Add druver for pin controller in Low Power Audio SubSystem (LPASS). The
driver is similar to SM8450 LPASS pin controller, with differences in
few pin groups (qua_mi2s -> i2s0).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230203174645.597053-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to hardware programming guide, the swr_rx_data pin group has
only two pins (GPIO5 and GPIO6). This is also visible in "struct
sm8450_groups" in the driver - GPIO15 does not have swr_rx_data
function.
Fixes: ec1652fc4d ("pinctrl: qcom: Add sm8450 lpass lpi pinctrl driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230203165054.390762-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_kasprintf() instead of kasprintf() to avoid any potential
leaks. At the moment drivers have no remove functionality thus
there is no need for fixes tag.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230203132714.1931596-1-claudiu.beznea@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARM systems are often memory constrained and more often than not
use slow single-channel storage such as flash memory or MMC/SD-cards.
For any interactive systems (such as mobile phones, tablets,
chromebooks...) the BFQ I/O scheduler will be desireable.
Make sure the BFQ I/O scheduler is available on these systems.
Loongarch, MIPS, m68k, UM and S390 has also enabled BFQ in their
defconfigs, cf commit b495dfed70
"um: Cleanup CONFIG_IOSCHED_CFQ" where the motivation is that
it replaces the former CFQ scheduler.
Cc: Paolo Valente <paolo.valente@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230203140404.1125850-1-linus.walleij@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This time around we have a PMGR change to allow IRQ-safe usage, RTKit
crash register dump decoding, and a bunch of RTKit API changes used by
upcoming drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSByI3Ki0mXziclZJcd+FPLCI8zYgUCY9kAQwAKCRAd+FPLCI8z
YhQYAP4km7JfYWsQYKjGSqHounJqgzFnaGFyN3xBmUH3cpyEaQD+IP3vl9PBBWqw
/rrpVlSwfZ6E1VclFTpaE6/KJPDZwwA=
=tXq9
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=HucU
-----END PGP SIGNATURE-----
Merge tag 'asahi-soc-rtkit-pmgr-6.3' of https://github.com/AsahiLinux/linux into soc/drivers
Apple SoC RTKit/PMGR updates for 6.3.
This time around we have a PMGR change to allow IRQ-safe usage, RTKit
crash register dump decoding, and a bunch of RTKit API changes used by
upcoming drivers.
* tag 'asahi-soc-rtkit-pmgr-6.3' of https://github.com/AsahiLinux/linux:
soc: apple: rtkit: Add register dump decoding to crashlog
soc: apple: rtkit: Export non-devm init/free functions
soc: apple: rtkit: Add a private pointer to apple_rtkit_shmem
soc: apple: apple-pmgr-pwrstate: Switch to IRQ-safe mode
soc: apple: rtkit: Add apple_rtkit_idle() function
Link: https://lore.kernel.org/r/4790bdc4-b6e2-228b-771f-023363f65fb3@marcan.st
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
kexec (PPC64) code calls memory_hotplug_max(). Add the header
declaration for it from <asm/mmzone.h>. Using <linux/mmzone.h> does not
work since the #include for <asm/mmzone.h> depends on CONFIG_NUMA=y,
which is not always set.
Fixes this build error/warning:
arch/powerpc/kexec/file_load_64.c: In function 'kexec_extra_fdt_size_ppc64':
arch/powerpc/kexec/file_load_64.c:993:33: error: implicit declaration of function 'memory_hotplug_max'
993 | usm_entries = ((memory_hotplug_max() / drmem_lmb_size()) +
| ^~~~~~~~~~~~~~~~~~
Fixes: fc546faa55 ("powerpc/kexec_file: Count hot-pluggable memory in FDT estimate")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230204172206.7662-1-rdunlap@infradead.org
The "port" comes from the user and if it is zero then the:
ndev = mc->ports[port - 1];
assignment does an out of bounds read. I have changed the if
statement to fix this and to mirror how it is done in
mana_ib_create_qp_rss().
Fixes: 0266a17763 ("RDMA/mana_ib: Add a driver for Microsoft Azure Network Adapter")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y8/3Vn8qx00kE9Kk@kili
Acked-by: Long Li <longli@microsoft.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Pietro Borrello says:
====================
tuntap: correctly initialize socket uid
sock_init_data() assumes that the `struct socket` passed in input is
contained in a `struct socket_alloc` allocated with sock_alloc().
