There is only one GIF flag for the whole processor, so make sure it is not clobbered
when switching to L2 (in which case we also have to include the V_GIF_ENABLE_MASK,
lest we confuse enable_gif/disable_gif/gif_set). When going back, L1 could in
theory have entered L2 without issuing a CLGI so make sure the svm_set_gif is
done last, after svm->vmcb->control.int_ctl has been copied back from hsave.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extract the code that is needed to implement CLGI and STGI,
so that we can run it from VMRUN and vmexit (and in the future,
KVM_SET_NESTED_STATE). Skip the request for KVM_REQ_EVENT unless needed,
subsuming the evaluate_pending_interrupts optimization that is found
in enter_svm_guest_mode.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_vcpu_apicv_active must be false when nested virtualization is enabled,
so there is no need to check it in clgi_interception.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The control state changes on every L2->L0 vmexit, and we will have to
serialize it in the nested state. So keep it up to date in svm->nested.ctl
and just copy them back to the nested VMCB in nested_svm_vmexit.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Restore the INT_CTL value from the guest's VMCB once we've stopped using
it, so that virtual interrupts can be injected as requested by L1.
V_TPR is up-to-date however, and it can change if the guest writes to CR8,
so keep it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In preparation for nested SVM save/restore, store all data that matters
from the VMCB control area into svm->nested. It will then become part
of the nested SVM state that is saved by KVM_SET_NESTED_STATE and
restored by KVM_GET_NESTED_STATE, just like the cached vmcs12 for nVMX.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow placing the VMCB structs on the stack or in other structs without
wasting too much space. Add BUILD_BUG_ON as a quick safeguard against typos.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use l1_tsc_offset to compute svm->vcpu.arch.tsc_offset and
svm->vmcb->control.tsc_offset, instead of relying on hsave.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Split out filling svm->vmcb.save and svm->vmcb.control before VMRUN.
Only the latter will be useful when restoring nested SVM state.
This patch introduces no semantic change, so the MMU setup is still
done in nested_prepare_vmcb_save. The next patch will clean up things.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When restoring SVM nested state, the control state cache in svm->nested
will have to be filled, but the save state will not have to be moved
into svm->vmcb. Therefore, pull the code that handles the control area
into a separate function.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unmapping the nested VMCB in enter_svm_guest_mode is a bit of a wart,
since the map argument is not used elsewhere in the function. There are
just two callers, and those are also the place where kvm_vcpu_map is
called, so it is cleaner to unmap there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The userspace_addr alignment and range checks are not performed for private
memory slots that are prepared by KVM itself. This is unnecessary and makes
it questionable to use __*_user functions to access memory later on. We also
rely on the userspace address being aligned since we have an entire family
of functions to map gfn to pfn.
Fortunately skipping the check is completely unnecessary. Only x86 uses
private memslots and their userspace_addr is obtained from vm_mmap,
therefore it must be below PAGE_OFFSET. In fact, any attempt to pass
an address above PAGE_OFFSET would have failed because such an address
would return true for kvm_is_error_hva.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This commit:
818e915fbac5: ("irqchip: Add Loongson HyperTransport Vector support")
Added a MIPS-only driver, but turned on compilation on all other architectures as well:
config LOONGSON_HTVEC
bool "Loongson3 HyperTransport Interrupt Vector Controller"
depends on MACH_LOONGSON64 || COMPILE_TEST
But this driver was never build tested on any other architecture than MIPS:
drivers/irqchip/irq-loongson-htvec.c: In function ‘htvec_irq_dispatch’:
drivers/irqchip/irq-loongson-htvec.c:59:3: error: implicit declaration of function ‘spurious_interrupt’; did you mean ‘smp_reboot_interrupt’? [-Werror=implicit-function-declaration]
Because spurious_interrupt() only exists on MIPS.
So make it MIPS-only.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The DT node of the device may contain interconnect paths while the OPP
table doesn't have the bandwidth values. There is no need to parse the
paths in such cases.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
[ Viresh: Support the case of !opp_table and massaged changelog ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The audio driver can call into nouveau right while we're in the middle
of re-fetching the EDID, and decide it no longer needs to be awake.
