The sound device is enabled by default so remove the redundant status.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230127142221.3718184-3-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
For proper warm (re)boot from SD card the BPI-M5 board requires TFLASH_VDD_EN
and VDDIO_C pins to be switched to high impedance mode. This can be achieved
using OPEN_DRAIN instead of ACTIVE_HIGH to leave the GPIO pins in input mode
and retain high state (pin has the pull-up).
This change is inspired by meson-sm1-odroid.dtsi where OPEN_DRAIN has been
used to resolve similar problems with the Odroid C4 board (TF_IO in the C4
dts is the equivalent regulator).
Fixes: 976e920183 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230127142221.3718184-2-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Setting dr_mode to "host" prevents otg which can be useful on a board
with limited connectivity options. So don't force host mode.
Fixes: 26d1400f74 ("arm64: dts: amlogic: add support for Radxa Zero")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230127103913.3386435-1-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
No functional changes.
Adjust to comply with dt-schema requirements
and make it possible to validate values.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20230126193732.69699-1-david@ixit.cz
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added new but not yet supported
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Link: https://lore.kernel.org/r/20230122-topic-odroid-n2l-upstream-initial-v2-3-8d3fea6d403d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In order to introduce Odroid-N2L which is basically an Odroid-N2+
without some on-board peripherals (Ethernet, RTC, Hub, Jack),
move the common nodes into a new meson-g12b-odroid.dtsi which will
will be the common dtsi for all the Odroid-N2 derived boards.
Link: https://lore.kernel.org/r/20230122-topic-odroid-n2l-upstream-initial-v2-2-8d3fea6d403d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230122-topic-odroid-n2l-upstream-initial-v2-1-8d3fea6d403d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add an active trip tied to the on-board fan cooling device, which is better
than describing it along the passive cooling maps.
Fixes: 33b14f663d ("arm64: dts: meson: add initial device-tree for ODROID-HC4")
Reported-by: Ricardo Pardini <ricardo@pardini.net>
Link: https://lore.kernel.org/r/20230124-topic-odroid-hc4-upstream-fix-fan-trip-v1-1-b0c6aa355d93@linaro.org
Tested-by: Ricardo Pardini <ricardo@pardini.net>
[narmstrong: added Ricardo's tested-by from off-list chat]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add initial support for the HDMI and Analogue i2s audio outputs.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230123065834.2670125-1-christianshewitt@gmail.com
[narmstrong: removed useless status property in /sound]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The Broadcom WiFi/BT SDIO nodes are now inherited from the P212 common dtsi
so we can remove them from the VIM1 board dts.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230123065504.2669769-4-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Cosmetic-only change to alpha-sort the pwm_ef node.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230123065504.2669769-3-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The P212 has a combined WiFi/BT module. The BT side is already enabled
in the dtsi but the WiFi side is not. Let's enable the WiFi module.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230123065504.2669769-2-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
mmc-controller.yaml defines "^mmc(@.*)?$" as node name pattern.
In preparation of adding schema-based validation fix the node name
in two affected files.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/55c53e8d-6b30-51bf-edf6-b5b67887bd0a@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Amlogic G12A devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: b190056fa9 ("arm64: dts: meson-g12a: add cpus OPP table")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20230119053031.21400-1-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Node names should be generic and use hyphens instead of underscores to
not cause warnings. Also nodes without a reg property should not have a
unit-address. Change the scpi_dvfs node to use clock-controller as node
name without a unit address (since it does not have a reg property).
Fixes: 70db166a2b ("ARM64: dts: meson-gxbb: Add SCPI with cpufreq & sensors Nodes")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230111211350.1461860-7-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Documentation/devicetree/bindings/net/ethernet-phy.yaml defines that the
node name for Ethernet PHYs should match the following pattern:
^ethernet-phy(@[a-f0-9]+)?$
Replace the underscore with a hyphen to adhere to this binding.
Fixes: 280c17df8f ("arm64: dts: meson: g12a: add mdio multiplexer")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230111211350.1461860-6-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Unit names should use hyphens instead of underscores to not cause
warnings.
Fixes: bfe59f92d3 ("ARM64: dts: amlogic: gxbb: Enable NVMEM")
Suggested-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230111211350.1461860-5-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Node names should use hyphens instead of underscores to not cause
warnings.
Fixes: 59ec069d50 ("arm64: dts: meson-axg: add support for JetHub D1p (j110)")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230111211350.1461860-4-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Node names should use hyphens instead of underscores to not cause
warnings.
Fixes: abfaae24ec ("arm64: dts: meson-gxl: add support for JetHub H1")
Suggested-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230111211350.1461860-3-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Unit addresses should be written using lower-case hex characters. Use
wifi_mac@c to fix a yaml schema validation error once the eFuse
dt-bindings have been converted to a yaml schema:
efuse: Unevaluated properties are not allowed ('wifi_mac@C' was
unexpected)
Also node names should use hyphens instead of underscores as the latter
can also cause warnings.
Fixes: abfaae24ec ("arm64: dts: meson-gxl: add support for JetHub H1")
Acked-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230111211350.1461860-2-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This "NPU" is very similar to the Vivante GPUs and Etnaviv works well
with it with just a few small changes.
v2: Add reference to RESET_NNA (Neil)
v3: Fix indentation (Neil)
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221202115223.39051-5-tomeu.vizoso@collabora.com
[narmstrong: squash patch 8, disable NPU by default and do not enable NPU on vim3 yet]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add define for the NNA power domain for the NPU in the G12A.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221202115223.39051-3-tomeu.vizoso@collabora.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Doesn't appear in the TRM I have, but it is used by the downstream
galcore driver.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221202115223.39051-2-tomeu.vizoso@collabora.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The node names should be generic and DT schema expects certain pattern:
amlogic/meson-sm1-bananapi-m5.dtb: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221125144141.477253-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One driver specific change here which handles the case where a SPI
device for some reason tries to change the bus speed during a message on
fsl_spi hardware, this should be very unusual.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOmIFQACgkQJNaLcl1U
h9BD2Qf/byfpQzO+8mnDIenWP3X/WMNxJybIe1zaZXOEPRdxmE24Q7BvROnu/80C
jiKGJ3x/n5dhgnBvBJYdTw93BwDUJIcoz42WHnJMxRpxHPd/IX9N8NEOtMU5Z7T6
R/9LPpTja33CXXqbvhZw2M1dhVxbEZ9VgPVOemz0nLQtYnM4/Y8wj2RFOGgJFZ91
krY8S7VkLp6ycdv+a9ofMck+l05zpQ7TG54Nmr/0wvexosj7x7JLyZx6CahGL4/E
PMF7MDblLIrCvMtJPs2gpjHTiAReu85akoOvxBcZc5JNNynp8GXmDcOwgPRbZ7pi
bAJzH0LnwPQycTX+e46QMpViyVll7g==
=zqM3
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"One driver specific change here which handles the case where a SPI
device for some reason tries to change the bus speed during a message
on fsl_spi hardware, this should be very unusual"
* tag 'spi-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fsl_spi: Don't change speed while chipselect is active
Two core fixes here, one for a long standing race which some Qualcomm
systems have started triggering with their UFS driver and another fixing
a problem with supply lookup introduced by the fixes for devm related
use after free issues that were introduced in this merge window.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOmHd4ACgkQJNaLcl1U
h9A8hQf/fTezN966/Rp9tvP9YJOPmluqoqDxp/kbyfs3wXlhGR51rytXk/h0DDUD
U8VYIzIyJ7RyqNRtbSqoaNKTCq73Z2/eWl3O/Tsw/mVbpsPHbgDFG4qmM3wE88Rm
u6tOFHouTMQPSJ1yDWJrnR627uRQsnjmJbElSkSWXGWVtJnBqbj+QPGal+hXR/lv
0Fo3nvKvLG5W7GkRh7rRTBu+reJAM4piFQzWxWStiyQwgRLZzpPbgXmpPfto7J5L
WeRMEJkprUVdps+DuylnsHHPD1EA0sBwvs5FQ7yKFuWoejZLC/loW51uColwiIOw
uhQlLzm8WwLePjYQPatHDegxu056fg==
=YhNZ
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Two core fixes here, one for a long standing race which some Qualcomm
systems have started triggering with their UFS driver and another
fixing a problem with supply lookup introduced by the fixes for devm
related use after free issues that were introduced in this merge
window"
* tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: fix deadlock on regulator enable
regulator: core: Fix resolve supply lookup issue
Use "grep -E" instead of "egrep".
-----BEGIN PGP SIGNATURE-----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=m/60
-----END PGP SIGNATURE-----
Merge tag 'coccinelle-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux
Pull coccicheck update from Julia Lawall:
"Modernize use of grep in coccicheck:
Use 'grep -E' instead of 'egrep'"
* tag 'coccinelle-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
scripts: coccicheck: use "grep -E" instead of "egrep"
Fix up the sound code to not pass __GFP_COMP to the non-coherent DMA
allocator, as it copes with that just as badly as the coherent allocator,
and then add a check to make sure no one passes the flag ever again.
-----BEGIN PGP SIGNATURE-----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=q0m6
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-2022-12-23' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Fix up the sound code to not pass __GFP_COMP to the non-coherent DMA
allocator, as it copes with that just as badly as the coherent
allocator, and then add a check to make sure no one passes the flag
ever again"
* tag 'dma-mapping-2022-12-23' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: reject GFP_COMP for noncoherent allocations
ALSA: memalloc: don't use GFP_COMP for non-coherent dma allocations
- improve p9_check_errors to check buffer size instead of msize when possible
(e.g. not zero-copy)
- some more syzbot and KCSAN fixes
- minor headers include cleanup
-----BEGIN PGP SIGNATURE-----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=xLkl
-----END PGP SIGNATURE-----
Merge tag '9p-for-6.2-rc1' of https://github.com/martinetd/linux
Pull 9p updates from Dominique Martinet:
- improve p9_check_errors to check buffer size instead of msize when
possible (e.g. not zero-copy)
- some more syzbot and KCSAN fixes
- minor headers include cleanup
* tag '9p-for-6.2-rc1' of https://github.com/martinetd/linux:
9p/client: fix data race on req->status
net/9p: fix response size check in p9_check_errors()
net/9p: distinguish zero-copy requests
9p/xen: do not memcpy header into req->rc
9p: set req refcount to zero to avoid uninitialized usage
9p/net: Remove unneeded idr.h #include
9p/fs: Remove unneeded idr.h #include
A few more updates for 6.2 since the last PR: most of changes are
about ASoC device-specific fixes.
- Lots of ASoC Intel AVS extensions and refactoring
- Quirks for ASoC Intel SOF as well as regression fixes
- ASoC Mediatek and Rockchip fixes
- Intel HD-audio HDMI workarounds
- Usual HD- and USB-audio device-specific quirks
-----BEGIN PGP SIGNATURE-----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=2Uko
-----END PGP SIGNATURE-----
Merge tag 'sound-6.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound updates from Takashi Iwai:
"A few more updates for 6.2: most of changes are about ASoC
device-specific fixes.
- Lots of ASoC Intel AVS extensions and refactoring
- Quirks for ASoC Intel SOF as well as regression fixes
- ASoC Mediatek and Rockchip fixes
- Intel HD-audio HDMI workarounds
- Usual HD- and USB-audio device-specific quirks"
* tag 'sound-6.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (54 commits)
ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless
ALSA: azt3328: Remove the unused function snd_azf3328_codec_outl()
ASoC: lochnagar: Fix unused lochnagar_of_match warning
ASoC: Intel: Add HP Stream 8 to bytcr_rt5640.c
ASoC: SOF: mediatek: initialize panic_info to zero
ASoC: rt5670: Remove unbalanced pm_runtime_put()
ASoC: Intel: bytcr_rt5640: Add quirk for the Advantech MICA-071 tablet
ASoC: Intel: soc-acpi: update codec addr on 0C11/0C4F product
ASoC: rockchip: spdif: Add missing clk_disable_unprepare() in rk_spdif_runtime_resume()
ASoC: wm8994: Fix potential deadlock
ASoC: mediatek: mt8195: add sof be ops to check audio active
ASoC: SOF: Revert: "core: unregister clients and machine drivers in .shutdown"
ASoC: SOF: Intel: pci-tgl: unblock S5 entry if DMA stop has failed"
ALSA: hda/hdmi: fix stream-id config keep-alive for rt suspend
ALSA: hda/hdmi: set default audio parameters for KAE silent-stream
ALSA: hda/hdmi: fix i915 silent stream programming flow
ALSA: hda: Error out if invalid stream is being setup
ASoC: dt-bindings: fsl-sai: Reinstate i.MX93 SAI compatible string
ASoC: soc-pcm.c: Clear DAIs parameters after stream_active is updated
ASoC: codecs: wcd-clsh: Remove the unused function
...
Christian Hewitt