Currently RX and TX-completion events are unhandled, as neither the RX
nor the TX path has been implemented yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Channels are probed, but actual event handling is still stubbed out.
Stub implementation of check_caps is needed because ptp.c will call into
it from efx_ptp_use_mac_tx_timestamps() to decide if it wants TXQs.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We handle everything ourselves in ef100_reset(), rather than relying on
the generic down/up routines.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't actually do the MCDI to probe it fully until we have working
MCDI, which comes later, but we need efx->phy_data to be allocated so
that when we get MCDI events the link-state change handler doesn't
NULL-dereference.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't actually do the efx_mcdi_reset() because we don't have MCDI yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No TX or RX path, no MCDI, not even an ifup/down handler.
Besides stubs, the bulk of the patch deals with reading the Xilinx
extended PCIe capability, which tells us where to find our BAR.
Though in the same module, EF100 has its own struct pci_driver,
which is named sfc_ef100.
A small number of additional nic_type methods are added; those in the
TX (tx_enqueue) and RX (rx_packet) paths are called through indirect
call wrappers to minimise the performance impact.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EF100 adds a few new valid addresses for efx_writed_page(), as well as
a Function Control Window in the BAR whose location is variable.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An MDIO-based n-way restart does not make sense for any of the NICs
supported by this driver, nor for the coming EF100.
Unlike on Falcon (which was already split off into a separate driver),
the PHY on all of Siena, EF10 and EF100 is managed by MC firmware.
While Siena can talk to the PHY over MDIO, doing so for anything other
than debugging purposes (mdio_mii_ioctl) is likely to confuse the
firmware.
(According to the SFC firmware team, this support was originally added
to the Siena driver early in the development of that product, before
it was decided to have firmware manage the PHY.)
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of calling fsnotify() twice, once with parent inode and once
with child inode, if event should be sent to parent inode, send it
with both parent and child inodes marks in object type iterator and call
the backend handle_event() callback only once.
The parent inode is assigned to the standard "inode" iterator type and
the child inode is assigned to the special "child" iterator type.
In that case, the bit FS_EVENT_ON_CHILD will be set in the event mask,
the dir argument to handle_event will be the parent inode, the file_name
argument to handle_event is non NULL and refers to the name of the child
and the child inode can be accessed with fsnotify_data_inode().
This will allow fanotify to make decisions based on child or parent's
ignored mask. For example, when a parent is interested in a specific
event on its children, but a specific child wishes to ignore this event,
the event will not be reported. This is not what happens with current
code, but according to man page, it is the expected behavior.
Link: https://lore.kernel.org/r/20200716084230.30611-15-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
fsnotify usually calls inotify_handle_event() once for watching parent
to report event with child's name and once for watching child to report
event without child's name.
Do the same thing with a single callback instead of two callbacks when
marks iterator contains both inode and child entries.
Link: https://lore.kernel.org/r/20200716084230.30611-13-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
For some events (e.g. DN_ATTRIB on sub-directory) fsnotify may call
dnotify_handle_event() once for watching parent and once again for
the watching sub-directory.
Do the same thing with a single callback instead of two callbacks when
marks iterator contains both inode and child entries.
Link: https://lore.kernel.org/r/20200716084230.30611-12-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The fanotify_fh struct has an inline buffer of size 12 which is enough
to store the most common local filesystem file handles (e.g. ext4, xfs).
For file handles that do not fit in the inline buffer (e.g. btrfs), an
external buffer is allocated to store the file handle.
When allocating a variable size fanotify_name_event, there is no point
in allocating also an external fh buffer when file handle does not fit
in the inline buffer.
Check required size for encoding fh, preallocate an event buffer
sufficient to contain both file handle and name and store the name after
the file handle.
At this time, when not reporting name in event, we still allocate
the fixed size fanotify_fid_event and an external buffer for large
file handles, but fanotify_alloc_name_event() has already been prepared
to accept a NULL file_name.
Link: https://lore.kernel.org/r/20200716084230.30611-11-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
An fanotify event name is always recorded relative to a dir fh.
Encapsulate the name_len member of fanotify_name_event in a new struct
fanotify_info, which describes the parceling of the variable size
buffer of an fanotify_name_event.
The dir_fh member of fanotify_name_event is renamed to _dir_fh and is not
accessed directly, but via the fanotify_info_dir_fh() accessor.
Although the dir_fh len information is already available in struct
fanotify_fh, we store it also in dif_fh_totlen member of fanotify_info,
including the size of fanotify_fh header, so we know the offset of the
name in the buffer without looking inside the dir_fh.
