Up until now when flushing pages from the TLB on SMP OpenRISC was always
resorting to flush the entire TLB on all CPUs. This patch adds the
mechanics for flushing specific ranges and pages based on the usage.
The function switch_mm is updated to account for cpu usage by updating
mm_struct's cpumask. This is used in the SMP flush routines.
This mostly follows the riscv implementation.
Signed-off-by: Stafford Horne <shorne@gmail.com>
When dumping a stack with 'cat /proc/#/stack' the kernel would oops.
For example:
# cat /proc/690/stack
Unable to handle kernel access
at virtual address 0x7fc60f58
Oops#: 0000
CPU #: 0
PC: c00097fc SR: 0000807f SP: d6f09b9c
GPR00: 00000000 GPR01: d6f09b9c GPR02: d6f09bb8 GPR03: d6f09bc4
GPR04: 7fc60f5c GPR05: c00099b4 GPR06: 00000000 GPR07: d6f09ba3
GPR08: ffffff00 GPR09: c0009804 GPR10: d6f08000 GPR11: 00000000
GPR12: ffffe000 GPR13: dbb86000 GPR14: 00000001 GPR15: dbb86250
GPR16: 7fc60f63 GPR17: 00000f5c GPR18: d6f09bc4 GPR19: 00000000
GPR20: c00099b4 GPR21: ffffffc0 GPR22: 00000000 GPR23: 00000000
GPR24: 00000001 GPR25: 000002c6 GPR26: d78b6850 GPR27: 00000001
GPR28: 00000000 GPR29: dbb86000 GPR30: ffffffff GPR31: dbb862fc
RES: 00000000 oGPR11: ffffffff
Process cat (pid: 702, stackpage=d79d6000)
Stack:
Call trace:
[<598977f2>] save_stack_trace_tsk+0x40/0x74
[<95063f0e>] stack_trace_save_tsk+0x44/0x58
[<b557bfdd>] proc_pid_stack+0xd0/0x13c
[<a2df8eda>] proc_single_show+0x6c/0xf0
[<e5a737b7>] seq_read+0x1b4/0x688
[<2d6c7480>] do_iter_read+0x208/0x248
[<2182a2fb>] vfs_readv+0x64/0x90
This was caused by the stack trace code in save_stack_trace_tsk using
the wrong stack pointer. It was using the user stack pointer instead of
the kernel stack pointer. Fix this by using the right stack.
Also for good measure we add try_get_task_stack/put_task_stack to ensure
the task is not lost while we are walking it's stack.
Fixes: eecac38b04 ("openrisc: support framepointers and STACKTRACE_SUPPORT")
Signed-off-by: Stafford Horne <shorne@gmail.com>
In OpenRISC we set the initrd_start and initrd_end based on the symbols
we setup in vmlinux.lds.S. However, this is not needed if we use the
generic linker description in INIT_DATA_SECTION.
Removing our own initrd setup reduces code, but also the generic code
supports loading external initrd images. A bootloader can load a rootfs
image into memory and we can configure devicetree to load it with:
chosen {
bootargs = "earlycon";
stdout-path = "uart0:115200";
linux,initrd-start = < 0x08000100 >;
linux,initrd-end = < 0x08200000 >;
};
Reported-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
When booting on 32-bit machines (seen on OpenRISC) I saw this warning
with CONFIG_DEBUG_MUTEXES turned on.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:1242 __mutex_unlock_slowpath+0x328/0x3ec
DEBUG_LOCKS_WARN_ON(__owner_task(owner) != current)
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.8.0-rc1-simple-smp-00005-g2864e2171db4-dirty #179
Call trace:
[<(ptrval)>] dump_stack+0x34/0x48
[<(ptrval)>] __warn+0x104/0x158
[<(ptrval)>] ? __mutex_unlock_slowpath+0x328/0x3ec
[<(ptrval)>] warn_slowpath_fmt+0x7c/0x94
[<(ptrval)>] __mutex_unlock_slowpath+0x328/0x3ec
[<(ptrval)>] mutex_unlock+0x18/0x28
[<(ptrval)>] __cpuhp_setup_state_cpuslocked.part.0+0x29c/0x2f4
[<(ptrval)>] ? page_alloc_cpu_dead+0x0/0x30
[<(ptrval)>] ? start_kernel+0x0/0x684
[<(ptrval)>] __cpuhp_setup_state+0x4c/0x5c
[<(ptrval)>] page_alloc_init+0x34/0x68
[<(ptrval)>] ? start_kernel+0x1a0/0x684
[<(ptrval)>] ? early_init_dt_scan_nodes+0x60/0x70
irq event stamp: 0
I traced this to kernel/locking/mutex.c storing 3 bits of MUTEX_FLAGS in
the task_struct pointer (mutex.owner). There is a comment saying that
task_structs are always aligned to L1_CACHE_BYTES. This is not true for
the init_task.