However, tap_open() and tun_chr_open() pass a `struct socket` embedded
in a `struct tap_queue` and `struct tun_file` respectively, both
allocated with sk_alloc().
This causes a type confusion when issuing a container_of() with
SOCK_INODE() in sock_init_data() which results in assigning a wrong
sk_uid to the `struct sock` in input.
Due to the type confusion, both sockets happen to have their uid set
to 0, i.e. root.
While it will be often correct, as tuntap devices require
CAP_NET_ADMIN, it may not always be the case.
Not sure how widespread is the impact of this, it seems the socket uid
may be used for network filtering and routing, thus tuntap sockets may
be incorrectly managed.
Additionally, it seems a socket with an incorrect uid may be returned
to the vhost driver when issuing a get_socket() on a tuntap device in
vhost_net_set_backend().
Fix the bugs by adding and using sock_init_data_uid(), which
explicitly takes a uid as argument.
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
---
Changes in v3:
- Fix the bug by defining and using sock_init_data_uid()
- Link to v2: https://lore.kernel.org/r/20230131-tuntap-sk-uid-v2-0-29ec15592813@diag.uniroma1.it
Changes in v2:
- Shorten and format comments
- Link to v1: https://lore.kernel.org/r/20230131-tuntap-sk-uid-v1-0-af4f9f40979d@diag.uniroma1.it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_init_data() assumes that the `struct socket` passed in input is
contained in a `struct socket_alloc` allocated with sock_alloc().
However, tap_open() passes a `struct socket` embedded in a `struct
tap_queue` allocated with sk_alloc().
This causes a type confusion when issuing a container_of() with
SOCK_INODE() in sock_init_data() which results in assigning a wrong
sk_uid to the `struct sock` in input.
On default configuration, the type confused field overlaps with
padding bytes between `int vnet_hdr_sz` and `struct tap_dev __rcu
*tap` in `struct tap_queue`, which makes the uid of all tap sockets 0,
i.e., the root one.
Fix the assignment by using sock_init_data_uid().
Fixes: 86741ec254 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_init_data() assumes that the `struct socket` passed in input is
contained in a `struct socket_alloc` allocated with sock_alloc().
However, tun_chr_open() passes a `struct socket` embedded in a `struct
tun_file` allocated with sk_alloc().
This causes a type confusion when issuing a container_of() with
SOCK_INODE() in sock_init_data() which results in assigning a wrong
sk_uid to the `struct sock` in input.
On default configuration, the type confused field overlaps with the
high 4 bytes of `struct tun_struct __rcu *tun` of `struct tun_file`,
NULL at the time of call, which makes the uid of all tun sockets 0,
i.e., the root one.
Fix the assignment by using sock_init_data_uid().
Fixes: 86741ec254 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sock_init_data_uid() to explicitly initialize the socket uid.
To initialise the socket uid, sock_init_data() assumes a the struct
socket* sock is always embedded in a struct socket_alloc, used to
access the corresponding inode uid. This may not be true.
Examples are sockets created in tun_chr_open() and tap_open().
Fixes: 86741ec254 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Facilities setup has to be done after "facilities" command line option
parsing, it might set extra or remove existing facilities bits for
testing purposes.
Fixes: bb1520d581 ("s390/mm: start kernel with DAT enabled")
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
KASAN common code is able to handle memory hotplug and create KASAN shadow
memory on a fly. Online memory ranges are available from mem_detect,
use this information to avoid mapping KASAN shadow for standby memory.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
If kernel is build without KASAN support there is a chance that kernel
image is going to be positioned by KASLR code to overlap with identity
mapping page tables.
When kernel is build with KASAN support enabled memory which
is potentially going to be used for page tables and KASAN
shadow mapping is accounted for in KASLR with the use of
kasan_estimate_memory_needs(). Split this function and introduce
vmem_estimate_memory_needs() to cover decompressor's vmem identity
mapping page tables.
Fixes: bb1520d581 ("s390/mm: start kernel with DAT enabled")
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Add a function to get online memory in total. It is supposed to be used
in the decompressor as well as during early kernel startup.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Introduce mem_detect_truncate() to cut any online memory ranges above
established identity mapping size, so that mem_detect users wouldn't
have to do it over and over again.
