Similar to skb_eth_hdr() introduced in commit 96cc4b6958 ("macvlan: do
not assume mac_header is set in macvlan_broadcast()"), let's introduce a
skb_vlan_eth_hdr() helper which can be used in TX-only code paths to get
to the VLAN header based on skb->data rather than based on the
skb_mac_header(skb).
We also consolidate the drivers that dereference skb->data to go through
this helper.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system hang because of dsa_tag_8021q_port_setup()->
stmmac_vlan_rx_add_vid().
I found in stmmac_drv_probe() that cailing pm_runtime_put()
disabled the clock.
First, when the kernel is compiled with CONFIG_PM=y,The stmmac's
resume/suspend is active.
Secondly,stmmac as DSA master,the dsa_tag_8021q_port_setup() function
will callback stmmac_vlan_rx_add_vid when DSA dirver starts. However,
The system is hanged for the stmmac_vlan_rx_add_vid() accesses its
registers after stmmac's clock is closed.
I would suggest adding the pm_runtime_resume_and_get() to the
stmmac_vlan_rx_add_vid().This guarantees that resuming clock output
while in use.
Fixes: b3dcb31277 ("net: stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Yan Wang <rk.code@outlook.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than casting clk_disable_unprepare to an incompatible function
type provide a trivial wrapper with the correct signature for the
use-case.
Reported by clang-16 with W=1:
drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c:276:6: error: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
(void(*)(void *))clk_disable_unprepare,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20230418-dwmac-meson8b-clk-cb-cast-v1-1-e892b670cbbb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Without the IFF_LIVE_ADDR_CHANGE flag being set, the network code
disallows changing the mac address while the interface is UP.
Consequences are, for instance, that the interface can't be used
in a failover bond.
Add the missing flag to net_device priv_flags.
Tested on Intel Elkhart Lake with default settings, as well as with
failover and alb mode bonds.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_dev_probe doesn't propagate feature flags to VLANs. So features
like offloading don't correspond with the general features and it's not
possible to manipulate features via ethtool -K to affect VLANs.
Propagate feature flags to vlan features. Drop TSO feature because
it does not work on VLANs yet.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Link: https://lore.kernel.org/r/20230417192845.590034-1-vinschen@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dwmac supports multiple modess. When working under rmii and rgmii,
you need to set different phy interfaces.
According to the dwmac document, when working in rmii, it needs to be
set to 0x4, and rgmii needs to be set to 0x1.
The phy interface needs to be set in syscon, the format is as follows:
starfive,syscon: <&syscon, offset, shift>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This adds StarFive dwmac driver support on the StarFive JH7110 SoC.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add "snps,dwmac-5.20" compatible string for 5.20 version that can avoid
to define some platform data in the glue layer.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add receive hardware timestamp metadata support via kfunc to XDP Zero Copy
receive packets.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add receive hardware timestamp metadata support via kfunc to XDP receive
packets.
Suggested-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce struct stmmac_xdp_buff as a preparation to support XDP Rx
metadata via kfuncs.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the new programming sequence needed for EMAC3 based platforms such
as the sc8280xp family.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It seems that this variable should be used for all speeds, not just
1000/100.
While at it refactor it slightly to be more readable, including fixing
the typo in the variable name.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver currently sets a MAC TX delay of 2 ns no matter what the
phy-mode is. If the phy-mode indicates the phy is in charge of the
TX delay (rgmii-txid, rgmii-id), don't do it in the MAC.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some platforms have dwmac4 implementations that have a different
address space layout than the default, resulting in the need to define
their own DMA/MTL offsets.
Extend the functions to allow a platform driver to indicate what its
addresses are, overriding the defaults.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Passing stmmac_priv to some of the callbacks allows hwif implementations
to grab some data that platforms can customize. Adjust the callbacks
accordingly in preparation of such a platform customization.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There's a few spots in the hardware interface where a void pointer is
used, but what's passed in and later cast out is always the same type.
Just use the proper type directly.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
DAM is supposed to be DMA. Fix it to improve readability.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The brackets are unnecessary, remove them to match the coding style
used in the kernel.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The usual devm_regulator_get() call already handles "optional"
regulators by returning a valid dummy and printing a warning
that the dummy regulator should be described properly. This
code open coded the same behaviour, but masked any errors that
are not -EPROBE_DEFER and is quite noisy.