We also add a file_fh_totlen member to allow packing another file handle
in the variable size buffer after the dir_fh and before the name.
We are going to use that space to store the child fid.
Link: https://lore.kernel.org/r/20200716084230.30611-10-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The object type iterator is used to collect all the marks of
a specific group that have interest in an event.
It is used by fanotify to get a single handle_event callback
when an event has a match to either of inode/sb/mount marks
of the group.
The nature of fsnotify events is that they are associated with
at most one sb at most one mount and at most one inode.
When a parent and child are both watching, two events are sent
to backend, one associated to parent inode and one associated
to the child inode.
This results in duplicate events in fanotify, which usually
get merged before user reads them, but this is sub-optimal.
It would be better if the same event is sent to backend with
an object type iterator that has both the child inode and its
parent, and let the backend decide if the event should be reported
once (fanotify) or twice (inotify).
Link: https://lore.kernel.org/r/20200716084230.30611-9-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Up to now, fanotify allowed to set the FAN_EVENT_ON_CHILD flag on
sb/mount marks and non-directory inode mask, but the flag was ignored.
Mask out the flag if it is provided by user on sb/mount/non-dir marks
and define it as an implicit flag that cannot be removed by user.
This flag is going to be used internally to request for events with
parent and name info.
Link: https://lore.kernel.org/r/20200716084230.30611-8-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
So far, all flags that can be set in an fanotify mark mask can be set
explicitly by a call to fanotify_mark(2).
Prepare for defining implicit event flags that cannot be set by user with
fanotify_mark(2), similar to how inotify/dnotify implicitly set the
FS_EVENT_ON_CHILD flag.
Implicit event flags cannot be removed by user and mark gets destroyed
when only implicit event flags remain in the mask.
Link: https://lore.kernel.org/r/20200716084230.30611-7-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The special event flags (FAN_ONDIR, FAN_EVENT_ON_CHILD) never had
any meaning in ignored mask. Mask them out explicitly.
Link: https://lore.kernel.org/r/20200716084230.30611-6-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
As preparation for new flags that report fids, define a bit set
of flags for a group reporting fids, currently containing the
only bit FAN_REPORT_FID.
Link: https://lore.kernel.org/r/20200716084230.30611-5-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
In fanotify_encode_fh(), both cases of NULL inode and failure to encode
ended up with fh type FILEID_INVALID.
Distiguish the case of NULL inode, by setting fh type to FILEID_ROOT.
This is just a semantic difference at this point.
Remove stale comment and unneeded check from fid event compare helpers.
Link: https://lore.kernel.org/r/20200716084230.30611-4-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
An event on directory should never be merged with an event on
non-directory regardless of the event struct type.
This change has no visible effect, because currently, with struct
fanotify_path_event, the relevant events will not be merged because
event path of dir will be different than event path of non-dir.
Link: https://lore.kernel.org/r/20200716084230.30611-3-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
In fanotify_group_event_mask() there is logic in place to make sure we
are not going to handle an event with no type and just FAN_ONDIR flag.
Generalize this logic to any FANOTIFY_EVENT_FLAGS.
There is only one more flag in this group at the moment -
FAN_EVENT_ON_CHILD. We never report it to user, but we do pass it in to
fanotify_alloc_event() when group is reporting fid as indication that
event happened on child. We will have use for this indication later on.
Link: https://lore.kernel.org/r/20200716084230.30611-2-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
It was never enabled in uapi and its functionality is about to be
superseded by events FAN_CREATE, FAN_DELETE, FAN_MOVE with group
flag FAN_REPORT_NAME.
Keep a place holder variable name_event instead of removing the
name recording code since it will be used by the new events.
Link: https://lore.kernel.org/r/20200708111156.24659-17-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Murali Karicheri says:
====================
Add PRP driver
This series is dependent on the following patches sent out to
netdev list. All (1-3) are already merged to net/master as of
sending this, but not on the net-next master branch. So need
to apply them to net-next before applying this series. v3 of
the iproute2 patches can be merged to work with this series
as there are no updates since then.
[1] https://marc.info/?l=linux-netdev&m=159526378131542&w=2
[2] https://marc.info/?l=linux-netdev&m=159499772225350&w=2
[3] https://marc.info/?l=linux-netdev&m=159499772425352&w=2
This series adds support for Parallel Redundancy Protocol (PRP)
in the Linux HSR driver as defined in IEC-62439-3. PRP Uses a
Redundancy Control Trailer (RCT) the format of which is
similar to HSR Tag. This is used for implementing redundancy.
