Add support for SONY Xperia 1 and 5 smartphones, both based on the
Qualcomm SM8150 chipset. There also exist 5G-capable versions of these
devices, but they weren't sold much (if at all) outside Japan.
The devices are affected by a scary UFS behaviour where sending a certain UFS
command (which is worked around on downstream) renders the device unbootable,
by effectively erasing the bootloader. Therefore UFS AND UFSPHY are strictly
disabled for now.
Downstream workaround:
2e7a9ee1c9
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org> (On Bahamut)
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210611203301.101067-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Components that rely on proprietary (not to mention signed!) firmware should
not be enabled by default, as lack of the aforementioned firmware could cause
various issues, from random errors to straight-up failing to boot.
Not enabling modem back on the HDK, as it uses a sa8150.
Also fixed a sorting mistake in both boards' dt while at it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210611203301.101067-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Components that rely on proprietary (not to mention signed!) firmware should
not be enabled by default, as lack of the aforementioned firmware could cause
various issues, from random errors to straight-up failing to boot.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210612192358.62602-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the aforementioned properties in the SoC DTSI so that everybody doesn't
have to copy that into their device DTs, effectively reducing code
duplication.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210613114356.82358-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DPU/MDSS is borderline useless without MDP, so disabling
both of them makes little sense. With this change, enabling
mdss will be enough.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210613110635.46537-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
SA8155p-adp board is based on Qualcomm Snapdragon sa8155p
SoC which is similar to the sm8150 SoC.
Add support for the same in dt-bindings.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210615074543.26700-5-bhupesh.sharma@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
sm8150-mtp board is based on Qualcomm Snapdragon sm8150
SoC.
Add support for the same in dt-bindings.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210615074543.26700-4-bhupesh.sharma@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The calculations for the DLL register values are based on the clock rate
of the reference clock. Provide the reference clock in the definition of
the two SDHCI controllers to not rely on the default values.
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Link: https://lore.kernel.org/r/1623309107-27833-1-git-send-email-sbhanu@codeaurora.org
[bjorn: Rewrote commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the DT nodes for the network-on-chip interconnect buses found
on sc7280-based platforms.
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Link: https://lore.kernel.org/r/1619517059-12109-4-git-send-email-okukatla@codeaurora.org
[bjorn: Sorted nodes and dropped include]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Huawei Ascend G7 supports NFC using the NXP PN547, which is
supported by the nxp-nci-i2c driver in mainline. It seems to detect
NFC tags using "nfctool" just fine, although it seems like there
are not really any useful applications making use of the Linux NFC
subsystem. :(
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The display on the Huawei Ascend G7 is supplied by a TI TPS65132
regulator. The panel needs a driver in mainline first, but the
TPS65132 is already supported in mainline by the tps65132 driver.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Huawei Ascend G7 has a Synaptics "C199HW-006" touchscreen,
supplied by pm8916_l17 and pm8916_l16. Add it to the device tree
and reduce the maximum allowed voltage for pm8916_l16 to 1.8V since
we really should not use more for an I/O supply.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Huawei Ascend G7 is a smartphone from Huawei based on MSM8916.
It's fairly similar to the other MSM8916 devices, the only notable
exception are the "cd-gpios" for detecting if a SD card was inserted:
It looks like Huawei forgot to re-route this to gpio38, so the correct
GPIO seems to be gpio56 on this device.
Note: The original firmware from Huawei can only boot 32-bit kernels.
To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
with EDL, e.g. taken from the DragonBoard 410c. This works because Huawei
forgot to set up (firmware) secure boot for some reason.
Also note that Huawei no longer provides bootloader unlock codes.
This can be bypassed by patching the bootloader from a custom HYP firmware,
making it think the bootloader is unlocked. I use a modified version of
qhypstub [1], that patches a single instruction in the Huawei bootloader.
The device tree contains initial support for the Huawei Ascend G7 with:
- UART (untested, probably available via some test points)
- eMMC/SD card
- Buttons
- Notification LED (combination of 3 GPIO LEDs)
- Vibrator
- WiFi/Bluetooth (WCNSS)
- USB
[1]: https://github.com/msm8916-mainline/qhypstub
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This spi flash part is actually being clocked at 37.5MHz, not 25MHz,
because of the way the clk driver is rounding up the rate that is
requested to the nearest supported frequency. Let's update the frequency
here, and remove the TODO because this is the fastest frequency we're
going to be able to use here.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210519054030.3217704-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This compatible string isn't present upstream. Let's drop the node as it
isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601185959.3101132-2-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This compatible string isn't present upstream. Let's drop the node as it
isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601185959.3101132-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We don't use the PON module on Trogdor devices. Instead the reboot
reason is sort of stored in the 'eventlog' and the bootloader figures
out if the boot is abnormal and records that there. Disable the PON node
and then drop the power key disabling because that's a child node that
will no longer be enabled if the PON node is disabled.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601184417.3020834-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On coachz it could be observed that SPI_CLK voltage level was only
1.4V during active transfers because the drive strength was too
weak. The line hadn't finished slewing up by the time we started
driving it down again. Using a drive strength of 8 lets us achieve the
correct voltage level of 1.8V.