This change effectively unmasks and propagates regulators errors
not involving -ENODEV, downgrades the error print to warning level
if no regulator is specified and captures the probe defer message
for /sys/kernel/debug/devices_deferred.
Fixes: 2e12f53663 ("net: stmmac: dwmac-rk: Use standard devicetree property for phy regulator")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clock requesting code is quite repetitive. Fix this by requesting
the clocks via devm_clk_bulk_get_optional. The optional variant has been
used, since this is effectively what the old code did. The exact clocks
required depend on the platform and configuration. As a side effect
this change adds correct -EPROBE_DEFER handling.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 7ad269ea1a ("GMAC: add driver for Rockchip RK3288 SoCs integrated GMAC")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always return struct anarion_gmac * from anarion_config_dt().
In the case where ctl_block was an error pointer it was being
returned directly. Which sparse flags as follows:
.../dwmac-anarion.c:73:24: warning: incorrect type in return expression (different address spaces)
.../dwmac-anarion.c:73:24: expected struct anarion_gmac *
.../dwmac-anarion.c:73:24: got void [noderef] __iomem *[assigned] ctl_block
Avoid this by converting the error pointer to an error.
And then reversing the conversion.
As a side effect, the error can be used for logging purposes,
subjectively, leading to a minor cleanup.
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use __iomem annotation the register base: the ctl_block field of struct
anarion_gmac. I believe this is the normal practice for such variables.
By doing so some casting is avoided.
And sparse no longer reports:
.../dwmac-anarion.c:29:23: warning: incorrect type in argument 1 (different address spaces)
.../dwmac-anarion.c:29:23: expected void const volatile [noderef] __iomem *addr
.../dwmac-anarion.c:29:23: got void *
.../dwmac-anarion.c:34:22: warning: incorrect type in argument 2 (different address spaces)
.../dwmac-anarion.c:34:22: expected void volatile [noderef] __iomem *addr
.../dwmac-anarion.c:34:22: got void *
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This was never used since the commit that added it - e58bb43f5e
("stmmac: initial support to manage pcs modes").
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230406125412.48790-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some DT devices already have phy device configured in the DT/ACPI.
Current implementation scans for a phy unconditionally even though
there is a phy listed in the DT/ACPI and already attached.
We should check the fwnode if there is any phy device listed in
fwnode and decide whether to scan for a phy to attach to.
Fixes: fe2cfbc968 ("net: stmmac: check if MAC needs to attach to a PHY")
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/lkml/20230403212434.296975-1-martin.blumenstingl@googlemail.com/
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Shahab Vahedi <shahab@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Link: https://lore.kernel.org/r/20230406024541.3556305-1-michael.wei.hong.sit@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Queue reset was moved out from __init_dma_rx_desc_rings() and
__init_dma_tx_desc_rings() functions. Thus, the driver fails to transmit
and receive packet after XDP prog setup.
This commit adds the missing queue reset into stmmac_xdp_open() function.
Fixes: f9ec5723c3 ("net: ethernet: stmicro: stmmac: move queue reset to dedicated functions")
Cc: <stable@vger.kernel.org> # 6.0+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/20230404044823.3226144-1-yoong.siang.song@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The patch addresses an issue with the reset logic on the i.MX93 SoC, which
requires configuration of the correct interface speed under RMII mode to
complete the reset. The patch implements a fix_soc_reset function and uses
it specifically for the i.MX93 SoCs.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230403222302.328262-2-shenwei.wang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support for platform-specific reset logic in the
stmmac driver. Some SoCs require a different reset mechanism than
the standard dwmac IP reset. To support these platforms, a new function
pointer 'fix_soc_reset' is added to the plat_stmmacenet_data structure.
The stmmac_reset in hwif.h is modified to call the 'fix_soc_reset'
function if it exists. This enables the driver to use the platform-specific
reset logic when necessary.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230403222302.328262-1-shenwei.wang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, intel_speed_mode_2500() will fix-up xpcs_an_inband
to 1 if the underlying controller has a max speed of 1000Mbps.
The value has been initialized and modified if it is
a fixed-linked setup earlier.