Suggested-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Allocation of mem_detect extended area was not considered neither
in commit 9641b8cc73 ("s390/ipl: read IPL report at early boot")
nor in commit b2d24b97b2 ("s390/kernel: add support for kernel address
space layout randomization (KASLR)"). As a result mem_detect extended
theoretically may overlap with ipl report or randomized kernel image
position. But as mem_detect code will allocate extended area only
upon exceeding 255 online regions (which should alternate with offline
memory regions) it is not seen in practice.
To make sure mem_detect extended area does not overlap with ipl report
or randomized kernel position extend usage of "safe_addr". Make initrd
handling and mem_detect extended area allocation code move it further
right and make KASLR takes in into consideration as well.
Fixes: 9641b8cc73 ("s390/ipl: read IPL report at early boot")
Fixes: b2d24b97b2 ("s390/kernel: add support for kernel address space layout randomization (KASLR)")
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In case sclp_early_get_memsize() fails but diag260() succeeds make sure
some sane value is returned. This error scenario is highly unlikely,
but this change makes system able to boot in such case.
Suggested-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Get rid of this sparse warning:
arch/s390/kernel/diag.c:69:29: warning: symbol '__diag8c_tmp_amode31' was not declared. Should it be static?
Fixes: fbaee7464f ("s390/tty3270: add support for diag 8c")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Compiling the kernel with CONFIG_KPROBES disabled, but CONFIG_RETHOOK
enabled, results in this sparse warning:
arch/s390/kernel/rethook.c:26:15: warning: no previous prototype for 'arch_rethook_trampoline_callback' [-Wmissing-prototypes]
26 | unsigned long arch_rethook_trampoline_callback(struct pt_regs *regs)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Add a local rethook header file similar to riscv to address this.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1a280f48c0 ("s390/kprobes: replace kretprobe with rethook")
Link: https://lore.kernel.org/all/202302030102.69dZIuJk-lkp@intel.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Kasan shadow memory area has been moved to the end of kernel address
space since commit 9a39abb7c9 ("s390/boot: simplify and fix kernel
memory layout setup"), therefore skipping any memory ranges above
VMALLOC_START in empty page tables cleanup code already handles
KASAN shadow memory intersection case and explicit checks could be
removed.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Commit b9ff81003c ("s390/vmem: cleanup empty page tables") introduced
empty page tables cleanup in vmem code, but when the kernel is built
with KASAN enabled the code has no effect due to wrong KASAN shadow
memory intersection condition, which effectively ignores any memory
range below KASAN shadow. Fix intersection condition to make code
work as anticipated.
Fixes: b9ff81003c ("s390/vmem: cleanup empty page tables")
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Kasan shadow memory area has been moved to the end of kernel address
space since commit 9a39abb7c9 ("s390/boot: simplify and fix kernel
memory layout setup"). Change kasan memory layout note accordingly.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Currently if for some reason sclp_early_read_info() fails,
sclp_early_get_memsize() will not set max_physmem_end and it
will stay uninitialized. Any garbage value other than 0 will lead
to detect_memory() taking wrong path or returning a garbage value
as max_physmem_end. To avoid that simply initialize max_physmem_end.
Fixes: 73045a08cf ("s390: unify identity mapping limits handling")
Reported-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In the current code each reipl type implements its own pair of loadparm
show/store functions. Add a macro to deduplicate the code a bit.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Fixes: 87fd22e0ae ("s390/ipl: add eckd support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Vladimir Oltean says:
====================
net: ENETC mqprio/taprio cleanup
Please excuse the increased patch set size compared to v4's 15 patches,
but Claudiu stirred up the pot :) when he pointed out that the mqprio
TXQ validation procedure is still incorrect, so I had to fix that, and
then do some consolidation work so that taprio doesn't duplicate
mqprio's bugs. Compared to v4, 3 patches are new and 1 was dropped for now
("net/sched: taprio: mask off bits in gate mask that exceed number of TCs"),
since there's not really much to gain from it. Since the previous patch
set has largely been reviewed, I hope that a delta overview will help
and make up for the large size.