On 64-bit machines this is not a problem because symbol addresses are
naturally aligned to 64-bits providing 3 bits for MUTEX_FLAGS. Howerver,
for 32-bit machines the symbol address only has 2 bits available.
Fix this by setting init_task alignment to at least L1_CACHE_BYTES.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
raw_copy_to_user()'s prototype seems to be a copy & paste of
raw_copy_from_user() and as such has the __user annotation
in the 'from' argument instead of the 'to'.
So, move the __user annotation in the prototype to the 'to'.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl8oRdgACgkQSD+KveBX
+j4/LQgAkSjNzOaS7bVDzhoYL3aBQOMIzgocJUeVi7xXH8IO1uy55mNDrKBqjxbW
dy9U9VsvV5i2V2qkkQLvHVkoDSg8Buo2Uxu4OrZHOLN0KfbFrra4VvmB1CzEBix8
FICnQaZZcE7529P04TgZ8Mo9vRb5VdJFhqED5Nvegy+y8FolEsQYbjIoDBE6wa0j
Meqa/29+XCE5FzTOjbbQWizAnRZMbkxtSSreDNgeHxke9eMSO+fmwKScng63QUfl
7nfU6dW6A0d1kHhpL5RqAFOcmkpSdqYaA3SA+/8pPT9X3yOAkxE6KTKGIixpB9JX
zQt+Wkna49jJ/JfDQB5vgww5c0HjAQ==
=j0fG
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-08-03
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree says:
====================
sfc: driver for EF100 family NICs, part 2
This series implements the data path and various other functionality
for Xilinx/Solarflare EF100 NICs.
Changed from v2:
* Improved error handling of design params (patch #3)
* Removed 'inline' from .c file in patch #4
* Don't report common stats to ethtool -S (patch #8)
Changed from v1:
* Fixed build errors on CONFIG_RFS_ACCEL=n (patch #5) and 32-bit
(patch #8)
* Dropped patch #10 (ethtool ops) as it's buggy and will need a
bigger rework to fix.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't yet have a .sriov_configure() to create them, though.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Self-tests for event and interrupt reception and NVRAM.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC stats work much the same as on EF10, with a periodic DMA to a region
specified via an MCDI.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring down the TX and RX queues at ifdown, so that we can then fini the
EVQs (otherwise the MC would return EBUSY because they're still in use).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Includes checksum offload and TSO, so declare those in our netdev features.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several parts of the EF100 architecture are parameterised (to allow
varying capabilities on FPGAs according to resource constraints), and
these parameters are exposed to the driver through a TLV-encoded
region of the BAR.
For the most part we either don't care about these values at all or
just need to sanity-check them against the driver's assumptions, but
there are a number of TSO limits which we record so that we will be
able to check against them in the TX path when handling GSO skbs.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the future, EF100 is planned to have a credit-based scheme for
handling unsolicited events, which drivers will need to use in order
to function correctly. However, current EF100 hardware does not yet
generate unsolicited events and the credit scheme has not yet been
implemented in firmware. To prevent compatibility problems later if
the current driver is used with future firmware which does implement
it, we check for the corresponding capability flag (which that
future firmware will set), and if found, we refuse to probe.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Early in EF100 development there was a different format of event
descriptor; if the NIC is somehow running the very old firmware
which will use that format, fail the probe.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls napi_schedule_irqoff() from a context where, in RT,
hardirqs are not disabled, since the IRQ handler is force-threaded.
In the call path of this function, __raise_softirq_irqoff() is modifying
its per-CPU mask of pending softirqs that must be processed, using
or_softirq_pending(). The or_softirq_pending() function is not atomic,
but since interrupts are supposed to be disabled, nobody should be
preempting it, and the operation should be safe.
Nonetheless, when running with hardirqs on, as in the PREEMPT_RT case,
it isn't safe, and the pending softirqs mask can get corrupted,
resulting in softirqs being lost and never processed.
To have common code that works with PREEMPT_RT and with mainline Linux,
we can use plain napi_schedule() instead. The difference is that
napi_schedule() (via __napi_schedule) also calls local_irq_save, which
disables hardirqs if they aren't already. But, since they already are
disabled in non-RT, this means that in practice we don't see any
measurable difference in throughput or latency with this patch.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls napi_schedule_irqoff() from a context where, in RT,
hardirqs are not disabled, since the IRQ handler is force-threaded.
In the call path of this function, __raise_softirq_irqoff() is modifying
its per-CPU mask of pending softirqs that must be processed, using
or_softirq_pending(). The or_softirq_pending() function is not atomic,
but since interrupts are supposed to be disabled, nobody should be
preempting it, and the operation should be safe.