This patch removes the fix-up to allow for fixed-linked setup
support. In stmmac_phy_setup(), ovr_an_inband is set based on
the value of xpcs_an_inband. Which in turn will return an
error in phylink_parse_mode() where MLO_AN_FIXED and
ovr_an_inband are both set.
Fixes: c82386310d ("stmmac: intel: prepare to support 1000BASE-X phy interface setting")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the introduction of the fixed-link support, the MAC driver
no longer attempt to scan for a PHY to attach to. This causes the
non fixed-link setups to stop working.
Using the phylink_expects_phy() to check and determine if the MAC
should expect and attach a PHY.
Fixes: ab21cf9209 ("net: stmmac: make mdio register skips PHY scanning for fixed-link")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Lai Peter Jun Ann <peter.jun.ann.lai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit has introduced the following tests to
dwmac4_add_hw_vlan_rx_fltr(), called from stmmac_vlan_rx_add_vid():
if (hw->promisc) {
netdev_err(dev,
"Adding VLAN in promisc mode not supported\n");
return -EPERM;
}
"VLAN promiscuous" mode is keyed in this driver to IFF_PROMISC, and so,
vlan_vid_add() and vlan_vid_del() calls cannot take place in IFF_PROMISC
mode. I have the following 2 arguments that this restriction is.... hm,
how shall I put it nicely... unproductive :)
First, take the case of a Linux bridge. If the kernel is compiled with
CONFIG_BRIDGE_VLAN_FILTERING=y, then this bridge shall have a VLAN
database. The bridge shall try to call vlan_add_vid() on its bridge
ports for each VLAN in the VLAN table. It will do this irrespectively of
whether that port is *currently* VLAN-aware or not. So it will do this
even when the bridge was created with vlan_filtering 0.
But the Linux bridge, in VLAN-unaware mode, configures its ports in
promiscuous (IFF_PROMISC) mode, so that they accept packets with any
MAC DA (a switch must do this in order to forward those packets which
are not directly targeted to its MAC address).
As a result, the stmmac driver does not work as a bridge port, when the
kernel is compiled with CONFIG_BRIDGE_VLAN_FILTERING=y.
$ ip link add br0 type bridge && ip link set br0 up
$ ip link set eth0 master br0 && ip link set eth0 up
[ 2333.943296] br0: port 1(eth0) entered blocking state
[ 2333.943381] br0: port 1(eth0) entered disabled state
[ 2333.943782] device eth0 entered promiscuous mode
[ 2333.944080] 4033c000.ethernet eth0: Adding VLAN in promisc mode not supported
[ 2333.976509] 4033c000.ethernet eth0: failed to initialize vlan filtering on this port
RTNETLINK answers: Operation not permitted
Secondly, take the case of stmmac as DSA master. Some switch tagging
protocols are based on 802.1Q VLANs (tag_sja1105.c), and as such,
tag_8021q.c uses vlan_vid_add() to work with VLAN-filtering DSA masters.
But also, when a DSA port becomes promiscuous (for example when it joins
a bridge), the DSA framework also makes the DSA master promiscuous.
Moreover, for every VLAN that a DSA switch sends to the CPU, DSA also
programs a VLAN filter on the DSA master, because if the the DSA switch
uses a tail tag, then the hardware frame parser of the DSA master will
see VLAN as VLAN, and might filter them out, for being unknown.
Due to the above 2 reasons, my belief is that the stmmac driver does not
get to choose to not accept vlan_vid_add() calls while IFF_PROMISC is
enabled, because the 2 are completely independent and there are code
paths in the network stack which directly lead to this situation
occurring, without the user's direct input.
In fact, my belief is that "VLAN promiscuous" mode should have never
been keyed on IFF_PROMISC in the first place, but rather, on the
NETIF_F_HW_VLAN_CTAG_FILTER feature flag which can be toggled by the
user through ethtool -k, when present in netdev->hw_features.
In the stmmac driver, NETIF_F_HW_VLAN_CTAG_FILTER is only present in
"features", making this feature "on [fixed]".
