When bt_en is pulled high by hardware, the host does not re-download
the firmware after SSR. The controller loads the rampatch and NVM
internally.
On HMT chip, the rampatch is ~264 KB and the NVM is ~9.4 KB. The
loading process takes approximately 70 ms. The previous 50 ms delay is
too short, causing the controller to not respond to the reset command
sent by the host, which leads to BT initialization failure:
Bluetooth: hci0: QCA memdump Done, received 458752, total 458752
Bluetooth: hci0: mem_dump_status: 2
Bluetooth: hci0: Opcode 0x0c03 failed: -110
Increase the delay to 100 ms, which was confirmed as a safe value by
the controller, to ensure the controller has finished loading the
firmware before the host sends commands.
Steps to reproduce:
1. Trigger SSR and wait for SSR to complete:
hcitool cmd 0x3f 0c 26
2. Run "bluetoothctl power on" and observe that BT fails to start.
Fixes: fce1a9244a ("Bluetooth: hci_qca: Fix SSR (SubSystem Restart) fail when BT_EN is pulled up by hw")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since the timer uses jiffies as its unit rather than ms, the timeout value
must be converted from ms to jiffies when configuring the timer. Otherwise,
the intended 8s timeout is incorrectly set to approximately 33s.
To improve readability, embed msecs_to_jiffies() directly in the macro
definitions and drop the _MS suffix from macros that now yield jiffies
values: MEMDUMP_TIMEOUT, FW_DOWNLOAD_TIMEOUT, IBS_DISABLE_SSR_TIMEOUT,
CMD_TRANS_TIMEOUT, and IBS_BTSOC_TX_IDLE_TIMEOUT.
IBS_WAKE_RETRANS_TIMEOUT_MS and IBS_HOST_TX_IDLE_TIMEOUT_MS are
intentionally left unchanged. Their values are stored in the struct fields
wake_retrans and tx_idle_delay, which hold ms values at runtime and can be
modified via debugfs. The msecs_to_jiffies() conversion happens at each
call site against the field value, so it cannot be embedded in the macro.
Wake timer depends on commit c347ca17d6
Cc: stable@vger.kernel.org
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When a Bluetooth controller encounters a coredump, it triggers the
Subsystem Restart (SSR) mechanism. The controller first reports the
coredump data and, once the upload is complete, sends a hw_error
event. The host relies on this event to proceed with subsequent
recovery actions.
If the host has not finished processing the coredump data when the
hw_error event is received, it waits until either the processing is
complete or the 8-second timeout expires before handling the event.
The current implementation clears QCA_MEMDUMP_COLLECTION using
clear_bit(), which does not wake up waiters sleeping in
wait_on_bit_timeout(). As a result, the waiting thread may remain
blocked until the timeout expires even if the coredump collection
has already completed.
Fix this by clearing QCA_MEMDUMP_COLLECTION with
clear_and_wake_up_bit(), which also wakes up the waiting thread and
allows the hw_error handling to proceed immediately.
Test case:
- Trigger a controller coredump using:
hcitool cmd 0x3f 0c 26
- Tested on QCA6390.
- Capture HCI logs using btmon.
- Verify that the delay between receiving the hw_error event and
initiating the power-off sequence is reduced compared to the
timeout-based behavior.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On platforms using an M.2 slot with both UART and USB support, bt_en is
pulled high by hardware. In this case, software-based power control
should be disabled. The current platforms are Lemans-EVK and Monaco-EVK.
Add QCA_WCN7850 to the existing condition so that power_ctrl_enabled is
cleared when bt_en is not software-controlled (or absent), aligning its
behavior with WCN6750 and WCN6855
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The WCN39xx family of WiFi/BT chips incorporates a simple PMU, spreading
voltages over internal rails. Implement support for using powersequencer
for this family of QCA devices in addition to using regulators.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The BT core skips calling the hci_dev's shutdown method when the HCI
is unregistered. This means that qca_power_off() was not getting called
leaving BT powered on.
This causes regulators / pwrseq providers to not get disabled which also
causes problem when re-loading the module because regulators and pwrseq
providers have an enablecount which now has never dropped to 0, causing
the BT to not get properly reset between rmmod and re-load which causes
initialization failure on the re-load.
Fix this by calling qca_power_off() from qca_close() when BT has not
already been powered off through a qca_hci_shutdown() call.
hci_ldisc.c will call qca_close() after freeing the hdev, so this
means that qca_power_off() can now no longer deref hu->hdev, change
the logging in qca_power_off() to no longer use hu->hdev.
