Device list is not stored in mlx5_priv anymore, so delete it as it's not
used.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Previous patch in series that implements stack devices RX path implements
indirect table rules that match on tunnel VNI. After such rule is created
all tunnel traffic is recirculated to root table. However, recirculated
packet might not match on any rules installed in the table (for example,
when IP traffic follows ARP traffic). In that case packets appear on
representor of tunnel endpoint VF instead being redirected to the VF
itself.
Extend slow table with additional flow group that matches on reg_c0 (source
port value set by indirect tables implemented by previous patch in series)
and reg_c1 (special 0xFFF mark). When creating offloads fdb tables, install
one rule per VF vport to match on recirculated miss packets and redirect
them to appropriate VF vport. Modify indirect tables code to also rewrite
reg_c1 with special 0xFFF mark.
Implementation reuses reg_c1 tunnel id bits. This is safe to do because
recirculated packets are always matched before decapsulation.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patch in series uses reg_c1 in eswitch code. To use reg_c1
helpers in both TC and eswitch code, refactor existing helpers according to
similar use case of reg_c0 and move the functionality into eswitch.h.
Calculate reg mappings length from new defines to ensure that they are
always in sync and only need to be changed in single place.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When tunnel endpoint is on VF, driver still assumes that endpoint is on
uplink and incorrectly configures encap rule offload according to that
assumption. As a result, traffic is sent directly to the uplink and rules
installed on representor of tunnel endpoint VF are ignored.
Implement following changes to allow offloading tx traffic with tunnel
endpoint on VF:
- For tunneling flows perform route lookup on route and out devices pair.
If out device is uplink and route device is VF of same physical port, then
modify packet reg_c_0 metadata register (source port) with the value of VF
vport. Use eswitch vhca_id->vport mapping introduced in one of previous
patches in the series to obtain vport from route netdevice.
- Recirculate encapsulated packets to VF vport in order to apply any flow
rules installed on VF representor that match on encapsulated traffic.
Only enable support for this functionality when all following conditions
are true:
- Hardware advertises capability to preserve reg_c_0 value on packet
recirculation.
- Vport metadata matching is enabled.
- Termination tables are to be used by the flow.
Example TC rules for VF tunnel traffic:
1. Rule that redirects packets from UL to VF rep that has the tunnel
endpoint IP address:
$ tc -s filter show dev enp8s0f0 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac 16:c9:a0:2d:69:2c
src_mac 0c:42:a1:58:ab:e4
eth_type ipv4
ip_flags nofrag
in_hw in_hw_count 1
action order 1: mirred (Egress Redirect to device enp8s0f0_0) stolen
index 3 ref 1 bind 1 installed 377 sec used 0 sec
Action statistics:
Sent 114096 bytes 952 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 114096 bytes 952 pkt
backlog 0b 0p requeues 0
cookie 878fa48d8c423fc08c3b6ca599b50a97
no_percpu
used_hw_stats delayed
2. Rule that decapsulates the tunneled flow and redirects to destination VF
representor:
$ tc -s filter show dev vxlan_sys_4789 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac ca:2e:a7:3f:f5:0f
src_mac 0a:40:bd:30:89:99
eth_type ipv4
enc_dst_ip 7.7.7.5
enc_src_ip 7.7.7.1
enc_key_id 98
enc_dst_port 4789
enc_tos 0
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key unset pipe
index 2 ref 1 bind 1 installed 434 sec used 434 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device enp8s0f0_1) stolen
index 4 ref 1 bind 1 installed 434 sec used 0 sec
Action statistics:
Sent 129936 bytes 1082 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 129936 bytes 1082 pkt
backlog 0b 0p requeues 0
cookie ac17cf398c4c69e4a5b2f7aabd1b88ff
no_percpu
used_hw_stats delayed
Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Parav Pandit Says:
=================
This patchset introduces support for mlx5 subfunction (SF).
A subfunction is a lightweight function that has a parent PCI function on
which it is deployed. mlx5 subfunction has its own function capabilities
and its own resources. This means a subfunction has its own dedicated
queues(txq, rxq, cq, eq). These queues are neither shared nor stolen from
the parent PCI function.