I have this belief because I am unaware of any definition of promiscuity
which implies having an effect on anything other than MAC DA (therefore
not VLAN). However, I seem to be rather alone in having this opinion,
looking back at the disagreements from this discussion:
https://lore.kernel.org/netdev/20201110153958.ci5ekor3o2ekg3ky@ipetronik.com/
In any case, to remove the vlan_vid_add() dependency on !IFF_PROMISC,
one would need to remove the check and see what fails. I guess the test
was there because of the way in which dwmac4_vlan_promisc_enable() is
implemented.
For context, the dwmac4 supports Perfect Filtering for a limited number
of VLANs - dwmac4_get_num_vlan(), priv->hw->num_vlan, with a fallback on
Hash Filtering - priv->dma_cap.vlhash - see stmmac_vlan_update(), also
visible in cat /sys/kernel/debug/stmmaceth/eth0/dma_cap | grep 'VLAN
Hash Filtering'.
The perfect filtering is based on MAC_VLAN_Tag_Filter/MAC_VLAN_Tag_Data
registers, accessed in the driver through dwmac4_write_vlan_filter().
The hash filtering is based on the MAC_VLAN_Hash_Table register, named
GMAC_VLAN_HASH_TABLE in the driver and accessed by dwmac4_update_vlan_hash().
The control bit for enabling hash filtering is GMAC_VLAN_VTHM
(MAC_VLAN_Tag_Ctrl bit VTHM: VLAN Tag Hash Table Match Enable).
Now, the description of dwmac4_vlan_promisc_enable() is that it iterates
through the driver's cache of perfect filter entries (hw->vlan_filter[i],
added by dwmac4_add_hw_vlan_rx_fltr()), and evicts them from hardware by
unsetting their GMAC_VLAN_TAG_DATA_VEN (MAC_VLAN_Tag_Data bit VEN - VLAN
Tag Enable) bit. Then it unsets the GMAC_VLAN_VTHM bit, which disables
hash matching.
This leaves the MAC, according to table "VLAN Match Status" from the
documentation, to always enter these data paths:
VID |VLAN Perfect Filter |VTHM Bit |VLAN Hash Filter |Final VLAN Match
|Match Result | |Match Result |Status
-------|--------------------|---------|-----------------|----------------
VID!=0 |Fail |0 |don't care |Pass
So, dwmac4_vlan_promisc_enable() does its job, but by unsetting
GMAC_VLAN_VTHM, it conflicts with the other code path which controls
this bit: dwmac4_update_vlan_hash(), called through stmmac_update_vlan_hash()
from stmmac_vlan_rx_add_vid() and from stmmac_vlan_rx_kill_vid().
This is, I guess, why dwmac4_add_hw_vlan_rx_fltr() is not allowed to run
after dwmac4_vlan_promisc_enable() has unset GMAC_VLAN_VTHM: because if
it did, then dwmac4_update_vlan_hash() would set GMAC_VLAN_VTHM again,
breaking the "VLAN promiscuity".
It turns out that dwmac4_vlan_promisc_enable() is way too complicated
for what needs to be done. The MAC_Packet_Filter register also has the
VTFE bit (VLAN Tag Filter Enable), which simply controls whether VLAN
tagged packets which don't match the filtering tables (either perfect or
hash) are dropped or not. At the moment, this driver unconditionally
sets GMAC_PACKET_FILTER_VTFE if NETIF_F_HW_VLAN_CTAG_FILTER was detected
through the priv->dma_cap.vlhash capability bits of the device, in
stmmac_dvr_probe().
I would suggest deleting the unnecessarily complex logic from
dwmac4_vlan_promisc_enable(), and simply unsetting GMAC_PACKET_FILTER_VTFE
when becoming IFF_PROMISC, which has the same effect of allowing packets
with any VLAN tags, but has the additional benefit of being able to run
concurrently with stmmac_vlan_rx_add_vid() and stmmac_vlan_rx_kill_vid().
As much as I believe that the VTFE bit should have been exclusively
controlled by NETIF_F_HW_VLAN_CTAG_FILTER through ethtool, and not by
IFF_PROMISC, changing that is not a punctual fix to the problem, and it
would probably break the VFFQ feature added by the later commit
e0f9956a38 ("net: stmmac: Add option for VLAN filter fail queue
enable"). From the commit description, VFFQ needs IFF_PROMISC=on and
VTFE=off in order to work (and this change respects that). But if VTFE
was changed to be controlled through ethtool -k, then a user-visible
change would have been introduced in Intel's scripts (a need to run
"ethtool -k eth0 rx-vlan-filter off" which did not exist before).