RCT consists of 6 bytes similar to HSR tag and contain following
fields:-
- 16-bit sequence number (SeqNr);
- 4-bit LAN identifier (LanId);
- 12 bit frame size (LSDUsize);
- 16-bit suffix (PRPsuffix).
The PRPsuffix identifies PRP frames and distinguishes PRP frames
from other protocols that also append a trailer to their useful
data. The LSDUsize field allows the receiver to distinguish PRP
frames from random, nonredundant frames as an additional check.
LSDUsize is the size of the Ethernet payload inclusive of the
RCT. Sequence number along with LanId is used for duplicate
detection and discard.
PRP node is also known as Dual Attached Node (DAN-P) since it
is typically attached to two different LAN for redundancy.
DAN-P duplicates each of L2 frames and send it over the two
Ethernet links. Each outgoing frame is appended with RCT.
Unlike HSR, these are added to the end of L2 frame and will be
treated as pad by bridges and therefore would be work with
traditional bridges or switches, where as HSR wouldn't as Tag
is prefixed to the Ethenet frame. At the remote end, these are
received and the duplicate frame is discarded before the stripped
frame is send up the networking stack. Like HSR, PRP also sends
periodic Supervision frames to the network. These frames are
received and MAC address from the SV frames are populated in a
database called Node Table. The above functions are grouped into
a block called Link Redundancy Entity (LRE) in the IEC spec.
As there are many similarities between HSR and PRP protocols,
this patch re-uses the code from HSR driver to implement PRP
driver. As per feedback from the RFC series, the implementation
uses the existing HSR Netlink socket interface to create the
PRP interface by adding a new proto parameter to the ip link
command to identify the PRP protocol. iproute2 is enhanced to
implement this new parameter. The hsr_netlink.c is enhanced
to handle the new proto parameter. As suggested during the RFC
review, the driver introduced a proto_ops structure to hold
protocol specfic functions to handle HSR and PRP specific
function pointers and use them in the code based on the
protocol to handle protocol specific part differently in the
driver.
Please review this and provide me feedback so that I can work to
incorporate them and spin the next version if needed.
The patch was tested using two TI AM57x IDK boards for PRP which
are connected back to back over two CPSW Ethernet ports.
PRP Test setup
---------------
--------eth0 eth0 --------
|AM572x|----------------------|AM572x|
| |----------------------| |
--------eth1 eth1 --------
To build, enable CONFIG_HSR=y or m
make omap2plus_defconfig
make zImage; make modules; make dtbs
Copy the zImage and dtb files to the file system on SD card
and power on the AM572x boards.
This can be tested on any platforms with 2 Ethernet interfaces.
So will appreciate if you can give it a try and provide your
Tested-by.
Command to create PRP interface
-------------------------------
ifconfig eth0 0.0.0.0 down
ifconfig eth1 0.0.0.0 down
ifconfig eth0 hw ether 70:FF:76:1C:0E:8C
ifconfig eth1 hw ether 70:FF:76:1C:0E:8C
ifconfig eth0 up
ifconfig eth1 up
ip link add name prp0 type hsr slave1 eth0 slave2 eth1 supervision 45 proto 1
ifconfig prp0 192.168.2.10
ifconfig eth0 0.0.0.0 down
ifconfig eth1 0.0.0.0 down
ifconfig eth0 hw ether 70:FF:76:1C:0E:8D
ifconfig eth1 hw ether 70:FF:76:1C:0E:8D
ifconfig eth0 up
ifconfig eth1 up
ip link add name prp0 type hsr slave1 eth0 slave2 eth1 supervision 45 proto 1
ifconfig prp0 192.168.2.20
command to show node table
----------------------------
Ping the peer board after the prp0 interface is up.
The remote node (DAN-P) will be shown in the node table as below.
root@am57xx-evm:~# cat /sys/kernel/debug/hsr/prp0/node_table
Node Table entries for (PRP) device
MAC-Address-A, MAC-Address-B, time_in[A], time_in[B], Address-B port, SAN-A, SAN-B, DAN-P
70:ff:76:1c:0e:8c 00:00:00:00:00:00 ffffe83f, ffffe83f, 0, 0, 0, 1
Try to capture the raw PRP frames at the eth0 interface as
tcpdump -i eth0 -xxx
Sample Supervision frames and ARP frames shown below.