When subfunction is RDMA capable, it has its own QP1, GID table and rdma
resources neither shared nor stolen from the parent PCI function.
A subfunction has dedicated window in PCI BAR space that is not shared
with the other subfunctions or parent PCI function. This ensures that all
class devices of the subfunction accesses only assigned PCI BAR space.
A Subfunction supports eswitch representation through which it supports tc
offloads. User must configure eswitch to send/receive packets from/to
subfunction port.
Subfunctions share PCI level resources such as PCI MSI-X IRQs with
their other subfunctions and/or with its parent PCI function.
Patch summary:
--------------
Patch 1 to 4 prepares devlink
patch 5 to 7 mlx5 adds SF device support
Patch 8 to 11 mlx5 adds SF devlink port support
Patch 12 and 14 adds documentation
Patch-1 prepares code to handle multiple port function attributes
Patch-2 introduces devlink pcisf port flavour similar to pcipf and pcivf
Patch-3 adds port add and delete driver callbacks
Patch-4 adds port function state get and set callbacks
Patch-5 mlx5 vhca event notifier support to distribute subfunction
state change notification
Patch-6 adds SF auxiliary device
Patch-7 adds SF auxiliary driver
Patch-8 prepares eswitch to handler SF vport
Patch-9 adds eswitch helpers to add/remove SF vport
Patch-10 implements devlink port add/del callbacks
Patch-11 implements devlink port function get/set callbacks
Patch-12 to 14 adds documentation
Patch-12 added mlx5 port function documentation
Patch-13 adds subfunction documentation
Patch-14 adds mlx5 subfunction documentation
Subfunction support is discussed in detail in RFC [1] and [2].
RFC [1] and extension [2] describes requirements, design and proposed
plumbing using devlink, auxiliary bus and sysfs for systemd/udev
support. Functionality of this patchset is best explained using real
examples further below.
overview:
--------
A subfunction can be created and deleted by a user using devlink port
add/delete interface.
A subfunction can be configured using devlink port function attribute
before its activated.
When a subfunction is activated, it results in an auxiliary device on
the host PCI device where it is deployed. A driver binds to the
auxiliary device that further creates supported class devices.
example subfunction usage sequence:
-----------------------------------
Change device to switchdev mode:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Add a devlink port of subfunction flavour:
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
Configure mac address of the port function:
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88
Now activate the function:
$ devlink port function set ens2f0npf0sf88 state active
Now use the auxiliary device and class devices:
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ ip link show
127: ens2f0np0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 24:8a:07:b3:d1:12 brd ff:ff:ff:ff:ff:ff
altname enp6s0f0np0
129: p0sf88: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 00:00:00:00:88:88 brd ff:ff:ff:ff:ff:ff
$ rdma dev show
43: rdmap6s0f0: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d112 sys_image_guid 248a:0703:00b3:d112
44: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
After use inactivate the function:
$ devlink port function set ens2f0npf0sf88 state inactive
Now delete the subfunction port:
$ devlink port del ens2f0npf0sf88
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
[2] https://marc.info/?l=linux-netdev&m=158555928517777&w=2
=================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmALKDwACgkQSD+KveBX
+j7qjQf6A1moPhhIlXROCzaJUjlAj2U291LWBveU+I6na6fjYjAAWHYwfv0YKQpo
Qb0NRt+9abgEpGidc4hOwIJKhK+vlWrQuehRt83aAfAwaN3OEeGuNllniWo821Hj
sNiJfSC/DslOlQSxKLsAs3Fduy/sV3GN9Zv7hEwOFgEr5QvB2c6H1XiypVP2Ecsd
ZXC3SuEWxIoRtfXEkTkJne9LNoiDChlvT1FR/z75h8HUBdAOjzBTQzBbM+8M4Msw
8aKUPya3FMRAPWsOgPhkpU0xTtH2Mi7MC9TlwiWmrK4Q3uvesIav8pVf7r3GNAZA
sipIZ4gP0M5SiCaZa8rIBpTXBHxmvg==
=jEG4
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 subfunction support
Parav Pandit says:
This patchset introduces support for mlx5 subfunction (SF).