Nonetheless, when running with hardirqs on, as in the PREEMPT_RT case,
it isn't safe, and the pending softirqs mask can get corrupted,
resulting in softirqs being lost and never processed.
To have common code that works with PREEMPT_RT and with mainline Linux,
we can use plain napi_schedule() instead. The difference is that
napi_schedule() (via __napi_schedule) also calls local_irq_save, which
disables hardirqs if they aren't already. But, since they already are
disabled in non-RT, this means that in practice we don't see any
measurable difference in throughput or latency with this patch.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: loop: Preparatory changes for 802.1Q data path
Florian Fainelli says:
====================
These patches are all meant to help pave the way for a 802.1Q data path
added to the mockup driver, making it more useful than just testing for
configuration. Sending those out now since there is no real need to
wait.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We only support DSA_LOOP_NUM_PORTS in the switch, do not tell the DSA
core to allocate up to DSA_MAX_PORTS which is nearly the double (6 vs.
11).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For now we simply store the port MTU into a per-port member.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for a mockup data path, move the
driver data structures to include/linux/dsa/loop.h such that we can
share them between net/dsa/ and drivers/net/dsa/ later on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate a 4K array of VLANs instead of limiting ourselves to just 5
which is arbitrary.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PVID should be per-port, this is a preliminary change to support a
802.1Q data path in the driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matching IPv6 traffic require allocating their own individual slots
in TCAM. So, fetch additional slots to insert IPv6 rules. Also, fetch
the cumulative stats of all the slots occupied by the Matchall rule.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current poll interval is enough to ensure that rising and falling
edge events are not lost for a 1 PPS signal with 50% duty cycle.
But when we deliver the events to user space, it will try to infer if
they were corresponding to a rising or to a falling edge (the kernel
driver doesn't know that either). User space will try to make that
inference based on the time at which the PPS master had emitted the
pulse (i.e. if it's a .0 time, it's rising edge, if it's .5 time, it's
falling edge).
But there is no in-kernel API for retrieving the precise timestamp
corresponding to a PPS master (aka perout) pulse. So user space has to
guess even that. It will read the PTP time on the PPS master right after
we've delivered the extts event, and declare that the PPS master time
was just the closest integer second, based on 2 thresholds (lower than
.25, or higher than .75, and ignore anything else).
Except that, if we poll for extts events (and our hardware doesn't
really help us, by not providing an interrupt), then there is a risk
that the poll period (and therefore the time at which the event is
delivered) might confuse user space.
Because we are always scheduling the next extts poll at
SJA1105_EXTTS_INTERVAL "from now" (that's the only thing that the
schedule_delayed_work() API gives us), it means that the start time of
the next delayed workqueue will always be shifted to the right a little
bit (shifted with the SPI access duration of this workqueue run).
In turn, because user space sees extts events that are non-periodic
compared to the PPS master's time, this means that it might start making
wrong guesses about rising/falling edge.
To understand the effect, here is the output of ts2phc currently. Notice
the 'src' timestamps of the 'SKIP extts' events, and how they have a
large wander. They keep increasing until the upper limit for the ignore
threshold (.75 seconds), after which the application starts ignoring the
_other_ edge.
ts2phc[26.624]: /dev/ptp3 SKIP extts index 0 at 21.449898912 src 21.657784518
ts2phc[27.133]: adding tstamp 21.949894240 to clock /dev/ptp3
ts2phc[27.133]: adding tstamp 22.000000000 to clock /dev/ptp1
ts2phc[27.133]: /dev/ptp3 offset 640 s2 freq +5112
ts2phc[27.636]: /dev/ptp3 SKIP extts index 0 at 22.449889360 src 22.669398022
ts2phc[28.140]: adding tstamp 22.949884376 to clock /dev/ptp3
ts2phc[28.140]: adding tstamp 23.000000000 to clock /dev/ptp1
ts2phc[28.140]: /dev/ptp3 offset 96 s2 freq +4760
ts2phc[28.644]: /dev/ptp3 SKIP extts index 0 at 23.449879504 src 23.677420422
ts2phc[29.153]: adding tstamp 23.949874704 to clock /dev/ptp3
ts2phc[29.153]: adding tstamp 24.000000000 to clock /dev/ptp1
ts2phc[29.153]: /dev/ptp3 offset -264 s2 freq +4429
ts2phc[29.656]: /dev/ptp3 SKIP extts index 0 at 24.449870008 src 24.689407238
ts2phc[30.160]: adding tstamp 24.949865376 to clock /dev/ptp3
ts2phc[30.160]: adding tstamp 25.000000000 to clock /dev/ptp1
ts2phc[30.160]: /dev/ptp3 offset -280 s2 freq +4334
ts2phc[30.664]: /dev/ptp3 SKIP extts index 0 at 25.449860760 src 25.697449926
ts2phc[31.168]: adding tstamp 25.949856176 to clock /dev/ptp3
ts2phc[31.168]: adding tstamp 26.000000000 to clock /dev/ptp1
ts2phc[31.168]: /dev/ptp3 offset -176 s2 freq +4354
ts2phc[31.672]: /dev/ptp3 SKIP extts index 0 at 26.449851584 src 26.705433606
ts2phc[32.180]: adding tstamp 26.949846992 to clock /dev/ptp3
ts2phc[32.180]: adding tstamp 27.000000000 to clock /dev/ptp1
ts2phc[32.180]: /dev/ptp3 offset -80 s2 freq +4397
ts2phc[32.684]: /dev/ptp3 SKIP extts index 0 at 27.449842384 src 27.717415110
ts2phc[33.192]: adding tstamp 27.949837768 to clock /dev/ptp3
ts2phc[33.192]: adding tstamp 28.000000000 to clock /dev/ptp1
ts2phc[33.192]: /dev/ptp3 offset 0 s2 freq +4453
ts2phc[33.696]: /dev/ptp3 SKIP extts index 0 at 28.449833128 src 28.729412902
ts2phc[34.200]: adding tstamp 28.949828472 to clock /dev/ptp3
ts2phc[34.200]: adding tstamp 29.000000000 to clock /dev/ptp1
ts2phc[34.200]: /dev/ptp3 offset 8 s2 freq +4461
ts2phc[34.704]: /dev/ptp3 SKIP extts index 0 at 29.449823816 src 29.737416038
ts2phc[35.208]: adding tstamp 29.949819152 to clock /dev/ptp3
ts2phc[35.208]: adding tstamp 30.000000000 to clock /dev/ptp1
ts2phc[35.208]: /dev/ptp3 offset -8 s2 freq +4447
ts2phc[35.712]: /dev/ptp3 SKIP extts index 0 at 30.449814496 src 30.745554982
ts2phc[36.216]: adding tstamp 30.949809840 to clock /dev/ptp3
ts2phc[36.216]: adding tstamp 31.000000000 to clock /dev/ptp1
ts2phc[36.216]: /dev/ptp3 offset -8 s2 freq +4445
ts2phc[36.468]: /dev/ptp3 SKIP extts index 0 at 31.449805184 src 31.501109446
ts2phc[36.972]: adding tstamp 31.949800536 to clock /dev/ptp3
ts2phc[36.972]: adding tstamp 32.000000000 to clock /dev/ptp1
ts2phc[36.972]: /dev/ptp3 offset -8 s2 freq +4442
ts2phc[37.480]: /dev/ptp3 SKIP extts index 0 at 32.449795896 src 32.513320070
ts2phc[37.984]: adding tstamp 32.949791248 to clock /dev/ptp3
ts2phc[37.984]: adding tstamp 33.000000000 to clock /dev/ptp1
ts2phc[37.984]: /dev/ptp3 offset 0 s2 freq +4448
Fix that by taking the following measures:
- Schedule the poll from a timer. Because we are really scheduling the
timer periodically, the extts events delivered to user space are
periodic too, and don't suffer from the "shift-to-the-right" effect.
- Increase the poll period to 6 times a second. This imposes a smaller
upper bound to the shift that can occur to the delivery time of extts
events, and makes user space (ts2phc) to always interpret correctly
which events should be skipped and which shouldn't.
- Move the SPI readout itself to the main PTP kernel thread, instead of
the generic workqueue. This is because the timer runs in atomic
context, but is also better than before, because if needed, we can
chrt & taskset this kernel thread, to ensure it gets enough priority
under load.
After this patch, one can notice that the wander is greatly reduced, and
that the latencies of one extts poll are not propagated to the next. The
'src' timestamp that is skipped is never larger than .65 seconds (which
means .15 seconds larger than the time at which the real event occurred
at, and .10 seconds smaller than the .75 upper threshold for ignoring
the falling edge):
ts2phc[40.076]: adding tstamp 34.949261296 to clock /dev/ptp3
ts2phc[40.076]: adding tstamp 35.000000000 to clock /dev/ptp1
ts2phc[40.076]: /dev/ptp3 offset 48 s2 freq +4631
ts2phc[40.568]: /dev/ptp3 SKIP extts index 0 at 35.449256496 src 35.595791078
ts2phc[41.064]: adding tstamp 35.949251744 to clock /dev/ptp3
ts2phc[41.064]: adding tstamp 36.000000000 to clock /dev/ptp1
ts2phc[41.064]: /dev/ptp3 offset -224 s2 freq +4374
ts2phc[41.552]: /dev/ptp3 SKIP extts index 0 at 36.449247088 src 36.579825574
ts2phc[42.044]: adding tstamp 36.949242456 to clock /dev/ptp3
ts2phc[42.044]: adding tstamp 37.000000000 to clock /dev/ptp1
ts2phc[42.044]: /dev/ptp3 offset -240 s2 freq +4290
ts2phc[42.536]: /dev/ptp3 SKIP extts index 0 at 37.449237848 src 37.563828774
ts2phc[43.028]: adding tstamp 37.949233264 to clock /dev/ptp3
ts2phc[43.028]: adding tstamp 38.000000000 to clock /dev/ptp1
ts2phc[43.028]: /dev/ptp3 offset -144 s2 freq +4314
ts2phc[43.520]: /dev/ptp3 SKIP extts index 0 at 38.449228656 src 38.547823238
ts2phc[44.012]: adding tstamp 38.949224048 to clock /dev/ptp3
ts2phc[44.012]: adding tstamp 39.000000000 to clock /dev/ptp1
ts2phc[44.012]: /dev/ptp3 offset -80 s2 freq +4335
ts2phc[44.508]: /dev/ptp3 SKIP extts index 0 at 39.449219432 src 39.535846118
ts2phc[44.996]: adding tstamp 39.949214816 to clock /dev/ptp3
ts2phc[44.996]: adding tstamp 40.000000000 to clock /dev/ptp1
ts2phc[44.996]: /dev/ptp3 offset -32 s2 freq +4359
ts2phc[45.488]: /dev/ptp3 SKIP extts index 0 at 40.449210192 src 40.515824678
ts2phc[45.980]: adding tstamp 40.949205568 to clock /dev/ptp3
ts2phc[45.980]: adding tstamp 41.000000000 to clock /dev/ptp1
ts2phc[45.980]: /dev/ptp3 offset 8 s2 freq +4390
ts2phc[46.636]: /dev/ptp3 SKIP extts index 0 at 41.449200928 src 41.664176902
ts2phc[47.132]: adding tstamp 41.949196288 to clock /dev/ptp3
ts2phc[47.132]: adding tstamp 42.000000000 to clock /dev/ptp1
ts2phc[47.132]: /dev/ptp3 offset 0 s2 freq +4384
ts2phc[47.620]: /dev/ptp3 SKIP extts index 0 at 42.449191656 src 42.648117190
ts2phc[48.112]: adding tstamp 42.949187016 to clock /dev/ptp3
ts2phc[48.112]: adding tstamp 43.000000000 to clock /dev/ptp1
ts2phc[48.112]: /dev/ptp3 offset 0 s2 freq +4384
ts2phc[48.604]: /dev/ptp3 SKIP extts index 0 at 43.449182384 src 43.632112582
ts2phc[49.100]: adding tstamp 43.949177736 to clock /dev/ptp3
ts2phc[49.100]: adding tstamp 44.000000000 to clock /dev/ptp1
ts2phc[49.100]: /dev/ptp3 offset -8 s2 freq +4376
ts2phc[49.588]: /dev/ptp3 SKIP extts index 0 at 44.449173096 src 44.616136774
ts2phc[50.080]: adding tstamp 44.949168464 to clock /dev/ptp3
ts2phc[50.080]: adding tstamp 45.000000000 to clock /dev/ptp1
ts2phc[50.080]: /dev/ptp3 offset 8 s2 freq +4390
ts2phc[50.572]: /dev/ptp3 SKIP extts index 0 at 45.449163816 src 45.600134662
ts2phc[51.064]: adding tstamp 45.949159160 to clock /dev/ptp3
ts2phc[51.064]: adding tstamp 46.000000000 to clock /dev/ptp1
ts2phc[51.064]: /dev/ptp3 offset -8 s2 freq +4376
ts2phc[51.556]: /dev/ptp3 SKIP extts index 0 at 46.449154528 src 46.584588550
ts2phc[52.048]: adding tstamp 46.949149896 to clock /dev/ptp3
ts2phc[52.048]: adding tstamp 47.000000000 to clock /dev/ptp1
ts2phc[52.048]: /dev/ptp3 offset 0 s2 freq +4382
ts2phc[52.540]: /dev/ptp3 SKIP extts index 0 at 47.449145256 src 47.568132198
ts2phc[53.032]: adding tstamp 47.949140616 to clock /dev/ptp3
ts2phc[53.032]: adding tstamp 48.000000000 to clock /dev/ptp1