Stop depending on EDID in the audio component get_eld() callback, and
instead cache whether audio support is present from the prior modeset.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is a SOR register, and not indexed by the bound head.
Fixes display not coming up on high-bandwidth HDMI displays under a
number of configurations.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
QCA6390 memdump VSE sometimes come to bluetooth driver
with wrong sequence number as illustrated as follows:
frame # in dec: frame data in hex
1396: ff fd 01 08 74 05 00 37 8f 14
1397: ff fd 01 08 75 05 00 ff bf 38
1414: ff fd 01 08 86 05 00 fb 5e 4b
1399: ff fd 01 08 77 05 00 f3 44 0a
1400: ff fd 01 08 78 05 00 ca f7 41
it is mistook for controller missing packets, so results
in page fault after overwriting memdump buffer allocated.
Fixed by ignoring QCA6390 sequence number check and
checking buffer space before writing.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Tested-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Convert the sdhci-pxa binding to DT schema format using json-schema.
At the same time, fix a couple of issues with the examples discovered by
the validation tool -- a semicolon instead of a comma and wrong node names.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20200521091356.2211020-2-lkundrak@v3.sk
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
serdev_device_write() is not appropriate at here because
serdev_device_write_wakeup() is not used to release completion hold
by the former at @write_wakeup member of struct serdev_device_ops.
Fix by using serdev_device_write_buf() instead of serdev_device_write().
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Clear tuning_done flag while executing tuning to ensure vendor
specific HS400 settings are applied properly when the controller
is re-initialized in HS400 mode.
Without this, re-initialization of the qcom SDHC in HS400 mode fails
while resuming the driver from runtime-suspend or system-suspend.
Fixes: ff06ce4178 ("mmc: sdhci-msm: Add HS400 platform support")
Cc: stable@vger.kernel.org
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1590678838-18099-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Controller ID info got by VSC EDL_PATCH_GETVER is very
important, so improve its log level from DEBUG to INFO.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Joe Perches pointed out that we were missing a newline
at the end of two debug messages
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Use pr_fmt to standardize all logging for fs/cifs.
Some logging output had no CIFS: specific prefix.
Now all output has one of three prefixes:
o CIFS:
o CIFS: VFS:
o Root-CIFS:
Miscellanea:
o Convert printks to pr_<level>
o Neaten macro definitions
o Remove embedded CIFS: prefixes from formats
o Convert "illegal" to "invalid"
o Coalesce formats
o Add missing '\n' format terminations
o Consolidate multiple cifs_dbg continuations into single calls
o More consistent use of upper case first word output logging
o Multiline statement argument alignment and wrapping
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
In order to handle workloads where it is important to make sure that
a buggy app did not delete content on the drive, the new mount option
"nodelete" allows standard permission checks on the server to work,
but prevents on the client any attempts to unlink a file or delete
a directory on that mount point. This can be helpful when running
a little understood app on a network mount that contains important
content that should not be deleted.
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Move some large data structures off the stack and into dynamically
allocated memory in the function smb2_ioctl_query_info
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Move a lot of structures and arrays off the stack and into a dynamically
allocated structure instead.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The target iterator parameter "it" is not used in
reconn_setup_dfs_targets(), so just remove it.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
In order to support reconnect to hostnames that resolve to same ip
address, besides relying on the currently set hostname to match DFS
targets, attempt to resolve the targets and then match their addresses
with the reconnected server ip address.
For instance, if we have two hostnames "FOO" and "BAR", and both
resolve to the same ip address, we would be able to handle failover in
DFS paths like
\\FOO\dfs\link1 -> [ \BAZ\share2 (*), \BAR\share1 ]
\\FOO\dfs\link2 -> [ \BAZ\share2 (*), \FOO\share1 ]
so when "BAZ" is no longer accessible, link1 and link2 would get
reconnected despite having different target hostnames.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
If we mount a very specific DFS link
\\FS0.FOO.COM\dfs\link -> \FS0\share1, \FS1\share2
where its target list contains NB names ("FS0" & "FS1") rather than
FQDN ones ("FS0.FOO.COM" & "FS1.FOO.COM"), we end up connecting to
\FOO\share1 but server->hostname will have "FOO.COM". The reason is
because both "FS0" and "FS0.FOO.COM" resolve to same IP address and
they share same TCP server connection, but "FS0.FOO.COM" was the first
hostname set -- which is OK.
However, if the echo thread timeouts and we still have a good
connection to "FS0", in cifs_reconnect()
rc = generic_ip_connect(server) -> success
if (rc) {
...
reconn_inval_dfs_target(server, cifs_sb, &tgt_list,
&tgt_it);
...
}
...
it successfully reconnects to "FS0" server but does not set up next
DFS target - which should be the same target server "\FS0\share1" -
and server->hostname remains set to "FS0.FOO.COM" rather than "FS0",
as reconn_inval_dfs_target() would have it set to "FS0" if called
earlier.
Finally, in __smb2_reconnect(), the reconnect of tcons would fail
because tcon->ses->server->hostname (FS0.FOO.COM) does not match DFS
target's hostname (FS0).
Fix that by calling reconn_inval_dfs_target() before
generic_ip_connect() so server->hostname will get updated correctly
prior to reconnecting its tcons in __smb2_reconnect().
With "cifs: handle hostnames that resolve to same ip in failover"
patch
- The above problem would not occur.
- We could save an DNS query to find out that they both resolve to
the same ip address.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The variable rc is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The "nolease" mount option is only supported for SMB2+ mounts.
Fail with appropriate error message if vers=1.0 option is passed.
Signed-off-by: Kenneth D'souza <kdsouza@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
This introduces mtdpstore, which is similar to mtdoops but more
powerful. It uses pstore/blk, and aims to store panic and oops logs to
a flash partition, where pstore can later read back and present as files
in the mounted pstore filesystem.
To make mtdpstore work, the "blkdev" of pstore/blk should be set
as MTD device name or MTD device number. For more details, see
Documentation/admin-guide/pstore-blk.rst
This solves a number of issues:
- Work duplication: both of pstore and mtdoops do the same job storing
panic/oops log. They have very similar logic, registering to kmsg
dumper and storing logs to several chunks one by one.
- Layer violations: drivers should provides methods instead of polices.
MTD should provide read/write/erase operations, and allow a higher
level drivers to provide the chunk management, kmsg dump
configuration, etc.
- Missing features: pstore provides many additional features, including
presenting the logs as files, logging dump time and count, and
supporting other frontends like pmsg, console, etc.
Signed-off-by: WeiXiong Liao <liaoweixiong@allwinnertech.com>
Link: https://lore.kernel.org/lkml/20200511233229.27745-11-keescook@chromium.org/
Link: https://lore.kernel.org/r/1589266715-4168-1-git-send-email-liaoweixiong@allwinnertech.com
Signed-off-by: Kees Cook <keescook@chromium.org>
In order to use arbitrary block devices as a pstore backend, provide a
new module param named "best_effort", which will allow using any block
device, even if it has not provided a panic_write callback.
Link: https://lore.kernel.org/lkml/20200511233229.27745-12-keescook@chromium.org/
Signed-off-by: Kees Cook <keescook@chromium.org>
Add support for non-block devices (e.g. MTD). A non-block driver calls
pstore_blk_register_device() to register iself.
In addition, pstore/zone is updated to handle non-block devices,
where an erase must be done before a write. Without this, there is no
way to remove records stored to an MTD.
Signed-off-by: WeiXiong Liao <liaoweixiong@allwinnertech.com>
Link: https://lore.kernel.org/lkml/20200511233229.27745-10-keescook@chromium.org/
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
In order to configure itself, the MTD backend needs to be able to query
the current pstore configuration. Introduce pstore_blk_get_config() for
this purpose.
Signed-off-by: WeiXiong Liao <liaoweixiong@allwinnertech.com>
Link: https://lore.kernel.org/lkml/20200511233229.27745-9-keescook@chromium.org/
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
One requirement to support MTD devices in pstore/zone is having a
way to declare certain regions as broken. Add this support to
pstore/zone.
The MTD driver should return -ENOMSG when encountering a bad region,
which tells pstore/zone to skip and try the next one.
Signed-off-by: WeiXiong Liao <liaoweixiong@allwinnertech.com>
Link: https://lore.kernel.org/lkml/20200511233229.27745-8-keescook@chromium.org/
Co-developed-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: //lore.kernel.org/lkml/20200512173801.222666-1-colin.king@canonical.com
Signed-off-by: Kees Cook <keescook@chromium.org>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAl7TfecACgkQB8qZga/f
l8Tx6hAAgRizfdHb9xxp001AAzKnsdU46srOKOhwV2d6w+S+qHbLtwa0Xz43pBvX
LxpQs7dBQBLYh11xJhDlKY6duYV989xGcsHm7suO43jbjDo8KXfz4MaP65em6EKt
pdD0mD1sKkfR4FhYNbUEe8Ug/185jdk+gX+aI1Nrz6XlkUoiY+czSnGFyAvpvau2
I+NGqyKG5D6ureq7p7dQcgN+t2D4Ou9stVhpQ+jP0Ep720gvfTEzeFuMJbb3JZ1y
KSgOOWS1HQj1FdlJDs3KAmgUXpkU/lxZhNxl06MMYo3tB7Y0vmLoy/ZNcb5eW4Sw
a0SHgG5yhDysCyINz6q7llG3esDcppGiNuMjd/qR2qPOZPHNtlYaHtcoKBcKdS0k
03DyURZpA0B33cr9FTV8tXaM7IMY/2qaq/DqkeNtuDzGdh4jEwkVJ4fNtUAdgcOv
4JEz3A7fY3isy8tzi7Dom4U/2hR1di5gZloAC5PPYRvnbmY9HoIqG06k1Wtn1Yj4
pbquqvdJ5ONcaAaXz7zVQUZm1JzrK81Pl3pdih7USasc8z2MEzWQPSR+hxtwG5TY
KbDI1Nel8ZLbL2MWDakh3+lPoJAMuyadRlVVWEMj4l/afYHgcy5hEbaMbaZnxmAg
G4I6R5JZTJZuVdKi/U/Q9n7jR83qfIRNbxMLY8HFZ4caJ5qhZGs=
=wdaG
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes, including
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Working on the OpenRISC glibc port I found that sometimes clone was
working strange. That the tls data argument sent in r7 was always
wrong. Further investigation revealed that the arguments were getting
clobbered in the entry code. This patch removes the code that writes to
the argument registers. This was likely due to some old code hanging
around.
This patch fixes this up for clone and fork. This fork clobber is
harmless but also useless so remove.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Recomputing the uids, gids, capabilities, and related flags each time a
new bprm->file is set is error prone and unnecessary.
This set of changes splits per_clear temporarily into two separate
variables. This is the last change necessary to ensure that
everything that is computed from brpm->file in bprm->cred is
recomputed every time a new bprm->file is set. Then the code is
refactored to compute bprm->cred from bprm->file when the final
brpm->file is known, removing the need for recomputation entirely.
Doing this in two steps should allow anyone who has problems later to
bisect and tell if it was the semantic change or the refactoring that
caused them problems.
Eric W. Biederman (2):
exec: Add a per bprm->file version of per_clear
exec: Compute file based creds only once
fs/binfmt_misc.c | 2 +-
fs/exec.c | 57 ++++++++++++++++++-------------------------
include/linux/binfmts.h | 9 ++-----
include/linux/lsm_hook_defs.h | 2 +-
include/linux/lsm_hooks.h | 22 +++++++++--------
include/linux/security.h | 9 ++++---
security/commoncap.c | 22 +++++++++--------
security/security.c | 4 +--
8 files changed, 59 insertions(+), 68 deletions(-)
Merge branch 'exec-norecompute-v2' into exec-next
Yes, staying withing 80 columns is certainly still _preferred_. But
it's not the hard limit that the checkpatch warnings imply, and other
concerns can most certainly dominate.
Increase the default limit to 100 characters. Not because 100
characters is some hard limit either, but that's certainly a "what are
you doing" kind of value and less likely to be about the occasional
slightly longer lines.
Miscellanea:
- to avoid unnecessary whitespace changes in files, checkpatch will no
longer emit a warning about line length when scanning files unless
--strict is also used
- Add a bit to coding-style about alignment to open parenthesis
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paolo Bonzini