A subfunction is a lightweight function that has a parent PCI function on
which it is deployed. mlx5 subfunction has its own function capabilities
and its own resources. This means a subfunction has its own dedicated
queues(txq, rxq, cq, eq). These queues are neither shared nor stolen from
the parent PCI function.
When subfunction is RDMA capable, it has its own QP1, GID table and rdma
resources neither shared nor stolen from the parent PCI function.
A subfunction has dedicated window in PCI BAR space that is not shared
with the other subfunctions or parent PCI function. This ensures that all
class devices of the subfunction accesses only assigned PCI BAR space.
A Subfunction supports eswitch representation through which it supports tc
offloads. User must configure eswitch to send/receive packets from/to
subfunction port.
Subfunctions share PCI level resources such as PCI MSI-X IRQs with
their other subfunctions and/or with its parent PCI function.
Subfunction support is discussed in detail in RFC [1] and [2].
RFC [1] and extension [2] describes requirements, design and proposed
plumbing using devlink, auxiliary bus and sysfs for systemd/udev
support. Functionality of this patchset is best explained using real
examples further below.
overview:
--------
A subfunction can be created and deleted by a user using devlink port
add/delete interface.
A subfunction can be configured using devlink port function attribute
before its activated.
When a subfunction is activated, it results in an auxiliary device on
the host PCI device where it is deployed. A driver binds to the
auxiliary device that further creates supported class devices.
example subfunction usage sequence:
-----------------------------------
Change device to switchdev mode:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Add a devlink port of subfunction flavour:
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
Configure mac address of the port function:
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88
Now activate the function:
$ devlink port function set ens2f0npf0sf88 state active
Now use the auxiliary device and class devices:
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ ip link show
127: ens2f0np0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 24:8a:07:b3:d1:12 brd ff:ff:ff:ff:ff:ff
altname enp6s0f0np0
129: p0sf88: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 00:00:00:00:88:88 brd ff:ff:ff:ff:ff:ff
$ rdma dev show
43: rdmap6s0f0: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d112 sys_image_guid 248a:0703:00b3:d112
44: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
After use inactivate the function:
$ devlink port function set ens2f0npf0sf88 state inactive
Now delete the subfunction port:
$ devlink port del ens2f0npf0sf88
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
[2] https://marc.info/?l=linux-netdev&m=158555928517777&w=2
=================
* tag 'mlx5-updates-2021-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Add devlink subfunction port documentation
devlink: Extend devlink port documentation for subfunctions
devlink: Add devlink port documentation
net/mlx5: SF, Port function state change support
net/mlx5: SF, Add port add delete functionality
net/mlx5: E-switch, Add eswitch helpers for SF vport
net/mlx5: E-switch, Prepare eswitch to handle SF vport
net/mlx5: SF, Add auxiliary device driver
net/mlx5: SF, Add auxiliary device support
net/mlx5: Introduce vhca state event notifier
devlink: Support get and set state of port function
devlink: Support add and delete devlink port
devlink: Introduce PCI SF port flavour and port attribute
devlink: Prepare code to fill multiple port function attributes
====================
Link: https://lore.kernel.org/r/20210122193658.282884-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce mlx5e_trap which includes a dedicated RQ and NAPI for trapped
packets. Trap-RQ processes packets that were destined to be dropped,
but for debug and visibility sake these packets are trapped and reported
to devlink.
Trap-RQ connects between the HW and the driver and is not a part of a
channel. Open mlx5e_create_rq() and mlx5_core_destroy_rq() as API and
add dedicate RQ handlers which report to devlink of trapped packets.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to allow mlx5 core driver to trigger synchronous operations to
its consumers, add a blocking events handler. Add wrappers to
blocking_notifier_[call_chain/chain_register/chain_unregister]. Add trap
callback for action set and notify about this change. Following patches
in the set add a listener for this event.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit adds support for HTB offload in the mlx5e driver.