v4->v5:
- new patches:
"[08/17] net/sched: mqprio: allow reverse TC:TXQ mappings"
"[11/17] net/sched: taprio: centralize mqprio qopt validation"
"[12/17] net/sched: refactor mqprio qopt reconstruction to a library function"
- changed patches worth revisiting:
"[09/17] net/sched: mqprio: allow offloading drivers to request queue
count validation"
v4 at:
https://patchwork.kernel.org/project/netdevbpf/cover/20230130173145.475943-1-vladimir.oltean@nxp.com/
v3->v4:
- adjusted patch 07/15 to not remove "#include <net/pkt_sched.h>" from
ti cpsw
https://patchwork.kernel.org/project/netdevbpf/cover/20230127001516.592984-1-vladimir.oltean@nxp.com/
v2->v3:
- move min_num_stack_tx_queues definition so it doesn't conflict with
the ethtool mm patches I haven't submitted yet for enetc (and also to
make use of a 4 byte hole)
- warn and mask off excess TCs in gate mask instead of failing
- finally CC qdisc maintainers
v2 at:
https://patchwork.kernel.org/project/netdevbpf/patch/20230126125308.1199404-16-vladimir.oltean@nxp.com/
v1->v2:
- patches 1->4 are new
- update some header inclusions in drivers
- fix typo (said "taprio" instead of "mqprio")
- better enetc mqprio error handling
- dynamically reconstruct mqprio configuration in taprio offload
- also let stmmac and tsnep use per-TXQ gate_mask
v1 (RFC) at:
https://patchwork.kernel.org/project/netdevbpf/cover/20230120141537.1350744-1-vladimir.oltean@nxp.com/
The main goal of this patch set is to make taprio pass the mqprio queue
configuration structure down to ndo_setup_tc() - patch 13/17. But mqprio
itself is not in the best shape currently, so there are some
consolidation patches on that as well.
Next, there are some consolidation patches in the enetc driver's
handling of TX queues and their traffic class assignment. Then, there is
a consolidation between the TX queue configuration for mqprio and
taprio.
Finally, there is a change in the meaning of the gate_mask passed by
taprio through ndo_setup_tc(). We introduce a capability through which
drivers can request the gate mask to be per TXQ. The default is changed
so that it is per TC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We assume that the mqprio queue configuration from taprio has a simple
1:1 mapping between prio and traffic class, and one TX queue per TC.
That might not be the case. Actually parse and act upon the mqprio
config.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regardless of the requested queue count per traffic class, the enetc
driver allocates a number of TX rings equal to the number of TCs, and
hardcodes a queue configuration of "1@0 1@1 ... 1@max-tc". Other
configurations are silently ignored and treated the same.
Improve that by allowing what the user requests to be actually
fulfilled. This allows more than one TX ring per traffic class.
For example:
$ tc qdisc add dev eno0 root handle 1: mqprio num_tc 4 \
map 0 0 1 1 2 2 3 3 queues 2@0 2@2 2@4 2@6
[ 146.267648] fsl_enetc 0000:00:00.0 eno0: TX ring 0 prio 0
[ 146.273451] fsl_enetc 0000:00:00.0 eno0: TX ring 1 prio 0
[ 146.283280] fsl_enetc 0000:00:00.0 eno0: TX ring 2 prio 1
[ 146.293987] fsl_enetc 0000:00:00.0 eno0: TX ring 3 prio 1
[ 146.300467] fsl_enetc 0000:00:00.0 eno0: TX ring 4 prio 2
[ 146.306866] fsl_enetc 0000:00:00.0 eno0: TX ring 5 prio 2
[ 146.313261] fsl_enetc 0000:00:00.0 eno0: TX ring 6 prio 3
[ 146.319622] fsl_enetc 0000:00:00.0 eno0: TX ring 7 prio 3
$ tc qdisc del dev eno0 root
[ 178.238418] fsl_enetc 0000:00:00.0 eno0: TX ring 0 prio 0
[ 178.244369] fsl_enetc 0000:00:00.0 eno0: TX ring 1 prio 0
[ 178.251486] fsl_enetc 0000:00:00.0 eno0: TX ring 2 prio 0
[ 178.258006] fsl_enetc 0000:00:00.0 eno0: TX ring 3 prio 0
[ 178.265038] fsl_enetc 0000:00:00.0 eno0: TX ring 4 prio 0
[ 178.271557] fsl_enetc 0000:00:00.0 eno0: TX ring 5 prio 0
[ 178.277910] fsl_enetc 0000:00:00.0 eno0: TX ring 6 prio 0
[ 178.284281] fsl_enetc 0000:00:00.0 eno0: TX ring 7 prio 0