The patch was tested with this set of commands:
ip link set eth0 up
ip link add link eth0 name eth0.100 type vlan id 100
ip addr add 192.168.100.2/24 dev eth0.100 && ip link set eth0.100 up
ip link set eth0 promisc on
ip link add link eth0 name eth0.101 type vlan id 101
ip addr add 192.168.101.2/24 dev eth0.101 && ip link set eth0.101 up
ip link set eth0 promisc off
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link set eth0 promisc on
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link del eth0.100
ip link del eth0.101
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we should see them
ip link set eth0 promisc off
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we shouldn't see them
# anymore, but remove the "-p" argument from tcpdump and they're there.
Fixes: c89f44ff10 ("net: stmmac: Add support for VLAN promiscuous mode")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DMA address width is either read from a RO device register
or force set from the platform data. This breaks DMA when the host DMA
address width is <=32it but the device is >32bit.
Right now the driver may decide to use a 2nd DMA descriptor for
another buffer (happens in case of TSO xmit) assuming that 32bit
addressing is used due to platform configuration but the device will
still use both descriptor addresses as one address.
This can be observed with the Intel EHL platform driver that sets
32bit for addr64 but the MAC reports 40bit. The TX queue gets stuck in
case of TCP with iptables NAT configuration on TSO packets.
The logic should be like this: Whatever we do on the host side (memory
allocation GFP flags) should happen with the host DMA width, whenever
we decide how to set addresses on the device registers we must use the
device DMA address width.
This patch renames the platform address width field from addr64 (term
used in device datasheet) to host_addr and uses this value exclusively
for host side operations while all chip operations consider the device
DMA width as read from the device register.
Fixes: 7cfc4486e7 ("stmmac: intel: Configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA addressing")
Signed-off-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for net/can
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here).
drivers/net/ethernet/stmicro/stmmac/dwmac-generic.c:72:34: error: ‘dwmac_generic_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is specific to ARCH_QCOM which depends on OF thus the driver
is OF-only. Its of_device_id table is built unconditionally, thus
of_match_ptr() for ID table does not make sense.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When MAC is not support PMT, driver will check PHY's WoL capability
and set device wakeup capability in stmmac_init_phy(). We can enable
the WoL through ethtool, the driver would enable the device wake up
flag. Now the device_may_wakeup() return true.
But if there is a way which enable the PHY's WoL capability derectly,
like in BIOS. The driver would not know the enable thing and would not
set the device wake up flag. The phy_suspend may failed like this:
[ 32.409063] PM: dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x50 returns -16
[ 32.409065] PM: Device stmmac-1:00 failed to suspend: error -16
[ 32.409067] PM: Some devices failed to suspend, or early wake event detected
Add to set the device wakeup enable flag according to the get_wol
function result in PHY can fix the error in this scene.
v2: add a Fixes tag.
Fixes: 1d8e5b0f3f ("net: stmmac: Support WOL with phy")
Signed-off-by: Rongguang Wei <weirongguang@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting 'snps,force_thresh_dma_mode' DT property, the following
warning is always emitted, regardless the status of force_sf_dma_mode:
dwmac-starfive 10020000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
Do not print the rather misleading message when DMA store and forward
mode is already disabled.
Fixes: e2a240c7d3 ("driver:net:stmmac: Disable DMA store and forward mode if platform data force_thresh_dma_mode is set.")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230210202126.877548-1-cristian.ciocaltea@collabora.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
So far changing the period by just setting new period values while
running did not work.
The order as indicated by the publicly available reference manual of the i.MX8MP [1]
indicates a sequence:
* initiate the programming sequence
* set the values for PPS period and start time
* start the pulse train generation.
This is currently not used in dwmac5_flex_pps_config(), which instead does:
* initiate the programming sequence and immediately start the pulse train generation
* set the values for PPS period and start time
This caused the period values written not to take effect until the FlexPPS output was
disabled and re-enabled again.
This patch fix the order and allows the period to be set immediately.
