPIOs. If we only assume
bgpio_bits=16 we can never control the GPIO because the base address
is the lowest address.
low address high address
-------------------------------------------------
| byte3 | byte2 | byte1 | byte0 |
-------------------------------------------------
| NaN | NaN | gpio8-15 | gpio0-7 |
-------------------------------------------------
Fixes: 55b2395e4e ("gpio: mmio: handle "ngpios" properly in bgpio_init()")
Fixes: https://github.com/openwrt/openwrt/issues/15739
Reported-by: Mark Mentovai <mark@mentovai.com>
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Suggested-By: Mark Mentovai <mark@mentovai.com>
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Lóránd Horváth <lorand.horvath82@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/TYCP286MB089577B47D70F0AB25ABA6F5BCD52@TYCP286MB0895.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
In the match() callback, the struct device_driver * should not be
changed, so change the function callback to be a const *. This is one
step of many towards making the driver core safe to have struct
device_driver in read-only memory.
Because the match() callback is in all busses, all busses are modified
to handle this properly. This does entail switching some container_of()
calls to container_of_const() to properly handle the constant *.
For some busses, like PCI and USB and HV, the const * is cast away in
the match callback as those busses do want to modify those structures at
this point in time (they have a local lock in the driver structure.)
That will have to be changed in the future if they wish to have their
struct device * in read-only-memory.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Alex Elder <elder@kernel.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/2024070136-wrongdoer-busily-01e8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function has been deprecated for some time and is now only used
within the GPIOLIB core. Remove it from the public header and unexport
it as all current users are linked against the compilation unit where
it is defined.
Link: https://lore.kernel.org/r/20240625073815.12376-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
As it turns out, there is a large number of out-of-tree DTSes (in
OpenWrt project) that used to specify incorrect (active high) polarity
for the Lantiq reset GPIO, so to keep compatibility while they are
being updated a quirk for force the polarity low is needed. Luckily
these old DTSes used nonstandard name for the property ("gpio-reset" vs
"reset-gpios") so the quirk will not hurt if there are any new devices
that need inverted polarity as they can specify the right polarity in
their DTS when using the standard "reset-gpios" property.
Additionally the condition to enable the transition from standard to
non-standard reset GPIO property name was inverted and the replacement
name for the property was not correct. Fix this as well.
Fixes: fbbbcd177a ("gpiolib: of: add quirk for locating reset lines with legacy bindings")
Fixes: 90c2d2eb7a ("MIPS: pci: lantiq: switch to using gpiod API")
Reported-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/ZoLpqv1PN08xHioh@google.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This is a sloppy logic analyzer using GPIOs. It comes with a script to
isolate a CPU for polling. While this is definitely not a production
level analyzer, it can be a helpful first view when remote debugging.
Read the documentation for details.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240620094159.6785-2-wsa+renesas@sang-engineering.com
[Bartosz: moved the Kconfig entry into a different category]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
linereq_set_config() behaves badly when direction is not set.
The configuration validation is borrowed from linereq_create(), where,
to verify the intent of the user, the direction must be set to in order to
effect a change to the electrical configuration of a line. But, when
applied to reconfiguration, that validation does not allow for the unset
direction case, making it possible to clear flags set previously without
specifying the line direction.
Adding to the inconsistency, those changes are not immediately applied by
linereq_set_config(), but will take effect when the line value is next get
or set.
For example, by requesting a configuration with no flags set, an output
line with GPIO_V2_LINE_FLAG_ACTIVE_LOW and GPIO_V2_LINE_FLAG_OPEN_DRAIN
set could have those flags cleared, inverting the sense of the line and
changing the line drive to push-pull on the next line value set.
Skip the reconfiguration of lines for which the direction is not set, and
only reconfigure the lines for which direction is set.
Fixes: a54756cb24 ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240626052925.174272-3-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
linehandle_set_config() behaves badly when direction is not set.
The configuration validation is borrowed from linehandle_create(), where,
to verify the intent of the user, the direction must be set to in order
to effect a change to the electrical configuration of a line. But, when
applied to reconfiguration, that validation does not allow for the unset
direction case, making it possible to clear flags set previously without
specifying the line direction.
Adding to the inconsistency, those changes are not immediately applied by
linehandle_set_config(), but will take effect when the line value is next
get or set.
For example, by requesting a configuration with no flags set, an output
line with GPIOHANDLE_REQUEST_ACTIVE_LOW and GPIOHANDLE_REQUEST_OPEN_DRAIN
requested could have those flags cleared, inverting the sense of the line
and changing the line drive to push-pull on the next line value set.
Ensure the intent of the user by disallowing configurations which do not
have direction set, returning an error to userspace to indicate that the
configuration is invalid.
And, for clarity, use lflags, a local copy of gcnf.flags, throughout when
dealing with the requested flags, rather than a mixture of both.