$ tc qdisc add dev eno0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 1
[ 186.113162] fsl_enetc 0000:00:00.0 eno0: TX ring 0 prio 0
[ 186.118764] fsl_enetc 0000:00:00.0 eno0: TX ring 1 prio 1
[ 186.124374] fsl_enetc 0000:00:00.0 eno0: TX ring 2 prio 2
[ 186.130765] fsl_enetc 0000:00:00.0 eno0: TX ring 3 prio 3
[ 186.136404] fsl_enetc 0000:00:00.0 eno0: TX ring 4 prio 4
[ 186.142049] fsl_enetc 0000:00:00.0 eno0: TX ring 5 prio 5
[ 186.147674] fsl_enetc 0000:00:00.0 eno0: TX ring 6 prio 6
[ 186.153305] fsl_enetc 0000:00:00.0 eno0: TX ring 7 prio 7
The driver used to set TC_MQPRIO_HW_OFFLOAD_TCS, near which there is
this comment in the UAPI header:
TC_MQPRIO_HW_OFFLOAD_TCS, /* offload TCs, no queue counts */
which is what enetc was doing up until now (and no longer is; we offload
queue counts too), remove that assignment.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enetc driver does not validate the mqprio queue configuration, so it
currently allows things like this:
$ tc qdisc add dev swp0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 3@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 1
But also things like this, completely omitting the queue configuration:
$ tc qdisc add dev eno0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 hw 1
By requesting validation via the mqprio capability structure, this is no
longer allowed, and we bring what is accepted by hardware in line with
what is accepted by software.
The check that num_tc <= real_num_tx_queues also becomes superfluous and
can be dropped, because mqprio_validate_queue_counts() validates that no
TXQ range exceeds real_num_tx_queues. That is a stronger check, because
there is at least 1 TXQ per TC, so there are at least as many TXQs as TCs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 classes of in-tree drivers currently:
- those who act upon struct tc_taprio_sched_entry :: gate_mask as if it
holds a bit mask of TXQs
- those who act upon the gate_mask as if it holds a bit mask of TCs
When it comes to the standard, IEEE 802.1Q-2018 does say this in the
second paragraph of section 8.6.8.4 Enhancements for scheduled traffic:
| A gate control list associated with each Port contains an ordered list
| of gate operations. Each gate operation changes the transmission gate
| state for the gate associated with each of the Port's traffic class
| queues and allows associated control operations to be scheduled.
In typically obtuse language, it refers to a "traffic class queue"
rather than a "traffic class" or a "queue". But careful reading of
802.1Q clarifies that "traffic class" and "queue" are in fact
synonymous (see 8.6.6 Queuing frames):
| A queue in this context is not necessarily a single FIFO data structure.
| A queue is a record of all frames of a given traffic class awaiting
| transmission on a given Bridge Port. The structure of this record is not
| specified.
i.o.w. their definition of "queue" isn't the Linux TX queue.
The gate_mask really is input into taprio via its UAPI as a mask of
traffic classes, but taprio_sched_to_offload() converts it into a TXQ
mask.
The breakdown of drivers which handle TC_SETUP_QDISC_TAPRIO is:
- hellcreek, felix, sja1105: these are DSA switches, it's not even very
clear what TXQs correspond to, other than purely software constructs.
Only the mqprio configuration with 8 TCs and 1 TXQ per TC makes sense.
So it's fine to convert these to a gate mask per TC.
- enetc: I have the hardware and can confirm that the gate mask is per
TC, and affects all TXQs (BD rings) configured for that priority.
- igc: in igc_save_qbv_schedule(), the gate_mask is clearly interpreted
to be per-TXQ.
- tsnep: Gerhard Engleder clarifies that even though this hardware
supports at most 1 TXQ per TC, the TXQ indices may be different from
the TC values themselves, and it is the TXQ indices that matter to
this hardware. So keep it per-TXQ as well.