Though the worst problems were observed on coachz hardware, let's do
this across the board for trogdor devices. Scoping other boards shows
that this makes the clk line look nicer on them too and doesn't
introduce any problems.
Only the clk line is adjusted, not any data lines. Because SPI isn't a
DDR protocol we only sample the data lines on either rising or falling
edges, not both. That means the clk line needs to toggle twice as fast
as data lines so having the higher drive strength is more important
there.
Signed-off-by: Wenchao Han <hanwenchao@huaqin.corp-partner.google.com>
[dianders: Adjust author real name; adjust commit message]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210510075253.1.Ib4c296d6ff9819f26bcaf91e8a08729cc203fed0@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Microsoft Surface Duo is based on SM8150 chipset. This new Device Tree
is a copy of sm8150-mtp with a the addition of the volume up key and
relevant i2c nodes.
Signed-off-by: Felipe Balbi <felipe.balbi@microsoft.com>
Link: https://lore.kernel.org/r/20210603122923.1919624-1-balbi@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some SC7180 based boards do not have external pull-up for cd-gpio.
Set this pin to internal pull-up for sleep config to avoid frequent
regulator toggle events.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210602121313.v3.2.I52f30ddfe62041b7e6c3c362f0ad8f695ac28224@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 both have a Samsung S3FWRN5 NFC chip that
works quite well with the s3fwrn5 driver in the Linux NFC subsystem.
The clock setup for the NFC chip is a bit special (although this
seems to be a common approach used for Qualcomm devices with NFC):
The NFC chip has an output GPIO that is asserted whenever the clock
is needed to function properly. On the A3/A5 this is wired up to
PM8916 GPIO2, which is then configured with a special function
(NFC_CLK_REQ or BB_CLK2_REQ).
Enabling the rpmcc RPM_SMD_BB_CLK2_PIN clock will then instruct
PM8916 to automatically enable the clock whenever the NFC chip
requests it. The advantage is that the clock is only enabled when
needed and we don't need to manage it ourselves from the NFC driver.
Note that for some reason Samsung decided to connect the I2C pins
to GPIOs where no hardware I2C bus is available, so we need to
fall back to software bit-banging with i2c-gpio.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 use a Richtek RT5033 PMIC as battery
fuel gauge, charger, flash LED and for some regulators. For now,
only add the fuel gauge/battery device to the device tree,
so we can check the remaining battery percentage.
The other RT5033 drivers need some more work first before
they can be used properly.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On the Samsung Galaxy A5 the touch key is supplied by a single fixed
regulator (enabled via GPIO 97) that supplies both MCU and LED.
Add it to the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The touch key MCU and LED is supplied by two separate fixed regulators
that can be enabled through GPIO 86 and 60. Add them to the device tree.
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
[stephan: extend commit message]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 both have two capacitive touch keys,
connected to an ABOV MCU. It implements the same interface as
implemented by the tm2-touchkey driver and works just fine with
the coreriver,tc360-touchkey compatible. It's probably actually some
Samsung-specific interface that they implement with different MCUs.
Note that for some reason Samsung decided to connect this to GPIOs
where no hardware I2C bus is available, so we need to fall back
to software bit-banging using i2c-gpio.
The vdd/vcc-supply is board-specific and will be added separately
for a3u/a5u.
Co-developed-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a thermal zone for the pm6150 on-die temperature. The system should
try to shut down orderly when the temperature reaches the critical trip
point at 115°C, otherwise the PMIC will perform a HW power off at 145°C.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210603081215.v2.1.Id4510e9e4baaa3f6c9fdd5cdf4d8606e63c262e3@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Adds label for MI2S secondary block to allow follower projects to override
for the four speaker support which uses I2S SD1 line on gpio52 pin.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20210601022117.4071117-1-judyhsiao@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The sc7280 IDP board is also called senor in the Chrome OS builds.