Performance:
NIC: Mellanox ConnectX-6 Dx
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (24 cores with HT)
100 Gbit/s line rate, 500 UDP streams @ ~200 Mbit/s each
48 traffic classes, flower used for steering
No shaping (rate limits set to 4 Gbit/s per TC) - checking for max
throughput.
Baseline: 98.7 Gbps, 8.25 Mpps
HTB: 6.7 Gbps, 0.56 Mpps
HTB offload: 95.6 Gbps, 8.00 Mpps
Limitations:
1. 256 leaf nodes, 3 levels of depth.
2. Granularity for ceil is 1 Mbit/s. Rates are converted to weights, and
the bandwidth is split among the siblings according to these weights.
Other parameters for classes are not supported.
Ethtool statistics support for QoS SQs are also added. The counters are
called qos_txN_*, where N is the QoS queue number (starting from 0, the
numeration is separate from the normal SQs), and * is the counter name
(the counters are the same as for the normal SQs).
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To handle SF port management outside of the eswitch as independent
software layer, introduce eswitch notifier APIs so that mlx5 upper
layer who wish to support sf port management in switchdev mode can
perform its task whenever eswitch mode is set to switchdev or before
eswitch is disabled.
Initialize sf port table on such eswitch event.
Add SF port add and delete functionality in switchdev mode.
Destroy all SF ports when eswitch is disabled.
Expose SF port add and delete to user via devlink commands.
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:06:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show ens2f0npf0sf88
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
or by its unique port index:
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show ens2f0npf0sf88 -jp
{
"port": {
"pci/0000:06:00.0/32768": {
"type": "eth",
"netdev": "ens2f0npf0sf88",
"flavour": "pcisf",
"controller": 0,
"pfnum": 0,
"sfnum": 88,
"external": false,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:00:00",
"state": "inactive",
"opstate": "detached"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add auxiliary device driver for mlx5 subfunction auxiliary device.
A mlx5 subfunction is similar to PCI PF and VF. For a subfunction
an auxiliary device is created.
As a result, when mlx5 SF auxiliary device binds to the driver,
its netdev and rdma device are created, they appear as
$ ls -l /sys/bus/auxiliary/devices/
mlx5_core.sf.4 -> ../../../devices/pci0000:00/0000:00:03.0/0000:06:00.0/mlx5_core.sf.4
$ ls -l /sys/class/net/eth1/device
/sys/class/net/eth1/device -> ../../../mlx5_core.sf.4
$ cat /sys/bus/auxiliary/devices/mlx5_core.sf.4/sfnum
88
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ devlink port show auxiliary/mlx5_core.sf.4/1
auxiliary/mlx5_core.sf.4/1: type eth netdev p0sf88 flavour virtual port 0 splittable false
$ rdma link show mlx5_0/1
link mlx5_0/1 state ACTIVE physical_state LINK_UP netdev p0sf88
$ rdma dev show
8: rocep6s0f1: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d113 sys_image_guid 248a:0703:00b3:d112
13: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
In future, devlink device instance name will adapt to have sfnum
annotation using either an alias or as devlink instance name described
in RFC [1].
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Introduce API to add and delete an auxiliary device for an SF.
Each SF has its own dedicated window in the PCI BAR 2.
SF device is similar to PCI PF and VF that supports multiple class of
devices such as net, rdma and vdpa.
SF device will be added or removed in subsequent patch during SF
devlink port function state change command.
A subfunction device exposes user supplied subfunction number which will
be further used by systemd/udev to have deterministic name for its
netdevice and rdma device.
An mlx5 subfunction auxiliary device example:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:08:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show ens2f0npf0sf88
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:88:88 state inactive opstate detached
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88 state active
On activation,
$ ls -l /sys/bus/auxiliary/devices/
mlx5_core.sf.4 -> ../../../devices/pci0000:00/0000:00:03.0/0000:06:00.0/mlx5_core.sf.4
$ cat /sys/bus/auxiliary/devices/mlx5_core.sf.4/sfnum
88
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
vhca state events indicates change in the state of the vhca that may
occur due to a SF allocation, deallocation or enabling/disabling the
SF HCA.