- stmmac: I have a GMAC datasheet, and in the EST section it does
specify that the gate events are per TXQ rather than per TC.
- lan966x: again, this is a switch, and while not a DSA one, the way in
which it implements lan966x_mqprio_add() - by only allowing num_tc ==
NUM_PRIO_QUEUES (8) - makes it clear to me that TXQs are a purely
software construct here as well. They seem to map 1:1 with TCs.
- am65_cpsw: from looking at am65_cpsw_est_set_sched_cmds(), I get the
impression that the fetch_allow variable is treated like a prio_mask.
This definitely sounds closer to a per-TC gate mask rather than a
per-TXQ one, and TI documentation does seem to recomment an identity
mapping between TCs and TXQs. However, Roger Quadros would like to do
some testing before making changes, so I'm leaving this driver to
operate as it did before, for now. Link with more details at the end.
Based on this breakdown, we have 5 drivers with a gate mask per TC and
4 with a gate mask per TXQ. So let's make the gate mask per TXQ the
opt-in and the gate mask per TC the default.
Benefit from the TC_QUERY_CAPS feature that Jakub suggested we add, and
query the device driver before calling the proper ndo_setup_tc(), and
figure out if it expects one or the other format.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20230202003621.2679603-15-vladimir.oltean@nxp.com/#25193204
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Siddharth Vadapalli <s-vadapalli@ti.com>
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The taprio qdisc does not currently pass the mqprio queue configuration
down to the offloading device driver. So the driver cannot act upon the
TXQ counts/offsets per TC, or upon the prio->tc map. It was probably
assumed that the driver only wants to offload num_tc (see
TC_MQPRIO_HW_OFFLOAD_TCS), which it can get from netdev_get_num_tc(),
but there's clearly more to the mqprio configuration than that.
I've considered 2 mechanisms to remedy that. First is to pass a struct
tc_mqprio_qopt_offload as part of the tc_taprio_qopt_offload. The second
is to make taprio actually call TC_SETUP_QDISC_MQPRIO, *in addition to*
TC_SETUP_QDISC_TAPRIO.
The difference is that in the first case, existing drivers (offloading
or not) all ignore taprio's mqprio portion currently, whereas in the
second case, we could control whether to call TC_SETUP_QDISC_MQPRIO,
based on a new capability. The question is which approach would be
better.
I'm afraid that calling TC_SETUP_QDISC_MQPRIO unconditionally (not based
on a taprio capability bit) would risk introducing regressions. For
example, taprio doesn't populate (or validate) qopt->hw, as well as
mqprio.flags, mqprio.shaper, mqprio.min_rate, mqprio.max_rate.
In comparison, adding a capability is functionally equivalent to just
passing the mqprio in a way that drivers can ignore it, except it's
slightly more complicated to use it (need to set the capability).
Ultimately, what made me go for the "mqprio in taprio" variant was that
it's easier for offloading drivers to interpret the mqprio qopt slightly
differently when it comes from taprio vs when it comes from mqprio,
should that ever become necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The taprio qdisc will need to reconstruct a struct tc_mqprio_qopt from
netdev settings once more in a future patch, but this code was already
written twice, once in taprio and once in mqprio.
Refactor the code to a helper in the common mqprio library.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a lot of code in taprio which is "borrowed" from mqprio.
It makes sense to put a stop to the "borrowing" and start actually
reusing code.
Because taprio and mqprio are built as part of different kernel modules,
code reuse can only take place either by writing it as static inline
(limiting), putting it in sch_generic.o (not generic enough), or
creating a third auto-selectable kernel module which only holds library
code. I opted for the third variant.
In a previous change, mqprio gained support for reverse TC:TXQ mappings,
something which taprio still denies. Make taprio use the same validation
logic so that it supports this configuration as well.
The taprio code didn't enforce TXQ overlaps in txtime-assist mode and
that looks intentional, even if I've no idea why that might be. Preserve
that, but add a comment.
There isn't any dedicated MAINTAINERS entry for mqprio, so nothing to
update there.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make mqprio more user-friendly, create netlink extended ack messages
which say exactly what is wrong about the queue counts. This uses the
new support for printf-formatted extack messages.