Add the "google,senor" compatible so coreboot/depthcharge knows what
device tree blob to pick
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1619674827-26650-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Document the google,senor board based on sc7280 SoC
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1619674827-26650-1-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add WPSS remote processor client index to Inter-Processor Communication
Controller (IPCC) block.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1619508824-14413-2-git-send-email-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move rmtfs memory region so that it does not overlap with system
RAM (kernel data) when KAsan is enabled. This puts rmtfs right
after mba_mem which is not supposed to increase beyond 0x94600000
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210514113430.1.Ic2d032cd80424af229bb95e2c67dd4de1a70cb0c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for the video, gpu, display, lpass clock controller
device nodes for SC7280 SoC.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1618020280-5470-3-git-send-email-tdas@codeaurora.org
[bjorn: Dropped includes, as they are not present in v5.13-rc1]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add ADC and thermal monitor configuration for skin temperature,
plus a thermal zone that monitors the skin temperature and uses
the big cores as cooling devices.
CoachZ rev1 is stuffed with an incompatible thermistor for the
skin temperature, disable the thermal zone for rev1 to avoid
the use of bogus temperature values.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210414111007.v1.1.I1a438604a79025307f177347d45815987b105cb5@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As per Dmitry Baryshkov [1]:
a) The 2nd "reg" should be 0x3c because "Offset 0x38 is
USB3_DP_COM_REVISION_ID3 (not used by the current driver though)."
b) The 3rd "reg" "is a serdes region and qmp_v3_dp_serdes_tbl contains
registers 0x148 and 0x154."
I think because the 3rd "reg" is a serdes region we should just use
the same size as the 1st "reg"?
[1] https://lore.kernel.org/r/ee5695bb-a603-0dd5-7a7f-695e919b1af1@linaro.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Fixes: 58fd7ae621 ("arm64: dts: qcom: sc7180: Update dts for DP phy inside QMP phy")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210315103836.1.I9a97120319d43b42353aeac4d348624d60687df7@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use sm8250 compatibles instead of sdm845 compatibles
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210329120051.3401567-5-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be enabling HPD
when it isn't supposed to be used. Presumably this board isn't using hpd
on the bridge.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Steev Klimaszewski <steev@kali.org>
Fixes: 956e9c85f4 ("arm64: dts: qcom: c630: Define eDP bridge and panel")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324231424.2890039-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210324204836.29668-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be wasting power
powering hpd when we don't use it on trogdor boards. We didn't notice
this before because the kernel driver blindly disables hpd, but that
won't be true for much longer.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324025534.1837405-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reserve GPIO pins 85-88 as these aren't meant to be accessible from the
application CPUs (causes reboot). Yet another fix similar to
9134586715, 5f8d3ab136, which is needed to allow angler to boot after
3edfb7bd76 ("gpiolib: Show correct direction from the beginning").
Fixes: feeaf56ac7 ("arm64: dts: msm8994 SoC and Huawei Angler (Nexus 6P) support")
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210415193913.1836153-1-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix the compatible to make the driver probe and tell the
driver where to look for the "xo" clock to make sure everything
works.
Then we get a happy (eh, happier) 8996:
somainline-sdcard:/home/konrad# cat /sys/kernel/debug/clk/pwrcl_pll/clk_rate
1152000000
Don't backport without "arm64: dts: qcom: msm8996: Add CPU opps", as
the system fails to boot without consumers for these clocks.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210527192958.775434-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the operating points capabilities of the kryo CPUs, that can be
used for frequency scaling. There are two differents operating point
tables, one for the big cluster and one for the LITTLE cluster.
This frequency scaling support can then be used as a passive cooling
device (cpufreq cooling device).
Only add nominal fmax for now, since there is no dynamic control of
VDD APC (s11..) which is statically set at its nominal value.
Original patch link: https://patchwork.kernel.org/project/linux-arm-msm/patch/1595253740-29466-6-git-send-email-loic.poulain@linaro.org/
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[konrad: drop the thermals part, rebase and remove spaces within <>]
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210527194455.782108-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
CoachZ rev3 uses a 100k NTC thermistor for the charger temperatures,
instead of the 47k NTC that is stuffed in earlier revisions. Add .dts
files for rev3.
The 47k NTC currently isn't supported by the PM6150 ADC driver.
Disable the charger thermal zone for rev1 and rev2 to avoid the use
of bogus temperature values.
This also gets rid of the explicit DT files for rev2 and handles
rev2 in the rev1 .dts instead. There was some back and forth
downstream involving the 'dmic_clk_en' pin, after that was sorted
out the DT for rev1 and rev2 is the same.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210322094628.v4.3.I95b8a63103b77cab6a7cf9c150f0541db57fda98@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Konrad Dybcio