Introduce vhca state event handler which will be used by SF devlink
port manager and SF hardware id allocator in subsequent patches
to act on the event.
This enables single entity to subscribe, query and rearm the event
for a function.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This reverts commit fbdd0049d9.
Due to commit in fixes tag, netdevice events were received only in one net
namespace of mlx5_core_dev. Due to this when netdevice events arrive in
net namespace other than net namespace of mlx5_core_dev, they are missed.
This results in empty GID table due to RDMA device being detached from its
net device.
Hence, revert back to receive netdevice events in all net namespaces to
restore back RDMA functionality in non init_net net namespace. The
deadlock will have to be addressed in another patch.
Fixes: fbdd0049d9 ("RDMA/mlx5: Fix devlink deadlock on net namespace deletion")
Link: https://lore.kernel.org/r/20210117092633.10690-1-leon@kernel.org
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Add capability bit to test whether reg_c value is preserved on
recirculation.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose firmware indication that it supports setting eswitch uplink state
to follow (follow the physical link). Condition setting the eswitch
uplink admin-state with this capability bit. Older FW may not support
the uplink state setting.
Fixes: 7d0314b11c ("net/mlx5e: Modify uplink state on interface up/down")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
MLX5_GENERAL_OBJECT_TYPES types bitfield is 64-bit field.
Defining an enum for such bit fields on 32-bit platform results in below
warning.
./include/vdso/bits.h:7:26: warning: left shift count >= width of type [-Wshift-count-overflow]
^
./include/linux/mlx5/mlx5_ifc.h:10716:46: note: in expansion of macro ‘BIT’
MLX5_HCA_CAP_GENERAL_OBJECT_TYPES_SAMPLER = BIT(0x20),
^~~
Use 32-bit friendly BIT_ULL macro.
Fixes: 2a29708916 ("net/mlx5: Add sample offload hardware bits and structures")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20201213120641.216032-1-leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
mlx5-next auxbus support
This pull request is targeting net-next and rdma-next branches.
This series provides mlx5 support for auxiliary bus devices.
It starts with a merge commit of tag 'auxbus-5.11-rc1' from
gregkh/driver-core into mlx5-next, then the mlx5 patches that will convert
mlx5 ulp devices (netdev, rdma, vdpa) to use the proper auxbus
infrastructure instead of the internal mlx5 device and interface management
implementation, which Leon is deleting at the end of this patchset.
Link: https://lore.kernel.org/alsa-devel/20201026111849.1035786-1-leon@kernel.org/
Thanks to everyone for the joint effort !
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
RDMA/mlx5: Remove IB representors dead code
net/mlx5: Simplify eswitch mode check
net/mlx5: Delete custom device management logic
RDMA/mlx5: Convert mlx5_ib to use auxiliary bus
net/mlx5e: Connect ethernet part to auxiliary bus
vdpa/mlx5: Connect mlx5_vdpa to auxiliary bus
net/mlx5: Register mlx5 devices to auxiliary virtual bus
vdpa/mlx5: Make hardware definitions visible to all mlx5 devices
net/mlx5_core: Clean driver version and name
net/mlx5: Properly convey driver version to firmware
driver core: auxiliary bus: minor coding style tweaks
driver core: auxiliary bus: make remove function return void
driver core: auxiliary bus: move slab.h from include file
Add auxiliary bus support
====================
Link: https://lore.kernel.org/r/20201207053349.402772-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide mlx5_core device instead of "priv" pointer while checking
eswith mode.
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
After conversion to use auxiliary bus, all custom device management is
not needed anymore, delete it.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Move mlx5_vdpa IFC header file to the general include folder, so
mlx5_core will be able to reuse it to check if VDPA is supported
prior to creating an auxiliary device.
As part of this move, update the header file name to mlx5 general
naming scheme.
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Remove exposed driver version as it was done in other drivers,
so module version will work correctly by displaying the kernel
version for which it is compiled.
And move mlx5_core module name to general include, so auxiliary drivers
will be able to use it as a basis for a name in their device ID tables.
