Prevent race where we're removing the module and we get link update
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Problem Statement:
- Driver has fc_id of 0xcc0200
- Driver gets link down (due to test) and calls fcoe_ctlr_link_down().
- At this point, the fc_id of the initiator port is zeroed out.
- Driver gets a link up 14 seconds later.
- Driver performs FIP VLAN request, gets a response from the switch.
- No change in VLAN is detected.
- Driver then notifies libfcoe via fcoe_ctlr_link_up().
- Libfcoe then issues a multicast discovery solicitation as expected.
- Cisco FCF responds to that correctly.
- Libfcoe at this point starts a 3 sec count-down to allow any other FCFs
to be discovered. However, at this point, it has been 20 seconds since
the last FKA from the driver (which would have been sent prior to
backlink toggle), which causes the CVL to be issued from Cisco CVL from
the switch is dropped by the driver as the vx_port identification
descriptor is present and has value of 0xcc0200, which does not match
the driver's value of 0. Libfcoe completes the 3 sec count down and
proceeds to issue FLOGI as per protocol. Switch rejects FLogi request.
All subsequent FLOGI requests from libfc are rejected by the switch
(possibly because it is now expecting a new solicitation). This
situation will continue until the next link toggle.
Solution:
The Vx_port descriptor in the CVL has three fields:
MAC address
Fabric ID
Port Name
Today, the code checks for both #1 and #2 above. In the case where we went
through a link down, both these will be zero until FLOGI succeeds.
We should change our code to check if any one of these 3 is valid and if
so, handle the CVL (basically switching from AND to OR). The port name
field is definitely expected to be valid always.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Log s_id, d_id, type and command to the log message.
[mkp: fixed warning]
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current code doeesn't support 20Gbps speed for current and supported
speed. Add support for it.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was wrongly interpreting the supported cap value returned by qed.
Solution: Use QED define macros instead of OS defined for interpreting
supporting speeds.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was attempting to print cdb[0], which is not set for resets coming
from SCSI ioctls. Check for cmd_len before accessing cmnd.
Crash info:
[84790.864747] BUG: unable to handle kernel NULL pointer dereference at (null)
[84790.864783] IP: qedf_initiate_tmf+0x7a/0x6e0 [qedf]
[84790.865204] Call Trace:
[84790.865246] scsi_try_target_reset+0x2b/0x90 [scsi_mod]
[84790.865266] scsi_ioctl_reset+0x20f/0x2a0 [scsi_mod]
[84790.865284] scsi_ioctl+0x131/0x3a0 [scsi_mod]
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- On some setups fipvlan can be retried for long duration and the
connection to switch was not there so it was not getting any reply.
- During unload this thread was hanging.
Problem Resolution:
Check if unload is in progress, then quit from fipvlan thread.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print messages during exiting condition to help debugging.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add:
PM8222 VID_9005, DID_028F, SVID_1BD4 and SDID_004F
3101E-4i (1G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0808
3102E-8i (2G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0809
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return -EINPROGRESS when a rescan worker is queued.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When each ld is deleted, a rescan event is triggered in the driver. These
can stack up waiting on mutex_lock.
Change to mutex_try_lock and schedule a rescan for later.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return identify physical device "Phys_Bay_in_Box" as bay_identifier.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- serial number
- model
- vendor
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Expose physical devices before logical devices.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 12.4.0.0 patch that merged WQ/CQ pairs into single per-cpu pair
contained a bug: a local variable was set to the queue pair by index. This
should have allowed the local variable to be natively used. Instead, the
code reused the index relative to the local variable, obtaining a random
pointer value that when used eventually faulted the system
Convert offending code to use local variable.
Fixes: c00f62e6c5 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Raise the config max for lpfc_fcp_mq_threshold variable to 256.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Capturing and downloading dif command data and dif data was done a dozen
years ago and no longer being used. Also creates a potential security hole.
Remove the debugfs buffer for dif debugging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: KyleMahlkuch <kmahlkuc@linux.vnet.ibm.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Per Dan Carpenter:
The patch d79c9e9d4b3d: "scsi: lpfc: Support dynamic unbounded SGL lists on
G7 hardware." from Aug 14, 2019, leads to the following static checker
warning:
drivers/scsi/lpfc/lpfc_init.c:4107 lpfc_new_io_buf()
error: not allocating enough data 784 vs 768
There was no need to compare sizes nor to allocate size based on a define.
Change allocation to use actual structure length
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/ufs/ufs-qcom.c: In function ufs_qcom_pwr_change_notify:
drivers/scsi/ufs/ufs-qcom.c:808:6: warning: variable val set but not used [-Wunused-but-set-variable]
Fixes: 1e1e465c6d ("scsi/ufs: qcom: Remove ufs_qcom_phy_*() calls from host")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a spelling mistake in a ql_log message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c: In function cq_interrupt_v1_hw:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:1542:6: warning: variable irq_value set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides a module parameter and sysfs interface to select
whether the queue depth for each device should be based on the
protocol-specific value set by the driver (the default) or the maximum
supported by the controller (can_queue).
Although we have a sysfs interface per sdev to change the queue depth
of individual scsi devices, this implementation provides a single
sysfs entry per shost to switch between the controller max and the
driver default.
[mkp: tweaked commit desc]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the firmware documentation a status type 0 IOCB can be
followed by one or more status continuation type 0 IOCBs. Hence do not
complain if the completion function is not called from inside the status
type 0 IOCB handler.
WARNING: CPU: 10 PID: 425 at drivers/scsi/qla2xxx/qla_isr.c:2784
qla2x00_status_entry.isra.7+0x484/0x17b0 [qla2xxx]
CPU: 10 PID: 425 Comm: kworker/10:1 Tainted: G E 5.3.0-rc4-next-20190813-autotest-autotest #1
Workqueue: qla2xxx_wq qla25xx_free_rsp_que [qla2xxx]
Call Trace:
qla2x00_status_entry.isra.7+0x1484/0x17b0 [qla2xxx] (unreliable)
qla24xx_process_response_queue+0x7d8/0xbd0 [qla2xxx]
qla25xx_free_rsp_que+0x1a0/0x220 [qla2xxx]
process_one_work+0x25c/0x520
worker_thread+0x8c/0x5e0
kthread+0x154/0x1a0
ret_from_kernel_thread+0x5c/0x7c
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently bits in hba->outstanding_tasks are cleared only after their
corresponding task management commands are successfully done by
__ufshcd_issue_tm_cmd().
If timeout happens in a task management command, its corresponding bit in
hba->outstanding_tasks will not be cleared until next task management
command with the same tag used successfully finishes.
This is wrong and can lead to some issues, like power issue. For example,
ufshcd_release() and ufshcd_gate_work() will do nothing if
hba->outstanding_tasks is not zero even if both UFS host and devices are
actually idle.
Solution is referred from error handling of device commands: bits in
hba->outstanding_tasks shall be cleared regardless of their execution
results.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pointer fh is being assigned a return value from the call to
skb_transport_header however this value is never read and fh is being
re-assigned immediately afterwards with a new value. Since there are
side-effects from calling skb_transport_header the call is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices have issues if LCC is enabled. So we are setting
PA_LOCAL_TX_LCC_Enable to 0 before link startup which will make sure that
both host and device TX LCC are disabled once link startup is completed.
Signed-off-by: Anil Varughese <aniljoy@cadence.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We don't know when the device will be added with device_add() in
serio_add_port() because serio_add_port() is called from a workqueue
that this driver schedules by calling serio_register_port(). The best we
can know is that the device will definitely not have been added yet when
the start callback is called on the serio device.
While it hasn't been shown to be a problem, proactively move the wakeup
enabling calls to the start hook so that we don't race with the
workqueue calling device_add(). This will avoid racy situations where
code tries to add wakeup sysfs attributes for this device from
dpm_sysfs_add() but the path in device_set_wakeup_capable() has already
done so.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Variable error is being initialized with a value that is never read and
error is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable DC support for renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hook up the DML changes for renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to check for renoir first.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a kconfig option to enable renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable the building of dcn21 support.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add missing parameters, to make dcn21 compile
without errors
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the rev id for renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
call update_bw_bounding_box in DC construct
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hook up renoir support to KMS.
v2: squash in "Fixes for Renoir in amdgpu_dm"
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add Renoir DCN version in DC and handle it
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
rename VM_CONTEXT0 to MMVM_CONTEXT0 as that is the name defined in
the register files
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DML provides the display configuration validation as provided
by the hw teams.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Controls display clocks and interfaces with powerplay for
clock and power requirements.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Saurav Kashyap