[1] https://www.nxp.com/webapp/Download?colCode=IMX8MPRM
Fixes: 9a8a02c9d4 ("net: stmmac: Add Flexible PPS support")
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230210143937.3427483-1-j.zink@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All implementations of the remove callback return 0 unconditionally. So
in dwc_eth_dwmac_remove() there is no error handling necessary. Simplify
accordingly.
This is a preparation for making struct platform_driver::remove return
void, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230211112431.214252-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function returns zero unconditionally. Change it to return void instead
which simplifies some callers as error handing becomes unnecessary.
This also makes it more obvious that most platform remove callbacks always
return zero.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230211112431.214252-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCY+bZrwAKCRDbK58LschI
gzi4AP4+TYo0jnSwwkrOoN9l4f5VO9X8osmj3CXfHBv7BGWVxAD/WnvA3TDZyaUd
agIZTkRs6BHF9He8oROypARZxTeMLwM=
=nO1C
-----END PGP SIGNATURE-----
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad2 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are 2 classes of in-tree drivers currently:
- those who act upon struct tc_taprio_sched_entry :: gate_mask as if it
holds a bit mask of TXQs
- those who act upon the gate_mask as if it holds a bit mask of TCs
When it comes to the standard, IEEE 802.1Q-2018 does say this in the
second paragraph of section 8.6.8.4 Enhancements for scheduled traffic:
| A gate control list associated with each Port contains an ordered list
| of gate operations. Each gate operation changes the transmission gate
| state for the gate associated with each of the Port's traffic class
| queues and allows associated control operations to be scheduled.
In typically obtuse language, it refers to a "traffic class queue"
rather than a "traffic class" or a "queue". But careful reading of
802.1Q clarifies that "traffic class" and "queue" are in fact
synonymous (see 8.6.6 Queuing frames):
| A queue in this context is not necessarily a single FIFO data structure.
| A queue is a record of all frames of a given traffic class awaiting
| transmission on a given Bridge Port. The structure of this record is not
| specified.
i.o.w. their definition of "queue" isn't the Linux TX queue.
The gate_mask really is input into taprio via its UAPI as a mask of
traffic classes, but taprio_sched_to_offload() converts it into a TXQ
mask.
The breakdown of drivers which handle TC_SETUP_QDISC_TAPRIO is:
- hellcreek, felix, sja1105: these are DSA switches, it's not even very
clear what TXQs correspond to, other than purely software constructs.
Only the mqprio configuration with 8 TCs and 1 TXQ per TC makes sense.
So it's fine to convert these to a gate mask per TC.
- enetc: I have the hardware and can confirm that the gate mask is per
TC, and affects all TXQs (BD rings) configured for that priority.
- igc: in igc_save_qbv_schedule(), the gate_mask is clearly interpreted
to be per-TXQ.
- tsnep: Gerhard Engleder clarifies that even though this hardware
supports at most 1 TXQ per TC, the TXQ indices may be different from
the TC values themselves, and it is the TXQ indices that matter to
this hardware. So keep it per-TXQ as well.
- stmmac: I have a GMAC datasheet, and in the EST section it does
specify that the gate events are per TXQ rather than per TC.
- lan966x: again, this is a switch, and while not a DSA one, the way in
which it implements lan966x_mqprio_add() - by only allowing num_tc ==
NUM_PRIO_QUEUES (8) - makes it clear to me that TXQs are a purely
software construct here as well. They seem to map 1:1 with TCs.
- am65_cpsw: from looking at am65_cpsw_est_set_sched_cmds(), I get the
impression that the fetch_allow variable is treated like a prio_mask.
This definitely sounds closer to a per-TC gate mask rather than a
per-TXQ one, and TI documentation does seem to recomment an identity
mapping between TCs and TXQs. However, Roger Quadros would like to do
some testing before making changes, so I'm leaving this driver to
operate as it did before, for now. Link with more details at the end.
Based on this breakdown, we have 5 drivers with a gate mask per TC and
4 with a gate mask per TXQ. So let's make the gate mask per TXQ the
opt-in and the gate mask per TC the default.
Benefit from the TC_QUERY_CAPS feature that Jakub suggested we add, and
query the device driver before calling the proper ndo_setup_tc(), and
figure out if it expects one or the other format.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20230202003621.2679603-15-vladimir.oltean@nxp.com/#25193204
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Siddharth Vadapalli <s-vadapalli@ti.com>
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean