The code dealing with busy detection is somewhat complicated. In a way to
make it a bit clearer, let's try to clarify the comments in the code about
it.
Additionally, move the part for clearing the so called busy start IRQ, to
the place where the IRQ is actually delivered. Ideally, this should make
the code a bit more robust.
Finally, to improve understanding of the code and the sequence of the busy
detection, move the corresponding code around a bit in mmci_cmd_irq().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jean Nicolas GRAUX <jean-nicolas.graux@st.com>
Reviewed-by: Jean Nicolas GRAUX <jean-nicolas.graux@st.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The additional emmc2 interface of the BCM2711 is an improved version
of the old emmc controller, which is able to provide DDR50 mode on the
Raspberry Pi 4. Except 32 bit only register access no other quirks are
known yet.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new compatible for the additional emmc2 controller
on BCM2711 and clearify usage.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The conversion to the YAML binding left out two compatibles. Add them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC compatibles in the bindings are not ordered as they should, so
let's make sure it's sorted.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The usdhi6rol0 driver is exclusively used for the ARTPEC family of
SoCs. Other SoCs with the same IP of Panasonic origin use the tmio_mmc
driver. Therefore we assigner maintainer responsibility to us at Axis
until the two drivers become unified.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 414126f9e5.
This commit broke eMMC storage access on a new consumer MiniPC based on
AMD SoC, which has eMMC connected to:
02:00.0 SD Host controller: O2 Micro, Inc. Device 8620 (rev 01) (prog-if 01)
Subsystem: O2 Micro, Inc. Device 0002
During probe, several errors are seen including:
mmc1: Got data interrupt 0x02000000 even though no data operation was in progress.
mmc1: Timeout waiting for hardware interrupt.
mmc1: error -110 whilst initialising MMC card
Reverting this commit allows the eMMC storage to be detected & usable
again.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Fixes: 414126f9e5 ("mmc: sdhci: Remove unneeded quirk2 flag of O2 SD host
controller")
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 37fefadee8 ("mmc: bcm2835: Terminate timeout work
synchronously") causes lockups in case of hardware timeouts due the
timeout work also calling cancel_delayed_work_sync() on its own.
So revert it.
Fixes: 37fefadee8 ("mmc: bcm2835: Terminate timeout work synchronously")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
-----BEGIN PGP SIGNATURE-----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=HAuT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes, but things are settling down:
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190906131032.22148-1-yuehaibing@huawei.com
Acked-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change all exported symbols for managed GPIO functions from
EXPORT_SYMBOL() to EXPORT_SYMBOL_GPL(), like is used for their
non-managed counterparts.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190906084539.21838-5-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 9a95e8d25a ("gpio: remove etraxfs driver"), there are
no more users of of_gpio_simple_xlate() outside gpiolib-of.c.
All GPIO drivers that need it now rely on of_gpiochip_add() setting it
up as the default translate function.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190906084539.21838-3-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit f626d6dfb7 ("gpio: of: Break out OF-only code"),
there are no more users of of_get_named_gpiod_flags() outside
gpiolib-of.c.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190906084539.21838-2-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Receiving an unexpected exit reason from hardware should be considered
as a severe bug in KVM. Therefore, instead of just injecting #UD to
guest and ignore it, exit to userspace on internal error so that
it could handle it properly (probably by terminating guest).
In addition, prefer to use vcpu_unimpl() instead of WARN_ONCE()
as handling unexpected exit reason should be a rare unexpected
event (that was expected to never happen) and we prefer to print
a message on it every time it occurs to guest.
Furthermore, dump VMCS/VMCB to dmesg to assist diagnosing such cases.
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Get rid of the callback, deal with that and dentry in callers
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Configfs abuses symlink(2). Unlike the normal filesystems, it
wants the target resolved at symlink(2) time, like link(2) would've
done. The problem is that ->symlink() is called with the parent
directory locked exclusive, so resolving the target inside the
->symlink() is easily deadlocked.
Short of really ugly games in sys_symlink() itself, all we can
do is to unlock the parent before resolving the target and
relock it after. However, that invalidates the checks done
by the caller of ->symlink(), so we have to
* check that dentry is still where it used to be
(it couldn't have been moved, but it could've been unhashed)
* recheck that it's still negative (somebody else
might've successfully created a symlink with the same name
while we were looking the target up)
* recheck the permissions on the parent directory.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that the Xen special cases are gone nothing worth mentioning is
left in the arm64 <asm/dma-mapping.h> file, so switch to use the
asm-generic version instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Now that we know we always have the dma-noncoherent.h helpers available
if we are on an architecture with support for non-coherent devices,
we can just call them directly, and remove the calls to the dma-direct
routines, including the fact that we call the dma_direct_map_page
routines but ignore the value returned from it. Instead we now have
Xen wrappers for the arch_sync_dma_for_{device,cpu} helpers that call
the special Xen versions of those routines for foreign pages.
Note that the new helpers get the physical address passed in addition
to the dma address to avoid another translation for the local cache
maintainance. The pfn_valid checks remain on the dma address as in
the old code, even if that looks a little funny.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
xen_dma_map_page uses a different and more complicated check for foreign
pages than the other three cache maintainance helpers. Switch it to the
simpler pfn_valid method a well, and document the scheme with a single
improved comment in xen_dma_map_page.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
There is no need to wrap the common version, just wire them up directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
These routines are only used by swiotlb-xen, which cannot be modular.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
arm and arm64 can just use xen_swiotlb_dma_ops directly like x86, no
need for a pointer indirection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Calculate the required operation in the caller, and pass it directly
instead of recalculating it for each page, and use simple arithmetics
to get from the physical address to Xen page size aligned chunks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Use the dma-noncoherent dev_is_dma_coherent helper instead of the home
grown variant. Note that both are always initialized to the same
value in arch_setup_dma_ops.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Shared the duplicate arm/arm64 code in include/xen/arm/page-coherent.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Copy the arm64 code that uses the dma-direct/swiotlb helpers for DMA
on-coherent devices.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Despite the widespread and complete failure of Broadwell integrated
graphics when DMAR is enabled, known over the years, we have never been
able to root cause the issue. Instead, we let the failure undermine our
confidence in the iommu system itself when we should be pushing for it to
be always enabled. Quirk away Broadwell and remove the rotten apple.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89360
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Martin Peres <martin.peres@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Intel VT-d specification revision 3 added support for Scalable Mode
Translation for DMA remapping. Add the Scalable Mode fault reasons to
show detailed fault reasons when the translation fault happens.
Link: https://software.intel.com/sites/default/files/managed/c5/15/vt-directed-io-spec.pdf
Reviewed-by: Sohil Mehta <sohil.mehta@intel.com>
Signed-off-by: Kyung Min Park <kyung.min.park@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The Intel VT-d hardware uses paging for DMA remapping.
The minimum mapped window is a page size. The device
drivers may map buffers not filling the whole IOMMU
window. This allows the device to access to possibly
unrelated memory and a malicious device could exploit
this to perform DMA attacks. To address this, the
Intel IOMMU driver will use bounce pages for those
buffers which don't fill whole IOMMU pages.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Xu Pengfei <pengfei.xu@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This adds trace support for the Intel IOMMU driver. It
also declares some events which could be used to trace
the events when an IOVA is being mapped or unmapped in
a domain.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The bounce page implementation depends on swiotlb. Hence, don't
switch off swiotlb if the system has untrusted devices or could
potentially be hot-added with any untrusted devices.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This adds a helper to check whether a device needs to
use bounce buffer. It also provides a boot time option
to disable the bounce buffer. Users can use this to
prevent the iommu driver from using the bounce buffer
for performance gain.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Xu Pengfei <pengfei.xu@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This splits the size parameter to swiotlb_tbl_map_single() and
swiotlb_tbl_unmap_single() into an alloc_size and a mapping_size
parameter, where the latter one is rounded up to the iommu page
size.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
regulator_uV_show() is missing error handling if regulator_get_voltage_rdev()
returns negative values. Instead it prints the errno as a string, e.g. -EINVAL
as "-22" which could be interpreted as -22 µV.
We also do not need to hold the lock while converting the integer to a string.
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/f37f2a1276efcb34cf3b7f1a25481175be048806.1568143348.git.hns@goldelico.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes 11da04af0d, as devm_gpiod_get_from_of_node() does
not do translation "con-id" -> "con-id-gpios" that our bindings expects,
and therefore it was wrong to change connection ID to be simply "enable"
when moving to using devm_gpiod_get_from_of_node().
Fixes: 11da04af0d ("regulator: da9211: Pass descriptors instead of GPIO numbers")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190910170246.GA56792@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes 96392c3d8c, as devm_gpiod_get_from_of_node() does
not do translation "con-id" -> "con-id-gpios" that our bindings expects,
and therefore it was wrong to change connection ID to be simply
"maxim,ena" when moving to using devm_gpiod_get_from_of_node().
Fixes: 96392c3d8c ("regulator: max77686: Pass descriptor instead of GPIO number")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190910170050.GA55530@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
All these functions declares and initializes variable ret with
'0' and without modifying 'ret' variable, it is returned.
This patch removes this redundancy and returns '0' directly.
Signed-off-by: Saiyam Doshi <saiyamdoshi.in@gmail.com>
Link: https://lore.kernel.org/r/20190909174541.GA22718@SD
Signed-off-by: Mark Brown <broonie@kernel.org>
The ast2600 is a new generation of SoC from ASPEED. Similarly to the
ast2400 and ast2500, it has a GPIO controller for it's 3.3V GPIO pins.
Additionally, it has a GPIO controller for 1.8V GPIO pins.
As the register names for both controllers are the same and the 36 1.8V
GPIOs and the first 36 of the 3.3V GPIOs are all bidirectional, we can
use the same configuration struct and use the ngpio property to
differentiate between the two sets of GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906063737.15428-1-rashmica.g@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the ngpio property from the device tree if it exists. If it doesn't
then fallback to the hardcoded value in the config.
This is in preparation for adding ast2600 support. The ast2600 SoC has
two GPIO controllers and so requires two instances of the GPIO driver.
We use the ngpio property to different between them as they have
different numbers of GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062727.13521-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is in preparation for adding ast2600 support. The ast2600 SoC
requires two instances of the GPIO driver as it has two GPIO
controllers. Each instance needs it's own irqchip.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062644.13445-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current calculation for the number of GPIO banks is only correct if
the number of GPIOs is a multiple of 32 (if there were 31 GPIOs we would
currently say there are 0 banks, which is incorrect).
Fixes: 361b79119a ('gpio: Add Aspeed driver')
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190906062623.13354-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.d.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ast2600 is a new generation of SoC from ASPEED. Similarly to the
ast2400 and ast2500, it has a GPIO controller for it's 3.3V GPIO pins.
Additionally, it has a GPIO controller for 36 1.8V GPIO pins. We use
the ngpio property to differentiate between these controllers.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062547.13264-1-rashmica.g@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ulf Hansson