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The function called qca_power_off() is actually the hci_dev shutdown
handler, rename it to qca_hci_shutdown() to make this clear.
While the qca_power_shutdown() function is actually the counter-part
of qca_power_on() rename it to qca_power_off() to make this clear.
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Whenever new chipset support is added to the driver code,
we ended up adding chipset name to the last of the switch case
arising code readability issue because of improper sorting of
the chipset names in various places of the code.
Refactor code such a way that new chipset can be added easily
in the code without compromising code readability.
Signed-off-by: Vivek Sahu <vivek.sahu@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The setup process previously combined error handling and retry gating
under one condition. As a result, the final failed attempt exited
without performing cleanup.
Update the failure path to always perform power and port cleanup on
setup failure, and reopen the port only when retrying.
Fixes: 9e80587aba ("Bluetooth: hci_qca: Enhance retry logic in qca_setup")
Signed-off-by: Jinwang Li <jinwang.li@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Here is the small amount of tty and serial driver updates for 7.0-rc1.
Nothing major in here at all, just some driver updates and minor tweaks
and cleanups including:
- sh-sci serial driver updates
- 8250 driver updates
- attempt to make the tty ports have their own workqueue, but was
reverted after testing found it to have problems on some platforms.
This will probably come back for 7.1 after it has been reworked and
resubmitted
- other tiny tty driver changes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaZR1VQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfsACghiyMgr0XKVDFEpV7/fPzocKH+o0An3v8knSi
kLz/f6LstVsISqCxeT+9
=uozB
-----END PGP SIGNATURE-----
Merge tag 'tty-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the small amount of tty and serial driver updates for 7.0-rc1.
Nothing major in here at all, just some driver updates and minor
tweaks and cleanups including:
- sh-sci serial driver updates
- 8250 driver updates
- attempt to make the tty ports have their own workqueue, but was
reverted after testing found it to have problems on some platforms.
This will probably come back for 7.1 after it has been reworked and
resubmitted
- other tiny tty driver changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (49 commits)
Revert "tty: tty_port: add workqueue to flip TTY buffer"
tty: tty_port: add workqueue to flip TTY buffer
serial: 8250_pci: Remove custom deprecated baud setting routine
serial: 8250_omap: Remove custom deprecated baud setting routine
dt-bindings: serial: renesas,scif: Document RZ/G3L SoC
serial: 8250: omap: set out-of-band wakeup if wakeup pinctrl exists
tty: hvc-iucv: Remove KMSG_COMPONENT macro
dt-bindings: serial: google,goldfish-tty: Convert to DT schema
dt-bindings: serial: sh-sci: Fold single-entry compatibles into enum
serial: 8250: 8250_omap.c: Clear DMA RX running status only after DMA termination is done
serial: 8250: 8250_omap.c: Add support for handling UART error conditions
serial: SH_SCI: improve "DMA support" prompt
serial: Kconfig: fix ordering of entries for menu display
serial: 8250: fix ordering of entries for menu display
serial: imx: change SERIAL_IMX_CONSOLE to bool
8250_men_mcb: drop unneeded MODULE_ALIAS
serial: men_z135_uart: drop unneeded MODULE_ALIAS
dt-bindings: serial: renesas,rsci: Document RZ/V2H(P) and RZ/V2N SoCs
serial: rsci: Convert to FIELD_MODIFY()
dt-bindings: serial: 8250: add SpacemiT K3 UART compatible
...
Add QCA_CAP_HFP_HW_OFFLOAD capability flag to WCN6855 and WCN7850
device data structures to enable Hands-Free Profile (HFP) hardware
offload support on these Qualcomm Bluetooth chipsets.
Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Replace SoC-specific check with capability-based approach for HFP
hardware offload configuration. Add QCA_CAP_HFP_HW_OFFLOAD capability
flag and support_hfp_hw_offload field to qca_serdev structure. Add
QCA_CAP_HFP_HW_OFFLOAD capability flag to QCA2066 device data
structures.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On QCS9075 and QCA8275 platforms, the BT_EN pin is always pulled up by hw
and cannot be controlled by the host. As a result, in case of a firmware
crash, the host cannot trigger a cold reset. Instead, the BT controller
performs a warm restart on its own, without reloading the firmware.