ts2phc[53.032]: /dev/ptp3 offset 0 s2 freq +4382
ts2phc[53.524]: /dev/ptp3 SKIP extts index 0 at 48.449135968 src 48.552121446
ts2phc[54.016]: adding tstamp 48.949131320 to clock /dev/ptp3
ts2phc[54.016]: adding tstamp 49.000000000 to clock /dev/ptp1
ts2phc[54.016]: /dev/ptp3 offset 0 s2 freq +4382
ts2phc[54.512]: /dev/ptp3 SKIP extts index 0 at 49.449126680 src 49.540147014
ts2phc[55.000]: adding tstamp 49.949122040 to clock /dev/ptp3
ts2phc[55.000]: adding tstamp 50.000000000 to clock /dev/ptp1
ts2phc[55.000]: /dev/ptp3 offset 0 s2 freq +4382
ts2phc[55.492]: /dev/ptp3 SKIP extts index 0 at 50.449117400 src 50.520119078
ts2phc[55.988]: adding tstamp 50.949112768 to clock /dev/ptp3
ts2phc[55.988]: adding tstamp 51.000000000 to clock /dev/ptp1
ts2phc[55.988]: /dev/ptp3 offset 8 s2 freq +4390
ts2phc[56.476]: /dev/ptp3 SKIP extts index 0 at 51.449108120 src 51.504175910
ts2phc[57.132]: adding tstamp 51.949103480 to clock /dev/ptp3
ts2phc[57.132]: adding tstamp 52.000000000 to clock /dev/ptp1
ts2phc[57.132]: /dev/ptp3 offset 0 s2 freq +4384
ts2phc[57.624]: /dev/ptp3 SKIP extts index 0 at 52.449098840 src 52.651833574
ts2phc[58.116]: adding tstamp 52.949094200 to clock /dev/ptp3
ts2phc[58.116]: adding tstamp 53.000000000 to clock /dev/ptp1
ts2phc[58.116]: /dev/ptp3 offset 8 s2 freq +4392
ts2phc[58.612]: /dev/ptp3 SKIP extts index 0 at 53.449089560 src 53.639826918
ts2phc[59.100]: adding tstamp 53.949084920 to clock /dev/ptp3
ts2phc[59.100]: adding tstamp 54.000000000 to clock /dev/ptp1
ts2phc[59.100]: /dev/ptp3 offset 8 s2 freq +4394
ts2phc[59.592]: /dev/ptp3 SKIP extts index 0 at 54.449080272 src 54.619842278
ts2phc[60.084]: adding tstamp 54.949075624 to clock /dev/ptp3
ts2phc[60.084]: adding tstamp 55.000000000 to clock /dev/ptp1
ts2phc[60.084]: /dev/ptp3 offset 8 s2 freq +4397
ts2phc[60.576]: /dev/ptp3 SKIP extts index 0 at 55.449070968 src 55.603885542
ts2phc[61.068]: adding tstamp 55.949066312 to clock /dev/ptp3
ts2phc[61.068]: adding tstamp 56.000000000 to clock /dev/ptp1
ts2phc[61.068]: /dev/ptp3 offset 0 s2 freq +4391
ts2phc[61.560]: /dev/ptp3 SKIP extts index 0 at 56.449061680 src 56.587885798
ts2phc[62.052]: adding tstamp 56.949057032 to clock /dev/ptp3
ts2phc[62.052]: adding tstamp 57.000000000 to clock /dev/ptp1
ts2phc[62.052]: /dev/ptp3 offset -8 s2 freq +4383
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of memory pressure, mptcp_sendmsg() may call
sk_stream_wait_memory() after succesfully xmitting some
bytes. If the latter fails we currently return to the
user-space the error code, ignoring the succeful xmit.
Address the issue always checking for the xmitted bytes
before mptcp_sendmsg() completes.
Fixes: f296234c98 ("mptcp: Add handling of incoming MP_JOIN requests")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Add support for buffer drop traps
Petr says:
A recent patch set added the ability to mirror buffer related drops
(e.g., early drops) through a netdev. This patch set adds the ability to
trap such packets to the local CPU for analysis.
The trapping towards the CPU is configured by using tc-trap action
instead of tc-mirred as was done when the packets were mirrored through
a netdev. A future patch set will also add the ability to sample the
dropped packets using tc-sample action.
The buffer related drop traps are added to devlink, which means that the
dropped packets can be reported to user space via the kernel's
drop_monitor module.
Patch set overview:
Patch #1 adds the early_drop trap to devlink
Patch #2 adds extack to a few devlink operations to facilitate better
error reporting to user space. This is necessary - among other things -
because the action of buffer drop traps cannot be changed in mlxsw
Patch #3 performs a small refactoring in mlxsw, patch #4 fixes a bug that
this patchset would trigger.
Patches #5-#6 add the infrastructure required to support different traps
/ trap groups in mlxsw per-ASIC. This is required because buffer drop
traps are not supported by Spectrum-1
Patch #7 extends mlxsw to register the early_drop trap
Patch #8 adds the offload logic for the "trap" action at a qevent block.
Patch #9 adds a mlxsw-specific selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest for RED early_drop and mark qevents when a trap action is
attached at the associated block.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading action trap on a qevent, pass to_dev of NULL to the SPAN
module to trigger the mirror to the CPU port. Query the buffer drops
policer and use it for policing of the trapped traffic.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously explained, packets that are dropped due to buffer related
reasons (e.g., tail drop, early drop) can be mirrored to the CPU port.
These packets are then trapped with one of the "mirror session" traps
and their CQE includes the reason for which the packet was mirrored.
Register with devlink a new trap, early_drop, and initialize the
corresponding Rx listener with the appropriate mirror reason. Return an
error in case user tries to change the traps' action, as this is not
supported.
Since Spectrum-1 does not support these traps, the above is only done
for Spectrum-2 onwards.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches will need to register different traps for Spectrum-1
and Spectrum-2 onwards.
Enable that by invoking a per-ASIC operation during traps
initialization.
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches will need to register different trap groups for
Spectrum-1 and Spectrum-2 onwards.
Enable that by invoking a per-ASIC operation during trap groups
initialization.
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unsetting policer base, the SPAN code currently uses refcount_dec().
However that function splats when the counter reaches zero, because
reaching zero without actually testing is in general indicative of a
missing cleanup. There is no cleanup to be done here, but nonetheless, use
refcount_dec_and_test() as required.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'size_t' instead of 'u64' for array sizes, as this this is correct
type to use for expressions involving sizeof().
Suggested-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch will refuse to set the action of certain traps in mlxsw
and also to change the policer binding of certain groups. Pass extack so
that failure could be communicated clearly to user space.
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the packet trap that can report packets that were ECN marked due to RED
AQM.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current judgment condition of f2fs_bug_on in function update_sit_entry():
new_vblocks >> (sizeof(unsigned short) << 3) ||
new_vblocks > sbi->blocks_per_seg
which equivalents to:
new_vblocks < 0 || new_vblocks > sbi->blocks_per_seg
The latter is more intuitive.
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reported-by: Jack Qiu <jack.qiu@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Since set/clear_inode_flag() don't need to return value to show
if flag is set, we can just call set/clear_bit() here.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When we use F2FS_IOC_RELEASE_COMPRESS_BLOCKS ioctl, if we can't find
any compressed blocks in the file even with large file size, the
ioctl just ends up without changing the file's status as immutable.
It makes the user, who expects that the file is immutable when it
returns successfully, confused.
Signed-off-by: Daeho Jeong <daehojeong@google.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
* ASUS WMI driver honors BAT1 name of the battery
(quite a few new laptops are using it)
* Dell WMI driver supports new key codes and backlight events
* ThinkPad ACPI driver now may use standard charge threshold interface,
it also has been updated to provide Laptop or Desktop mode to the user
* Intel Speed Select Technology gained support on Sapphire Rapids platform
* Regular update of Speed Select Technology tools
* Mellanox has been updated to support complex attributes
* PMC core driver has been fixed to show correct names for LPM0 register
* HTTP links were replaced by HTTPS ones where it applies
* Miscellaneous fixes and cleanups here and there
The following is an automated git shortlog grouped by driver:
acerhdf:
- Replace HTTP links with HTTPS ones
Add new intel_atomisp2_led driver:
- Add new intel_atomisp2_led driver
apple-gmux:
- Replace HTTP links with HTTPS ones
asus-nb-wmi:
- Drop duplicate DMI quirk structures
- add support for ASUS ROG Zephyrus G14 and G15
asus-wmi:
- allow BAT1 battery name
dell-wmi:
- add new dmi mapping for keycode 0xffff
- add new keymap type 0x0012
- add new backlight events
intel_cht_int33fe:
- Drop double check for ACPI companion device
intel-hid:
- Fix return value check in check_acpi_dev()
intel_pmc_core:
- fix bound check in pmc_core_mphy_pg_show()
- update TGL's LPM0 reg bit map name
intel-vbtn:
- Fix return value check in check_acpi_dev()
ISST:
- drop a duplicated word in isst_if.h
- Add new PCI device ids
pcengines-apuv2:
- revert wiring up simswitch GPIO as LED
platform/mellanox:
- Introduce string_upper() and string_lower() helpers
- Add string_upper() and string_lower() tests
- Extend FAN platform data description
- Add more definitions for system attributes
- Add new attribute for mlxreg-io sysfs interfaces
- Add presence register field for FAN devices
- Add support for complex attributes
- mlxreg-io: Add support for complex attributes
- mlxreg-hotplug: Add environmental data to uevent
- mlxreg-hotplug: Use capability register for attribute creation
- mlxreg-hotplug: Modify module license
system76-acpi:
- Fix brightness_set schedule while atomic
thinkpad_acpi:
- Make some symbols static
- add documentation for battery charge control
- use standard charge control attribute names
- remove unused defines
- Replace HTTP links with HTTPS ones
- not loading brightness_init when _BCL invalid
- lap or desk mode interface
- Revert "Use strndup_user() in dispatch_proc_write()"
tools/power/x86/intel-speed-select:
- Update version for v5.9
- Add retries for mail box commands
- Add option to delay mbox commands
- Ignore -o option processing on error
- Change path for caching topology info
-----BEGIN PGP SIGNATURE-----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=yvnW
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.9-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- ASUS WMI driver honors BAT1 name of the battery (quite a few new
laptops are using it)
- Dell WMI driver supports new key codes and backlight events
- ThinkPad ACPI driver now may use standard charge threshold interface,
it also has been updated to provide Laptop or Desktop mode to the
user
- Intel Speed Select Technology gained support on Sapphire Rapids
platform
- Regular update of Speed Select Technology tools
- Mellanox has been updated to support complex attributes
- PMC core driver has been fixed to show correct names for LPM0
register
- HTTP links were replaced by HTTPS ones where it applies
- Miscellaneous fixes and cleanups here and there
* tag 'platform-drivers-x86-v5.9-1' of git://git.infradead.org/linux-platform-drivers-x86: (42 commits)
platform/x86: asus-nb-wmi: Drop duplicate DMI quirk structures
platform/x86: thinkpad_acpi: Make some symbols static
platform/x86: thinkpad_acpi: add documentation for battery charge control
platform/x86: thinkpad_acpi: use standard charge control attribute names
platform/x86: thinkpad_acpi: remove unused defines
platform/x86: ISST: drop a duplicated word in isst_if.h
tools/power/x86/intel-speed-select: Update version for v5.9
tools/power/x86/intel-speed-select: Add retries for mail box commands
tools/power/x86/intel-speed-select: Add option to delay mbox commands
tools/power/x86/intel-speed-select: Ignore -o option processing on error
tools/power/x86/intel-speed-select: Change path for caching topology info
platform/x86: acerhdf: Replace HTTP links with HTTPS ones
platform/x86: apple-gmux: Replace HTTP links with HTTPS ones
platform/x86: pcengines-apuv2: revert wiring up simswitch GPIO as LED
platform/x86: mlx-platform: Extend FAN platform data description
platform_data/mlxreg: Add presence register field for FAN devices
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform/mellanox: mlxreg-io: Add support for complex attributes
platform/x86: mlx-platform: Add more definitions for system attributes
platform_data/mlxreg: Add support for complex attributes
...
net/core/fib_rules.c:26:7: warning: "CONFIG_IP_MULTIPLE_TABLES" is not defined, evaluates to 0 [-Wundef]
#elif CONFIG_IP_MULTIPLE_TABLES
^~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 8b66a6fd34 ("fib: fix another fib_rules_ops indirect call wrapper problem")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-By: Brian Vazquez <brianvv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use mptcp_for_each_subflow in mptcp_stream_accept instead of
open-coding.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* handle new SAE (WPA3 authentication) status codes in the correct way
* fix a while that should be an if instead, avoiding infinite loops
* handle beacon filtering changing better
-----BEGIN PGP SIGNATURE-----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=9iOZ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few more changes, notably:
* handle new SAE (WPA3 authentication) status codes in the correct way
* fix a while that should be an if instead, avoiding infinite loops
* handle beacon filtering changing better
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With the latest net-next tree, if test suspend/resume after enabling
WOL, we get error as below:
[ 487.086365] dpm_run_callback(): mdio_bus_suspend+0x0/0x30 returns -16
[ 487.086375] PM: Device stmmac-0:00 failed to suspend: error -16
-16 means -EBUSY, this is because I didn't enable wakeup of the correct
device when implementing phy based WOL feature. To be honest, I caught
the issue when implementing phy based WOL and then fix it locally, but
forgot to amend the phy based wol patch. Today, I found the issue by
testing net-next tree.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the function seg6_lwt_headroom out of the seg6_iptunnel.h uapi
header, because it is only used in seg6_iptunnel.c. Moreover, it is only
used in the kernel code, as indicated by the "#ifdef __KERNEL__".
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Ioana-Ruxandra Stăncioi <stancioi@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stafford Horne