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
STEs format for Connect-X5 and Connect-X6DX different. Currently, on
Connext-X6DX the SW steering would break at some point when building STEs
w/o giving a proper error message. Fix this by checking the STE format of
the current device when initializing domain: add mlx5_ifc definitions for
Connect-X6DX SW steering, read FW capability to get the current format
version, and check this version when domain is being created.
Fixes: 26d688e33f ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Low level mlx5 updates required by both netdev and rdma trees:
net/mlx5: Treat host PF vport as other (non eswitch manager) vport
net/mlx5: Enable host PF HCA after eswitch is initialized
net/mlx5: Rename peer_pf to host_pf
net/mlx5: Make API mlx5_core_is_ecpf accept const pointer
net/mlx5: Export steering related functions
net/mlx5: Expose other function ifc bits
net/mlx5: Expose IP-in-IP TX and RX capability bits
net/mlx5: Update the hardware interface definition for vhca state
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Avoid exposing driver internal command helpers
net/mlx5: Add ts_cqe_to_dest_cqn related bits
net/mlx5: Add misc4 to mlx5_ifc_fte_match_param_bits
net/mlx5: Check dr mask size against mlx5_match_param size
net/mlx5: Add sampler destination type
net/mlx5: Add sample offload hardware bits and structures
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl/IOZcACgkQSD+KveBX
+j4J8wgAuxwflrYrbCWXV7LE08J7T7ZHRDE+jEbaZ0Zp9mOsYDDpcifpKwy2EVRf
RKcpMYh/GzAljmEpeWIAlMxmlpXhKWXTDruWCx73r1jvdXf/RU24/zQHa6BjeiDo
rMB8bgiW4a66+z4LcN/U6ahbVM5gScBNEt2sS1OIi9ZInngGVo9FgfhYMpERPNcH
3+mcHulCnGBNbbLwoTllOcgbxexn+xoByukg5Z0ddBJp007DMjzBIWDpDS0y2HaT
jGo1LYONgRc3zoGVmdeu9F+tSsWBIgsaiyGxKj1T/8sZUaNz2TKj9VOiYIj9BLff
cp6GRc88k7HWA4tImSHQiLbK6cx+yA==
=mjvI
-----END PGP SIGNATURE-----
Merge tag 'mlx5-next-2020-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-next-2020-12-02
Low level mlx5 updates required by both netdev and rdma trees.
* tag 'mlx5-next-2020-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Treat host PF vport as other (non eswitch manager) vport
net/mlx5: Enable host PF HCA after eswitch is initialized
net/mlx5: Rename peer_pf to host_pf
net/mlx5: Make API mlx5_core_is_ecpf accept const pointer
net/mlx5: Export steering related functions
net/mlx5: Expose other function ifc bits
net/mlx5: Expose IP-in-IP TX and RX capability bits
net/mlx5: Update the hardware interface definition for vhca state
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Avoid exposing driver internal command helpers
net/mlx5: Add ts_cqe_to_dest_cqn related bits
net/mlx5: Add misc4 to mlx5_ifc_fte_match_param_bits
net/mlx5: Check dr mask size against mlx5_match_param size
net/mlx5: Add sampler destination type
net/mlx5: Add sample offload hardware bits and structures
====================
Link: https://lore.kernel.org/r/20201203011010.213440-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When eswitch manager is running on ECPF, host PF should be treated
as non eswitch manager port, similar to other VF vports.
Fail to do so, results in firmware treating PF's vport as ECPF
vport for eswitch ACL tables.
Non zero check to figure out if a given vport is other vport or not
is not sufficient becase PF vport number = 0 on ECPF.
Hence, create esw acl tables with an attribute of other vport.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
To match the hardware spec, rename peer_pf to host_pf.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Subsequent patch implements helper API which has mlx5_core_dev
as const pointer, make its caller API too const *.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Expose other function ifc bits to enable setting HCA caps on behalf of
other function.
In addition, expose vhca_resource_manager bit to control whether the
other function functionality is supported by firmware.
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Expose FW indication that it supports stateless offloads for IP over IP
tunneled packets per direction. In some HW like ConnectX-4 IP-in-IP
support is not symmetric, it supports steering on the inner header but
it doesn't TX-Checksum and TSO. Add IP-in-IP capability per direction to
cover this case as well.