This leads to the controller remaining in IBS_WAKE state, while the host
expects it to be in sleep mode. The mismatch causes HCI reset commands
to time out. Additionally, the driver does not clear internal flags
QCA_SSR_TRIGGERED and QCA_IBS_DISABLED, which blocks the reset sequence.
If the SSR duration exceeds 2 seconds, the host may enter TX sleep mode
due to tx_idle_timeout, further preventing recovery. Also, memcoredump_flag
is not cleared, so only the first SSR generates a coredump.
Tell the driver that the BT controller has undergone a proper restart sequence:
- Clear QCA_SSR_TRIGGERED and QCA_IBS_DISABLED flags after SSR.
- Add a 50ms delay to allow the controller to complete its warm reset.
- Reset tx_idle_timer to prevent the host from entering TX sleep mode.
- Clear memcoredump_flag to allow multiple coredump captures.
Apply these steps only when HCI_QUIRK_NON_PERSISTENT_SETUP is not set,
which indicates that BT_EN is defined in DTS and cannot be toggled.
Refer to the comment in include/net/bluetooth/hci.h for details on
HCI_QUIRK_NON_PERSISTENT_SETUP.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A different structure is stored in drvdata for the drivers which used
that duplicate function, but h4_recv_buf() assumes drvdata is always an
hci_uart structure.
Consequently, alignment and padding are now randomly corrupted for
btmtkuart, btnxpuart, and bpa10x in h4_recv_buf(), causing erratic
breakage.
Fix this by making the hci_uart structure the explicit argument to
h4_recv_buf(). Every caller already has a reference to hci_uart, and
already obtains the hci_hdev reference through it, so this actually
eliminates a redundant pointer indirection for all existing callers.
Fixes: 93f06f8f0d ("Bluetooth: remove duplicate h4_recv_buf() in header")
Reported-by: Francesco Valla <francesco@valla.it>
Closes: https://lore.kernel.org/lkml/6837167.ZASKD2KPVS@fedora.fritz.box/
Signed-off-by: Calvin Owens <calvin@wbinvd.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Enable ISO data packet RX for LE audio.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The 'quirks' member already ran out of bits on some platforms some time
ago. Replace the integer member by a bitmap in order to have enough bits
in future. Replace raw bit operations by accessor macros.
Fixes: ff26b2dd65 ("Bluetooth: Add quirk for broken READ_VOICE_SETTING")
Fixes: 127881334e ("Bluetooth: Add quirk for broken READ_PAGE_SCAN_TYPE")
Suggested-by: Pauli Virtanen <pav@iki.fi>
Tested-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some modules have BT_EN enabled via a hardware pull-up,
meaning it is not defined in the DTS and is not controlled
through the power sequence. In such cases, fall through
to follow the legacy flow.
Signed-off-by: Shuai Zhang <quic_shuaz@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
Commit 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL
returned by gpiod_get_optional()") accidentally changed the prevous
behavior where power control would be disabled without the BT_EN GPIO
only on QCA_WCN6750 and QCA_WCN6855 while also getting the error check
wrong. We should treat every IS_ERR() return value from
devm_gpiod_get_optional() as a reason to bail-out while we should only
set power_ctrl_enabled to false on the two models mentioned above. While
at it: use dev_err_probe() to save a LOC.
Cc: stable@vger.kernel.org
Fixes: 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL returned by gpiod_get_optional()")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Hsin-chen Chuang <chharry@chromium.org>
Reviewed-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
WCN3950 is another example of the WCN39xx BT/WiFI family of chips. It
requires different firmware files and has different current
requirements, so add it as a separate SoC type.
The firmware for these chips has been recently added to the
linux-firmware repository and will be a part of the upcoming release:
- qca/cmbtfw12.tlv
- qca/cmbtfw13.tlv
- qca/cmnv12.bin
- qca/cmnv13.bin
- qca/cmnv13s.bin
- qca/cmnv13t.bin
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Older boards are having entry "enable-gpios" in dts, we can safely assume
latest boards which are supporting PMU node enrty will support power
sequencer.
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The hdev->reset is never used now and the hdev->cmd_timeout actually
does reset. This patch changes the call path from
hdev->cmd_timeout -> vendor_cmd_timeout -> btusb_reset -> hdev->reset
, to
hdev->reset -> vendor_reset -> btusb_reset
Which makes it clear when we export the hdev->reset to a wider usage
e.g. allowing reset from sysfs.
This patch doesn't introduce any behavior change.
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The firmware-name property has been expanded to specify the names of NVM
and rampatch firmware for certain chips, such as the QCA6698 Bluetooth
chip. Although it shares the same IP core as the WCN6855, the QCA6698
has different RF components and RAM sizes, necessitating new firmware
files. This change allows for the configuration of NVM and rampatch in
DT.
Possible configurations:
firmware-name = QCA6698/hpnv21.bin, QCA6698/hpbtfw21.tlv;
firmware-name = QCA6698/hpnv21, QCA6698/hpbtfw21.tlv;
Signed-off-by: Cheng Jiang <quic_chejiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use the new devm_clk_get_optional_enabled_with_rate() clock helper to
shrink the code a bit.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
On systems in the field, we are seeing this sometimes in the kernel logs:
Bluetooth: qca_controller_memdump() hci0: hci_devcd_init Return:-95
This means that _something_ decided that it wanted to get a memdump
but then hci_devcd_init() returned -EOPNOTSUPP (AKA -95).
The cleanup code in qca_controller_memdump() when we get back an error
from hci_devcd_init() undoes most things but forgets to clear
QCA_IBS_DISABLED. One side effect of this is that, during the next
suspend, qca_suspend() will always get a timeout.
Let's fix it so that we clear the bit.
Fixes: 06d3fdfcdf ("Bluetooth: hci_qca: Add qcom devcoredump support")
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This inverts the LE State quirk so by default we assume the controllers
would report valid states rather than invalid which is how quirks
normally behave, also this would result in HCI command failing it the LE
States are really broken thus exposing the controllers that are really
broken in this respect.
Link: https://github.com/bluez/bluez/issues/584
Fixes: 220915857e ("Bluetooth: Adding driver and quirk defs for multi-role LE")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Unlike qca_regulator_init(), qca_power_shutdown() may be called for
QCA_ROME which does not have qcadev->bt_power assigned. Add a
NULL-pointer check before dereferencing the struct qca_power pointer.
Fixes: eba1718717 ("Bluetooth: hci_qca: make pwrseq calls the default if available")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Closes: https://lore.kernel.org/linux-bluetooth/su3wp6s44hrxf4ijvsdfzbvv4unu4ycb7kkvwbx6ltdafkldir@4g7ydqm2ap5j/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
QCA6390 can albo be used on non-DT systems so we must not make the power
sequencing the only option. Check if the serdev device consumes an OF
node. If so: honor the new contract as per the DT bindings. If not: fall
back to the previous behavior by falling through to the existing
default label.
Fixes: 9a15ce6857 ("Bluetooth: qca: use the power sequencer for QCA6390")
Reported-by: Wren Turkal <wt@penguintechs.org>
Closes: https://lore.kernel.org/linux-bluetooth/27e6a6c5-fb63-4219-be0b-eefa2c116e06@penguintechs.org/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Now that we call pwrseq_power_off() for all models that hold a valid
power sequencing handle, we can remove the switch case for QCA_6390. The
switch will now use the default label for this model but that's fine: if
it has the BT-enable GPIO than we should use it.
Fixes: eba1718717 ("Bluetooth: hci_qca: make pwrseq calls the default if available")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following build error introduced by b80f4e3b8c
("Bluetooth: hci_qca: schedule a devm action for disabling the clock"):
drivers/bluetooth/hci_qca.c: In function ‘qca_serdev_remove’:
drivers/bluetooth/hci_qca.c:2501:2: error: label at end of compound statement
2501 | default:
| ^~~~~~~
Fixes: b80f4e3b8c ("Bluetooth: hci_qca: schedule a devm action for disabling the clock")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In preparation for using the power sequencing subsystem on sm8650 boards
and X13s laptop let's make pwrseq the default for wcn7850 and wcn6855.
Both these models require an enable GPIO so we can safely assume that if
the property is not there, then we should try to get the power
sequencer. Due to how the pwrseq lookup works - checking the provider at
run-time - we cannot really do it the other way around as we'd get stuck
forever on -EPROBE_DEFER.
If the relevant OF node does have the 'enable-gpios' property, we
fallback to the existing code for backward compatibility with older DTs.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the device has a power sequencing handle, use it first. Otherwise
fall back to whatever code already exists.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Now that all three branches of the switch end up doing the same thing,
we can move the call to hci_uart_register_device() past it and unify the
error message.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In preparation for unduplicating the hci_uart registration code,
schedule a devres action for disabling the SUSCLK rather than doing it
manually.
We cannot really use devm_clk_get_enabled() as we also set the rate
before enabling the clock. While this should in theory work, I don't
want to risk breaking existing users. One solution for the future is to
add devm_clk_get_enabled_with_rate() to the clock framework.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
We unnecessarily fallthrough the case for QCA6390 when initializing the
device and hit the condition where - due to the lack of the enable-gpio
- we disable power management despite using the power sequencer. We don't
need to look for clocks on this model so it makes more sense to just
register the hci device and break the switch.
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 9a15ce6857 ("Bluetooth: qca: use the power sequencer for QCA6390")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # RB5
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use the pwrseq subsystem's consumer API to run the power-up sequence for
the Bluetooth module of the QCA6390 package.
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD, SM8650-QRD & SM8650-HDK
Tested-by: Caleb Connolly <caleb.connolly@linaro.org> # OnePlus 8T
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is preferred to use sizeof(*pointer) instead of sizeof(type)
due to the type of the variable can change and one needs not
change the former (unlike the latter). This patch has no effect
on runtime behavior.
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 272970be3d ("Bluetooth: hci_qca: Fix driver shutdown on closed
serdev") will cause below regression issue:
BT can't be enabled after below steps:
cold boot -> enable BT -> disable BT -> warm reboot -> BT enable failure
if property enable-gpios is not configured within DT|ACPI for QCA6390.
The commit is to fix a use-after-free issue within qca_serdev_shutdown()
by adding condition to avoid the serdev is flushed or wrote after closed
but also introduces this regression issue regarding above steps since the
VSC is not sent to reset controller during warm reboot.
Fixed by sending the VSC to reset controller within qca_serdev_shutdown()
once BT was ever enabled, and the use-after-free issue is also fixed by
this change since the serdev is still opened before it is flushed or wrote.
Verified by the reported machine Dell XPS 13 9310 laptop over below two
kernel commits:
commit e00fc2700a3f ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of bluetooth-next tree.
commit b23d98d46d ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of linus mainline tree.
Fixes: 272970be3d ("Bluetooth: hci_qca: Fix driver shutdown on closed serdev")
Cc: stable@vger.kernel.org
Reported-by: Wren Turkal <wt@penguintechs.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218726
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Wren Turkal <wt@penguintechs.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Any return value from gpiod_get_optional() other than a pointer to a
GPIO descriptor or a NULL-pointer is an error and the driver should
abort probing. That being said: commit 56d074d26c ("Bluetooth: hci_qca:
don't use IS_ERR_OR_NULL() with gpiod_get_optional()") no longer sets
power_ctrl_enabled on NULL-pointer returned by
devm_gpiod_get_optional(). Restore this behavior but bail-out on errors.
While at it: also bail-out on error returned when trying to get the
"swctrl" GPIO.
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Closes: https://lore.kernel.org/linux-bluetooth/1713449192-25926-2-git-send-email-quic_zijuhu@quicinc.com/
Fixes: 56d074d26c ("Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Wren Turkal" <wt@penguintechs.org>
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Krzysztof Kozlowski<krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
setup() is called for a non-serdev controller.
Fixes: e9b3e5b8c6 ("Bluetooth: hci_qca: only assign wakeup with serial port support")
Cc: stable@vger.kernel.org # 6.2
Cc: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
wakeup() is called for a non-serdev controller during suspend.
Just return true for now to restore the original behaviour and address
the crash with pre-6.2 kernels, which do not have commit e9b3e5b8c6
("Bluetooth: hci_qca: only assign wakeup with serial port support") that
causes the crash to happen already at setup() time.
Fixes: c1a74160ea ("Bluetooth: hci_qca: Add device_may_wakeup support")
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This was previously believed to be due to lack of persistent storage for
the address but it may also be due to integrators opting to not use the
on-chip OTP memory and instead store the address elsewhere (e.g. in
storage managed by secure world firmware).
According to Qualcomm, at least WCN6750, WCN6855 and WCN7850 have
on-chip OTP storage for the address.
As the device type alone cannot be used to determine when the address is
valid, instead read back the address during setup() and only set the
HCI_QUIRK_USE_BDADDR_PROPERTY flag when needed.
This specifically makes sure that controllers that have been provisioned
with an address do not start as unconfigured.
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Link: https://lore.kernel.org/r/124a7d54-5a18-4be7-9a76-a12017f6cce5@quicinc.com/
Fixes: 5971752de4 ("Bluetooth: hci_qca: Set HCI_QUIRK_USE_BDADDR_PROPERTY for wcn3990")
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Shuai Zhang