==================================================================================
Successive Supervision frames captured with tcpdump (with RCT at the end):
03:43:29.500999 70:ff:76:1c:0e:8d (oui Unknown) > 01:15:4e:00:01:2d (oui Unknown), ethertype Unknown (0x88f
0x0000: 0115 4e00 012d 70ff 761c 0e8d 88fb 0001
0x0010: 7e0a 1406 70ff 761c 0e8d 0000 0000 0000
0x0020: 0000 0000 0000 0000 0000 0000 0000 0000
0x0030: 0000 0000 0000 0000 0000 0000 fc2b a034
0x0040: 88fb
03:43:31.581025 70:ff:76:1c:0e:8d (oui Unknown) > 01:15:4e:00:01:2d (oui Unknown), ethertype Unknown (0x88f
0x0000: 0115 4e00 012d 70ff 761c 0e8d 88fb 0001
0x0010: 7e0b 1406 70ff 761c 0e8d 0000 0000 0000
0x0020: 0000 0000 0000 0000 0000 0000 0000 0000
0x0030: 0000 0000 0000 0000 0000 0000 fc2c a034
0x0040: 88fb
ICMP Echo request frame with RCT
03:43:33.805354 IP 192.168.2.20 > 192.168.2.10: ICMP echo request, id 63748, seq 1, length 64
0x0000: 70ff 761c 0e8c 70ff 761c 0e8d 0800 4500
0x0010: 0054 26a4 4000 4001 8e96 c0a8 0214 c0a8
0x0020: 020a 0800 c28e f904 0001 202e 1c3d 0000
0x0030: 0000 0000 0000 0000 0000 0000 0000 0000
0x0040: 0000 0000 0000 0000 0000 0000 0000 0000
0x0050: 0000 0000 0000 0000 0000 0000 0000 0000
0x0060: 0000 fc31 a05a 88fb
==================================================================================
The iperf3 traffic test logs can be accessed at the links below.
DUT-1: https://pastebin.ubuntu.com/p/8SkQzWJMn8/
DUT-2: https://pastebin.ubuntu.com/p/j2BZvvs7p4/
Other tests done.
- Connect a SAN (eth0 and eth1 without prp interface) and
do ping test from eth0 (192.168.2.40) to prp0 (192.168.2.10)
verify the SAN node shows at the correct link A and B as shown
in the node table dump
- Regress HSR interface using 3 nodes connected in a ring topology.
create hsr link version 0. Do iperf3 test between all nodes
create hsr link version 1. Do iperf3 test between all nodes.
--------eth0 eth1 --------eth0 eth1-------|
|AM572x|----------------------|AM572x|--------------|AM572x|
| | | | ------| |
--------eth1---| ------- | eth0 -------
|-------------------------------
command used for HSR interface
HSR V0
ifconfig eth0 0.0.0.0 down
ifconfig eth1 0.0.0.0 down
ifconfig eth0 hw ether 70:FF:76:1C:0E:8C
ifconfig eth1 hw ether 70:FF:76:1C:0E:8C
ifconfig eth0 up
ifconfig eth1 up
ip link add name hsr0 type hsr slave1 eth0 slave2 eth1 supervision 45 version 0
ifconfig hsr0 192.168.2.10
HSR V1
ifconfig eth0 0.0.0.0 down
ifconfig eth1 0.0.0.0 down
ifconfig eth0 hw ether 70:FF:76:1C:0E:8C
ifconfig eth1 hw ether 70:FF:76:1C:0E:8C
ifconfig eth0 up
ifconfig eth1 up
ip link add name hsr0 type hsr slave1 eth0 slave2 eth1 supervision 45 version 1
ifconfig hsr0 192.168.2.10
Logs at
DUT-1 : https://pastebin.ubuntu.com/p/6PSJbZwQ6y/
DUT-2 : https://pastebin.ubuntu.com/p/T8TqJsPRHc/
DUT-3 : https://pastebin.ubuntu.com/p/VNzpv6HzKj/
- Build tests :-
Build with CONFIG_HSR=m
allmodconfig build
build with CONFIG_HSR=y and rebuild with sparse checker
make C=1 zImage; make modules
Version history:
v5 : Fixed comments about Kconfig changes on Patch 1/7 against v4
Rebased to netnext/master branch.
v4 : fixed following vs v3
reverse xmas tree for local variables
check for return type in call to skb_put_padto()
v3 : Separated bug fixes from this series and send them for immediate merge
But for that this is same as v2.
v2 : updated comments on RFC. Following are the main changes:-
- Removed the hsr_prp prefix
- Added PRP information in header files to indicate
the support for PRP explicitely
- Re-use netlink socket interface with an added
parameter proto for identifying PRP.