Note: only if both indications are turned on, the global
tunnel_stateless_ip_over_ip is on too.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Update the hardware interface definitions to query and modify vhca
state, related EQE and event code.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5 command init and cleanup routines are internal to mlx5_core driver.
Hence, avoid exporting them and move their definition to mlx5_core
driver's internal file mlx5_core.h
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a bit in HCA capabilities layout to indicate if ts_cqe_to_dest_cqn is
supported.
In addition, add ts_cqe_to_dest_cqn field to SQ context, for driver to
set the actual CQN.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add misc4 match params to enable matching on prog_sample_fields.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The flow sampler object is a new destination type. Add a new member
for the flow destination.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Hardware introduces flow sampler object for packet sampling.
Add the offload hardware bits and structures.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Hi Linus,
Please, pull the following patches that replace zero-length arrays with
flexible-array members.
Thanks
--
Gustavo
-----BEGIN PGP SIGNATURE-----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=vyu3
-----END PGP SIGNATURE-----
Merge tag 'flexible-array-conversions-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull more flexible-array member conversions from Gustavo A. R. Silva:
"Replace zero-length arrays with flexible-array members"
* tag 'flexible-array-conversions-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
printk: ringbuffer: Replace zero-length array with flexible-array member
net/smc: Replace zero-length array with flexible-array member
net/mlx5: Replace zero-length array with flexible-array member
mei: hw: Replace zero-length array with flexible-array member
gve: Replace zero-length array with flexible-array member
Bluetooth: btintel: Replace zero-length array with flexible-array member
scsi: target: tcmu: Replace zero-length array with flexible-array member
ima: Replace zero-length array with flexible-array member
enetc: Replace zero-length array with flexible-array member
fs: Replace zero-length array with flexible-array member
Bluetooth: Replace zero-length array with flexible-array member
params: Replace zero-length array with flexible-array member
tracepoint: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_proto: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_commands: Replace zero-length array with flexible-array member
mailbox: zynqmp-ipi-message: Replace zero-length array with flexible-array member
dmaengine: ti-cppi5: Replace zero-length array with flexible-array member
When a mlx5 core devlink instance is reloaded in different net namespace,
its associated IB device is deleted and recreated.
Example sequence is:
$ ip netns add foo
$ devlink dev reload pci/0000:00:08.0 netns foo
$ ip netns del foo
mlx5 IB device needs to attach and detach the netdevice to it through the
netdev notifier chain during load and unload sequence. A below call graph
of the unload flow.
cleanup_net()
down_read(&pernet_ops_rwsem); <- first sem acquired
ops_pre_exit_list()
pre_exit()
devlink_pernet_pre_exit()
devlink_reload()
mlx5_devlink_reload_down()
mlx5_unload_one()
[...]
mlx5_ib_remove()
mlx5_ib_unbind_slave_port()
mlx5_remove_netdev_notifier()
unregister_netdevice_notifier()
down_write(&pernet_ops_rwsem);<- recurrsive lock
Hence, when net namespace is deleted, mlx5 reload results in deadlock.
When deadlock occurs, devlink mutex is also held. This not only deadlocks
the mlx5 device under reload, but all the processes which attempt to
access unrelated devlink devices are deadlocked.
Hence, fix this by mlx5 ib driver to register for per net netdev notifier
instead of global one, which operats on the net namespace without holding
the pernet_ops_rwsem.