Example:
$ tc qdisc add dev eno0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 3@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
Error: sch_mqprio: TC 0 queues 3@0 overlap with TC 1 queues 1@1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mqprio_parse_opt() proudly has a comment:
/* If hardware offload is requested we will leave it to the device
* to either populate the queue counts itself or to validate the
* provided queue counts.
*/
Unfortunately some device drivers did not get this memo, and don't
validate the queue counts, or populate them.
In case drivers don't want to populate the queue counts themselves, just
act upon the requested configuration, it makes sense to introduce a tc
capability, and make mqprio query it, so they don't have to do the
validation themselves.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By imposing that the last TXQ of TC i is smaller than the first TXQ of
any TC j (j := i+1 .. n), mqprio imposes a strict ordering condition for
the TXQ indices (they must increase as TCs increase).
Claudiu points out that the complexity of the TXQ count validation is
too high for this logic, i.e. instead of iterating over j, it is
sufficient that the TXQ indices of TC i and i + 1 are ordered, and that
will eventually ensure global ordering.
This is true, however it doesn't appear to me that is what the code
really intended to do. Instead, based on the comments, it just wanted to
check for overlaps (and this isn't how one does that).
So the following mqprio configuration, which I had recommended to
Vinicius more than once for igb/igc (to account for the fact that on
this hardware, lower numbered TXQs have higher dequeue priority than
higher ones):
num_tc 4 map 0 1 2 3 queues 1@3 1@2 1@1 1@0
is in fact denied today by mqprio.
The full story is that in fact, it's only denied with "hw 0"; if
hardware offloading is requested, mqprio defers TXQ range overlap
validation to the device driver (a strange decision in itself).
This is most certainly a bug, but it's not one that has any merit for
being fixed on "stable" as far as I can tell. This is because mqprio
always rejected a configuration which was in fact valid, and this has
shaped the way in which mqprio configuration scripts got built for
various hardware (see igb/igc in the link below). Therefore, one could
consider it to be merely an improvement for mqprio to allow reverse
TC:TXQ mappings.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20230130173145.475943-9-vladimir.oltean@nxp.com/#25188310
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20230128010719.2182346-6-vladimir.oltean@nxp.com/#25186442
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mqprio is a scheduler and not a classifier, move its offload
structure to pkt_sched.h, where struct tc_taprio_qopt_offload also lies.
Also update some header inclusions in drivers that access this
structure, to the best of my abilities.
Cc: Igor Russkikh <irusskikh@marvell.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: Daniel Machon <daniel.machon@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some more logic will be added to mqprio offloading, so split that code
up from mqprio_init(), which is already large, and create a new
function, mqprio_enable_offload(), similar to taprio_enable_offload().
Also create the opposite function mqprio_disable_offload().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mqprio_init() is quite large and unwieldy to add more code to.
Split the netlink attribute parsing to a dedicated function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQs are currently requested before the netdevice is registered
and a proper name is assigned to the device. Changing interrupt
name to avoid using the format string in the name.
Interrupt name before change: eth%d-ntfy-block.<blk_id>
Interrupt name after change: gve-ntfy-blk<blk_id>@pci:<pci_name>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
net: implement devlink reload in ice
Michal Swiatkowski says:
This is a part of changes done in patchset [0]. Resource management is
kind of controversial part, so I split it into two patchsets.
It is the first one, covering refactor and implement reload API call.
The refactor will unblock some of the patches needed by SIOV or
subfunction.
Most of this patchset is about implementing driver reload mechanism.
Part of code from probe and rebuild is used to not duplicate code.
To allow this reuse probe and rebuild path are split into smaller
functions.
Patch "ice: split ice_vsi_setup into smaller functions" changes
boolean variable in function call to integer and adds define
for it. Instead of having the function called with true/false now it
can be called with readable defines ICE_VSI_FLAG_INIT or
ICE_VSI_FLAG_NO_INIT. It was suggested by Jacob Keller and probably this
mechanism will be implemented across ice driver in follow up patchset.
Previously the code was reviewed here [0].
[0] https://lore.kernel.org/netdev/Y3ckRWtAtZU1BdXm@unreal/T/#m3bb8feba0a62f9b4cd54cd94917b7e2143fc2ecd
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Krzysztof Kozlowski