- Use function pointers using a proto_ops struct
to do things differently for PRP vs HSR.
RFC: initial version posted and discussed at
https://www.spinics.net/lists/netdev/msg656229.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Print PRP specific information from node table as part of debugfs
node table display. Also display the node as DAN-H or DAN-P depending
on the info from node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DAN-P (Dual Attached Nodes PRP) nodes are expected to receive
traditional IP packets as well as PRP (Parallel Redundancy
Protocol) tagged (trailer) packets. PRP trailer is 6 bytes
of PRP protocol unit called RCT, Redundancy Control Trailer
(RCT) similar to HSR tag. PRP network can have traditional
devices such as bridges/switches or PC attached to it and
should be able to communicate. Regular Ethernet devices treat
the RCT as pads. This patch adds logic to format L2 frames
from network stack to add a trailer (RCT) and send it as
duplicates over the slave interfaces when the protocol is
PRP as per IEC 62439-3. At the ingress, it strips the trailer,
do duplicate detection and rejection and forward a stripped
frame up the network stack. PRP device should accept frames
from Singly Attached Nodes (SAN) and thus the driver mark
the link where the frame came from in the node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP, refactor the code specific to
handling HSR frames into separate functions and call them through
proto_ops function pointers.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for generation of PRP supervision frames. For PRP,
supervision frame format is similar to HSR version 0, but have
a PRP Redundancy Control Trailer (RCT) added and uses a different
message type, PRP_TLV_LIFE_CHECK_DD. Also update
is_supervision_frame() to include the new message type used for
PRP supervision frame.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce support for PRP protocol, add a
protocol ops ptr in the private hsr structure to hold function
pointers as some of the functions at protocol level packet
handling is different for HSR vs PRP. It is expected that PRP will
add its of set of functions for protocol handling. Modify existing
hsr_announce() function to call proto_ops->send_sv_frame() to send
supervision frame for HSR. This is expected to be different for PRP.
So introduce a ops function ptr, send_sv_frame() for the same and
initialize it to send_hsr_supervsion_frame(). Modify hsr_announce()
to call proto_ops->send_sv_frame().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP protocol support in the
driver, refactor the skb init code to a separate function.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parallel Redundancy Protocol (PRP) is another redundancy protocol
introduced by IEC 63439 standard. It is similar to HSR in many
aspects:-
- Use a pair of Ethernet interfaces to created the PRP device
- Use a 6 byte redundancy protocol part (RCT, Redundancy Check
Trailer) similar to HSR Tag.
- Has Link Redundancy Entity (LRE) that works with RCT to implement
redundancy.
Key difference is that the protocol unit is a trailer instead of a
prefix as in HSR. That makes it inter-operable with tradition network
components such as bridges/switches which treat it as pad bytes,
whereas HSR nodes requires some kind of translators (Called redbox) to
talk to regular network devices. This features allows regular linux box
to be converted to a DAN-P box. DAN-P stands for Dual Attached Node - PRP
similar to DAN-H (Dual Attached Node - HSR).
Add a comment at the header/source code to explicitly state that the
driver files also handles PRP protocol as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan reports static checker warning:
"The patch 9b6ee3cf95d3: "qed: sanitize PBL chains allocation" from Jul
23, 2020, leads to the following static checker warning:
drivers/net/ethernet/qlogic/qed/qed_chain.c:299 qed_chain_alloc_pbl()
error: uninitialized symbol 'pbl_virt'.
drivers/net/ethernet/qlogic/qed/qed_chain.c
249 static int qed_chain_alloc_pbl(struct qed_dev *cdev, struct qed_chain *chain)
250 {
251 struct device *dev = &cdev->pdev->dev;
252 struct addr_tbl_entry *addr_tbl;
253 dma_addr_t phys, pbl_phys;
254 __le64 *pbl_virt;
^^^^^^^^^^^^^^^^
[...]
271 if (chain->b_external_pbl)
272 goto alloc_pages;
^^^^^^^^^^^^^^^^ uninitialized
[...]
298 /* Fill the PBL table with the physical address of the page */
299 pbl_virt[i] = cpu_to_le64(phys);
^^^^^^^^^^^
[...]
"
This issue was introduced with commit c3a321b06a ("qed: simplify
initialization of the chains with an external PBL"), when
chain->pbl_sp.table_virt initialization was moved up to
qed_chain_init_params().
Fix it by initializing pbl_virt with an already filled chain struct field.