Fixes: 4383cfcc65 ("net/mlx5: Add devlink reload")
Link: https://lore.kernel.org/r/20201026134359.23150-1-parav@nvidia.com
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The typical set of driver updates across the subsystem:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma, hns,
usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where MRA
wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail at
the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist
-----BEGIN PGP SIGNATURE-----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=LKpl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A usual cycle for RDMA with a typical mix of driver and core subsystem
updates:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma,
hns, usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where
MRA wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail
at the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using
it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (191 commits)
RDMA/ucma: Fix use after free in destroy id flow
RDMA/rxe: Handle skb_clone() failure in rxe_recv.c
RDMA/rxe: Move the definitions for rxe_av.network_type to uAPI
RDMA: Explicitly pass in the dma_device to ib_register_device
lib/scatterlist: Do not limit max_segment to PAGE_ALIGNED values
IB/mlx4: Convert rej_tmout radix-tree to XArray
RDMA/rxe: Fix bug rejecting all multicast packets
RDMA/rxe: Fix skb lifetime in rxe_rcv_mcast_pkt()
RDMA/rxe: Remove duplicate entries in struct rxe_mr
IB/hfi,rdmavt,qib,opa_vnic: Update MAINTAINERS
IB/rdmavt: Fix sizeof mismatch
MAINTAINERS: CISCO VIC LOW LATENCY NIC DRIVER
RDMA/bnxt_re: Fix sizeof mismatch for allocation of pbl_tbl.
RDMA/bnxt_re: Use rdma_umem_for_each_dma_block()
RDMA/umem: Move to allocate SG table from pages
lib/scatterlist: Add support in dynamic allocation of SG table from pages
tools/testing/scatterlist: Show errors in human readable form
tools/testing/scatterlist: Rejuvenate bit-rotten test
RDMA/ipoib: Set rtnl_link_ops for ipoib interfaces
RDMA/uverbs: Expose the new GID query API to user space
...
Add new FTE in TX IPsec FT per IPsec state. It has the
same matching criteria as the RX steering rule.
The IPsec FT is created/destroyed when the first/last rule
is added/deleted respectively.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add new namespace that represents the NIC TX domain.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Firmware live patch event notifies the driver that the firmware was just
updated using live patch. In such case the driver should not reload or
re-initiate entities, part to updating the firmware version and
re-initiate the firmware tracer which can be updated by live patch with
new strings database to help debugging an issue.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Once the driver gets sync_reset_request from firmware it prepares for the
coming reset and sends acknowledge.
After getting this event the driver expects device reset, either it will
trigger PCI reset on sync_reset_now event or such PCI reset will be
triggered by another PF of the same device. So it moves to reset
requested mode and if it gets PCI reset triggered by the other PF it
detect the reset and reloads.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of pci is offline reclaim_pages_cmd() will still try to call
the FW to release FW pages, cmd_exec() in this case will return a silent
success without actually calling the FW.
This is wrong and will cause page leaks, what we should do is to detect
pci offline or command interface un-available before tying to access the
FW and manually release the FW pages in the driver.
In this patch we share the code to check for FW command interface
availability and we call it in sensitive places e.g. reclaim_pages_cmd().
Alternative fix:
1. Remove MLX5_CMD_OP_MANAGE_PAGES form mlx5_internal_err_ret_value,
command success simulation list.
2. Always Release FW pages even if cmd_exec fails in reclaim_pages_cmd().
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Upon command completion timeout, driver simulates a forced command
completion. In a rare case where real interrupt for that command arrives
simultaneously, it might release the command entry while the forced
handler might still access it.
Fix that by adding an entry refcount, to track current amount of allowed
handlers. Command entry to be released only when this refcount is
decremented to zero.
Command refcount is always initialized to one. For callback commands,
command completion handler is the symmetric flow to decrement it. For
non-callback commands, it is wait_func().
Before ringing the doorbell, increment the refcount for the real completion
handler. Once the real completion handler is called, it will decrement it.
For callback commands, once the delayed work is scheduled, increment the
refcount. Upon callback command completion handler, we will try to cancel
the timeout callback. In case of success, we need to decrement the callback
refcount as it will never run.
In addition, gather the entry index free and the entry free into a one
flow for all command types release.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently only 256 vports can be supported as only 8 bits are
reserved for them and 8 bits are reserved for vhca_ids in
metadata reg c0. To support more than 256 vports, replace
vhca_id with a unique shorter 4-bit PF number which covers
upto 16 PF's. Use remaining 12 bits for vports ranging 1-4095.
This will continue to generate unique metadata even if
multiple PCI devices have same switch_id.
Signed-off-by: sunils <sunils@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Leon Romanovsky