Fixes: e588bb1eae ("gpio: add new SET_CONFIG ioctl() to gpio chardev")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240626052925.174272-2-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
ath79 target has already been converted to device tree based platform.
Use dynamic GPIO numberspace base to suppress the warning:
gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
Tested on Atheros AR7241 and AR9344.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/TYCP286MB089598EA71E964BD8AB9EFD3BCD62@TYCP286MB0895.JPNP286.PROD.OUTLOOK.COM
[Bartosz: tweaked the commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Value of pdata->gpio_unbanked is taken from Device Tree. In case of broken
DT due to any error this value can be any. Without this value validation
there can be out of chips->irqs array boundaries access in
davinci_gpio_probe().
Validate the obtained nirq value so that it won't exceed the maximum
number of IRQs per bank.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: eb3744a2dd ("gpio: davinci: Do not assume continuous IRQ numbering")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Link: https://lore.kernel.org/r/20240618144344.16943-1-amishin@t-argos.ru
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Ensure that `i2c_lock' is held when setting interrupt latch and mask in
pca953x_irq_bus_sync_unlock() in order to avoid races.
The other (non-probe) call site pca953x_gpio_set_multiple() ensures the
lock is held before calling pca953x_write_regs().
The problem occurred when a request raced against irq_bus_sync_unlock()
approximately once per thousand reboots on an i.MX8MP based system.
* Normal case
0-0022: write register AI|3a {03,02,00,00,01} Input latch P0
0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0
0-0022: write register AI|08 {ff,00,00,00,00} Output P3
0-0022: write register AI|12 {fc,00,00,00,00} Config P3
* Race case
0-0022: write register AI|08 {ff,00,00,00,00} Output P3
0-0022: write register AI|08 {03,02,00,00,01} *** Wrong register ***
0-0022: write register AI|12 {fc,00,00,00,00} Config P3
0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Link: https://lore.kernel.org/r/20240620042915.2173-1-ian.ray@gehealthcare.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The gpio_suffixes array is defined in the gpiolib.h header. This means
the array is stored in .rodata of every compilation unit that includes
it. Put the definition for the array in gpiolib.c and export just the
symbol in the header. We need the size of the array so expose it too.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20240612184821.58053-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Drop the hand-coded devres action callback for destroying the mutex in
favor of devm_mutex_init().
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240610140548.35358-4-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We included kernel.h for ARRAY_SIZE() which has since been moved into
its own header. Use it instead.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240610140548.35358-3-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use the dedicated helper for comparing device names against strings.
While at it: reshuffle the code a bit for less indentation.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240610140548.35358-2-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
On x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpio/gpio-gw-pld.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpio/gpio-mc33880.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/gpio/gpio-pcf857x.o
Add the missing invocations of the MODULE_DESCRIPTION() macro,
including the one missing in gpio-pl061.c, which is not built for x86.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240606-md-drivers-gpio-v1-1-cb42d240ca5c@quicinc.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Show more info for interrupt only lines in debugfs. It's useful
to monitor the lines that have been never requested as GPIOs,
but IRQs.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240530191418.1138003-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The TQMx86 GPIO controller only supports falling and rising edge
triggers, but not both. Fix this by implementing a software both-edge
mode that toggles the edge type after every interrupt.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Co-developed-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/515324f0491c4d44f4ef49f170354aca002d81ef.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
irq_set_type() should not implicitly unmask the IRQ.
All accesses to the interrupt configuration register are moved to a new
helper tqmx86_gpio_irq_config(). We also introduce the new rule that
accessing irq_type must happen while locked, which will become
significant for fixing EDGE_BOTH handling.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/6aa4f207f77cb58ef64ffb947e91949b0f753ccd.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The TQMx86 GPIO controller uses the same register address for input and
output data. Reading the register will always return current inputs
rather than the previously set outputs (regardless of the current
direction setting). Therefore, using a RMW pattern does not make sense
when setting output values. Instead, the previously set output register
value needs to be stored as a shadow register.
As there is no reliable way to get the current output values from the
hardware, also initialize all channels to 0, to ensure that stored and
actual output values match. This should usually not have any effect in
practise, as the TQMx86 UEFI sets all outputs to 0 during boot.
Also prepare for extension of the driver to more than 8 GPIOs by using
DECLARE_BITMAP.
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/d0555933becd45fa92a85675d26e4d59343ddc01.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for the TI TCA9535 variant.
The NXP PCA9535 is already supported by the driver.
TCA9535 supports lower voltage operation (down to 1.65V VCC)
compared to PCA (down to 2.3V VCC).
>From a software perspective, these models are equivalent as they
have the same register map.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240531121801.2161154-1-festevam@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The GPIO_BRCMSTB hardware IP is also included in the bcm2712
SoC so enable the driver to also be built for ARCH_BCM2835.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240530181737.1261450-1-pbrobinson@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The handling of kfifo_out() errors in read functions obscures any error.
The error condition should never occur but, while a ret is set to -EIO, it
is subsequently ignored and the read functions instead return the number
of bytes copied to that point, potentially masking the fact that any error
occurred.
Log a warning and return -EIO in the case of a kfifo_out() error to make
it clear something very odd is going on here.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240529131953.195777-4-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The allocation of the linereq events kfifo is performed in two separate
places. Add a helper function to remove the duplication.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240529131953.195777-3-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The initialisation of the linereq events kfifo relies on the struct being
zeroed and a subsequent call to kfifo_alloc(). The call to kfifo_alloc()
is deferred until edge detection is first enabled for the linereq. If the
kfifo is inadvertently accessed before the call to kfifo_alloc(), as was
the case in a recently discovered bug, it behaves as a FIFO of size 1 with
an element size of 0, so writes and reads to the kfifo appear successful
but copy no actual data.
As a defensive measure, initialise the kfifo with INIT_KFIFO() when the
events kfifo is constructed. This initialises the kfifo element size
and zeroes its data pointer, so any inadvertant access prior to the
kfifo_alloc() call will trigger an oops.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240529131953.195777-2-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
rdc_gpio_config() uses pci_{read,write}_config_dword() that return
PCIBIOS_* codes. rdc_gpio_config() is used for
direction_{input,output}() in the struct gpio_chip which both require
normal errnos to be returned.
Similarly, rdc321x_gpio_probe() that is probe function returns
PCIBIOS_* codes without converting them first into normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning them to fix both issues.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240527132345.13956-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
amd_gpio_init() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The return code is then returned as is but amd_gpio_init() is
a module init function that should return normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning it from amd_gpio_init().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240527132345.13956-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Do not issue "can't read the data register offset!" when gpio,syscon-dev
is not set albeit unneeded. gpio-syscon is used with rk3328 chip, but
this iomem region is documented in
Documentation/devicetree/bindings/gpio/rockchip,rk3328-grf-gpio.yaml and
does not require gpio,syscon-dev setting.
Signed-off-by: Etienne Buira <etienne.buira@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/Zktwd4Y8zu6XSGaE@Z926fQmE5jqhFMgp6
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Userspace may trigger a speculative read of an address outside the gpio
descriptor array.
Users can do that by calling gpio_ioctl() with an offset out of range.
Offset is copied from user and then used as an array index to get
the gpio descriptor without sanitization in gpio_device_get_desc().
This change ensures that the offset is sanitized by using
array_index_nospec() to mitigate any possibility of speculative
information leaks.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Signed-off-by: Hagar Hemdan <hagarhem@amazon.com>
Link: https://lore.kernel.org/r/20240523085332.1801-1-hagarhem@amazon.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Several new features here:
- virtio-net is finally supported in vduse.
- Virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmZN570PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp2JUH/1K3fZOHymop6Y5Z3USFS7YdlF+dniedY/vg
TKyWERkXOlxq1d9DVxC0mN7tk72DweuWI0YJjLXofrEW1VuW29ecSbyFXxpeWJls
b7ErffxDAFRas5jkMCngD8TuFnbEegU0mGP5kbiHpEndBydQ2hH99Gg0x7swW+cE
xsvU5zonCCLwLGIP2DrVrn9qGOHtV6o8eZfVKDVXfvicn3lFBkUSxlwEYsO9RMup
aKxV4FT2Pb1yBicwBK4TH1oeEXqEGy1YLEn+kAHRbgoC/5L0/LaiqrkzwzwwOIPj
uPGkacf8CIbX0qZo5EzD8kvfcYL1xhU3eT9WBmpp2ZwD+4bINd4=
=nax1
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-net is finally supported in vduse
- virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
virtio-pci: Check if is_avq is NULL
virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
MAINTAINERS: add Eugenio Pérez as reviewer
vhost-vdpa: Remove usage of the deprecated ida_simple_xx() API
vp_vdpa: don't allocate unused msix vectors
sound: virtio: drop owner assignment
fuse: virtio: drop owner assignment
scsi: virtio: drop owner assignment
rpmsg: virtio: drop owner assignment
nvdimm: virtio_pmem: drop owner assignment
wifi: mac80211_hwsim: drop owner assignment
vsock/virtio: drop owner assignment
net: 9p: virtio: drop owner assignment
net: virtio: drop owner assignment
net: caif: virtio: drop owner assignment
misc: nsm: drop owner assignment
iommu: virtio: drop owner assignment
drm/virtio: drop owner assignment
gpio: virtio: drop owner assignment
firmware: arm_scmi: virtio: drop owner assignment
...
Liao Chen