Fixes: c3a321b06a ("qed: simplify initialization of the chains with an external PBL")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next hw timestamp should be snapshoot to the read registers
only once the current timestamp has been read.
If none of the pending skbs matches the current HW timestamp
just gracefully flush the available timestamp by reading it.
Signed-off-by: laurent brando <laurent.brando@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to other G12B devices using the W400 dtsi, I see reports of mmc0
tuning errors on VIM3 after a few hours uptime:
[12483.917391] mmc0: tuning execution failed: -5
[30535.551221] mmc0: tuning execution failed: -5
[35359.953671] mmc0: tuning execution failed: -5
[35561.875332] mmc0: tuning execution failed: -5
[61733.348709] mmc0: tuning execution failed: -5
I do not see the same on VIM3L, so remove sd-uhs-sdr50 from the common dtsi
to silence the error, then (re)add it to the VIM3L dts.
Fixes: 4f26cc1c96 ("arm64: dts: khadas-vim3: move common nodes into meson-khadas-vim3.dtsi")
Fixes: 700ab8d839 ("arm64: dts: khadas-vim3: add support for the SM1 based VIM3L")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200721015950.11816-1-christianshewitt@gmail.com
Unblocking sockets used for outgoing connections were not containing
inet info about the initial connection due to a typo there: the value of
"err" variable is negative in the kernelspace.
This fixes the creation of additional subflows where the remote port has
to be reused if the other host didn't announce another one. This also
fixes inet_diag showing blank info about MPTCP sockets from unblocking
sockets doing a connect().
Fixes: 41be81a8d3 ("mptcp: fix unblocking connect()")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en update.
This patchset removes the PCIe histogram and other debug register
data from ethtool -S. The removed data are not counters and they have
very large and constantly fluctuating values that are not suitable for
the ethtool -S decimal counter display.
The rest of the patches implement counter rollover for all hardware
counters that are not 64-bit counters. Different generations of
hardware have different counter widths. The driver will now query
the counter widths of all counters from firmware and implement
rollover support on all non-64-bit counters.
The last patch adds the PCIe histogram and other PCIe register data back
using the ethtool -d interface.
v2: Fix bnxt_re RDMA driver compile issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to dump PXP registers and PCIe statistics.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we can report all the full 64-bit CPU endian software accumulated
counters instead of the hw counters, some of which may be less than
64-bit wide. Define the necessary macros to access the software
counters.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the infrastructure in place, add the new function
bnxt_accumulate_all_stats() to periodically accumulate and check for
counter rollover of all ring stats and port stats.
A chip bug was also discovered that could cause some ring counters to
become 0 during DMA. Workaround by ignoring zeros on the affected
chips.
Some older frimware will reset port counters during ifdown. We need
to check for that and free the accumulated port counters during ifdown
to prevent bogus counter overflow detection during ifup.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If supported by newer firmware, make the firmware call to query all
the port counter masks. If not supported, assume 40-bit port
counter masks.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware has a new call HWRM_FUNC_QSTATS_EXT to retrieve the
masks of all ring counters. Make this call when supported to
initialize the hardware masks of all ring counters. If the call
is not available, assume 48-bit ring counter masks on P5 chips.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of these DMAed hardware counters are not full 64-bit counters and
so we need to accumulate them as they overflow. Allocate copies of these
DMA statistics memory blocks with the same size for accumulation. The
hardware counter widths are also counter specific so we allocate
memory for masks that correspond to each counter.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver manages multiple statistics structures of different sizes.
They are all allocated, freed, and handled practically the same. Define
a new bnxt_stats_mem structure and common allocation and free functions
for all staistics memory blocks.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port statistics structures have hard coded padding and offset.
Define macros to make this look cleaner.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main changes are 200G support and fixing the definitions of discard and
error counters to match the hardware definitions.
Because the HWRM_PORT_PHY_QCFG message size has now exceeded the max.
encapsulated response message size of 96 bytes from the PF to the VF,
we now need to cap this message to 96 bytes for forwarding. The forwarded
response only needs to contain the basic link status and speed information
and can be capped without adding the new information.
v2: Fix bnxt_re compile error.
Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove PCIe non-counters display from ethtool statistics, as
they are not simple counters but register dump. The next few
patches will add logic to detect counter roll-over and it won't
work with these PCIe non-counters.
There will be a follow up patch to get PCIe information via
ethtool register dump.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPLS has no dependency with the device type of underlying devices.
Hence the device type check to add mpls support for devices can be
avoided.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree