commit a282a2f105 upstream.
ceph_frame_desc::fd_lens is an int array. decode_preamble() thus
effectively casts u32 -> int but the checks for segment lengths are
written as if on unsigned values. While reading in HELLO or one of the
AUTH frames (before authentication is completed), arithmetic in
head_onwire_len() can get duped by negative ctrl_len and produce
head_len which is less than CEPH_PREAMBLE_LEN but still positive.
This would lead to a buffer overrun in prepare_read_control() as the
preamble gets copied to the newly allocated buffer of size head_len.
Cc: stable@vger.kernel.org
Fixes: cd1a677cad ("libceph, ceph: implement msgr2.1 protocol (crc and secure modes)")
Reported-by: Thelford Williams <thelford@google.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1995f15590 upstream.
svc_create_memory_pool() is only called from stratix10_svc_drv_probe().
Most of resources in the probe are managed, but not this memremap() call.
There is also no memunmap() call in the file.
So switch to devm_memremap() to avoid a resource leak.
Cc: stable@vger.kernel.org
Fixes: 7ca5ce8965 ("firmware: add Intel Stratix10 service layer driver")
Link: https://lore.kernel.org/all/783e9dfbba34e28505c9efa8bba41f97fd0fa1dc.1686109400.git.christophe.jaillet@wanadoo.fr/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Message-ID: <20230613211521.16366-1-dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 639949a703 upstream.
Since commit 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal
active high") RS485 reception no longer works after a transmission.
The following scenario shows the problem:
1) Open a port in RS485 mode
2) Receive data from remote (OK)
3) Transmit data to remote (OK)
4) Receive data from remote (Nothing received)
In RS485 mode, imx_uart_start_tx() calls imx_uart_stop_rx() and, when the
transmission is complete, imx_uart_stop_tx() calls imx_uart_start_rx().
Since the above commit imx_uart_stop_rx() now sets the loopback bit but
imx_uart_start_rx() does not clear it causing the hardware to remain in
loopback mode and not receive external data.
Fix this by moving the existing loopback disable code to a helper function
and calling it from imx_uart_start_rx() too.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230616104838.2729694-1-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 832e231cff upstream.
When the best clk is searched, we iterate over all possible clk.
If we find a better match, the previous one, if any, needs to be freed.
If a better match has already been found, we still need to free the new
one, otherwise it leaks.
Cc: <stable@vger.kernel.org> # v3.3+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 5f5a7a5578 ("serial: samsung: switch to clkdev based clock lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Message-ID: <cf3e0053d2fc7391b2d906a86cd01a5ef15fb9dc.1686412569.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9c09546e9 upstream.
If clk_get_rate() fails, the clk that has just been allocated needs to be
freed.
Cc: <stable@vger.kernel.org> # v3.3+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 5f5a7a5578 ("serial: samsung: switch to clkdev based clock lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Message-ID: <e4baf6039368f52e5a5453982ddcb9a330fc689e.1686412569.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27a826837e upstream.
The atmel_complete_tx_dma() function disables IRQs at the start
of the function by calling spin_lock_irqsave(&port->lock, flags);
There is no need to disable them a second time using the
spin_lock_irq() function and, in fact, doing so is a bug because
it will enable IRQs prematurely when we call spin_unlock_irq().
Just use spin_lock/unlock() instead without disabling or enabling
IRQs.
Fixes: 08f738be88 ("serial: at91: add tx dma support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/cb7c39a9-c004-4673-92e1-be4e34b85368@moroto.mountain
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a590f03d8d upstream.
If moving the bo to system for swapout failed, we were leaking
a resource. Fix.
Fixes: bfa3357ef9 ("drm/ttm: allocate resource object instead of embedding it v2")
Cc: Christian König <christian.koenig@amd.com>
Cc: "Christian König" <ckoenig.leichtzumerken@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.14+
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230626091450.14757-5-thomas.hellstrom@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a774fe912 upstream.
In restore process worker, pinned BO cause update PTE fail, then
the function re-schedule the restore_work. This will generate dead loop.
Signed-off-by: gaba <gaba@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 613a7956de upstream.
Disable FAMS on a Samsung Odyssey G9 monitor. Experiments show that this
monitor does not work well under some use cases, and is likely
implementation specific bug on the monitor's firmware.
Cc: stable@vger.kernel.org
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 274d205cb5 upstream.
The `DMUB_FW_VERSION` macro has a mistake in that the revision field
is off by one byte. The last byte is typically used for other purposes
and not a revision.
Cc: stable@vger.kernel.org
Cc: Sean Wang <sean.ns.wang@amd.com>
Cc: Marc Rossi <Marc.Rossi@amd.com>
Cc: Hamza Mahfooz <Hamza.Mahfooz@amd.com>
Cc: Tsung-hua (Ryan) Lin <Tsung-hua.Lin@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f48a4b836 upstream.
[Why & How]
We have to check if stream is properly initialized before calling
find_matching_pll(), otherwise we might end up trying to deferecence a
NULL pointer.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Sung-huai Wang <danny.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 072030b178 upstream.
A number of users have reported that there are random hangs occurring
caused by PSR-SU specifically on panels that contain the parade 0803
TCON. Users have been able to work around the issue by disabling PSR
entirely.
To avoid these hangs, disable PSR-SU when this TCON is found.
Cc: stable@vger.kernel.org
Cc: Sean Wang <sean.ns.wang@amd.com>
Cc: Marc Rossi <Marc.Rossi@amd.com>
Cc: Hamza Mahfooz <Hamza.Mahfooz@amd.com>
Suggested-by: Tsung-hua (Ryan) Lin <Tsung-hua.Lin@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2443
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea2c3c0855 upstream.
Per VM BOs must be marked as moved or otherwise their ranges are not
updated on use which might be necessary when the replace operation
splits mappings.
This fixes random GPU hangs when replacing sparse mappings from the
userspace, while OP_MAP/OP_UNMAP works fine because always valid BOs
are correctly handled there.
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26518b3918 upstream.
[Why & How]
Having seamless boot on while forcing debug option ODM combine 2 to 1
will cause some corruptions because of some missing programmings.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Leo Chen <sancchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1966bbfdfe upstream.
[Why]
K1 and K2 not being setting properly when subVP is active.
[How]
Have phantom pipes use the same programing as the main pipes without
checking the paired stream
Cc: stable@vger.kernel.org
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Austin Zheng <austin.zheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a0e005c79 upstream.
[Why] most edp support only timings from edid. applying
non-edid timings, especially those timings out of edp
bandwidth, may damage edp.
[How] do not add non-edid timings for edp.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bdba9d4a3 upstream.
If we disable vblank when entering self-refresh, vblank APIs (like
DRM_IOCTL_WAIT_VBLANK) no longer work. But user space is not aware when
we enter self-refresh, so this appears to be an API violation -- that
DRM_IOCTL_WAIT_VBLANK fails with EINVAL whenever the display is idle and
enters self-refresh.
The downstream driver used by many of these systems never used to
disable vblank for PSR, and in fact, even upstream, we didn't do that
until radically redesigning the state machine in commit 6c836d965b
("drm/rockchip: Use the helpers for PSR").
Thus, it seems like a reasonable API fix to simply restore that
behavior, and leave vblank enabled.
Note that this appears to potentially unbalance the
drm_crtc_vblank_{off,on}() calls in some cases, but:
(a) drm_crtc_vblank_on() documents this as OK and
(b) if I do the naive balancing, I find state machine issues such that
we're not in sync properly; so it's easier to take advantage of (a).
This issue was exposed by IGT's kms_vblank tests, and reported by
KernelCI. The bug has been around a while (longer than KernelCI
noticed), but was only exposed once self-refresh was bugfixed more
recently, and so KernelCI could properly test it. Some other notes in:
https://lore.kernel.org/dri-devel/Y6OCg9BPnJvimQLT@google.com/
Re: renesas/master bisection: igt-kms-rockchip.kms_vblank.pipe-A-wait-forked on rk3399-gru-kevin
== Backporting notes: ==
Marking as 'Fixes' commit 6c836d965b ("drm/rockchip: Use the helpers
for PSR"), but it probably depends on commit bed030a49f
("drm/rockchip: Don't fully disable vop on self refresh") as well.
We also need the previous patch ("drm/atomic: Allow vblank-enabled +
self-refresh "disable""), of course.
v3:
* no update
v2:
* skip unnecessary lock/unlock
Fixes: 6c836d965b ("drm/rockchip: Use the helpers for PSR")
Cc: <stable@vger.kernel.org>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Link: https://lore.kernel.org/dri-devel/Y5itf0+yNIQa6fU4@sirena.org.uk/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230109171809.v3.2.Ic07cba4ab9a7bd3618a9e4258b8f92ea7d10ae5a@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d0e3cac35 upstream.
The self-refresh helper framework overloads "disable" to sometimes mean
"go into self-refresh mode," and this mode activates automatically
(e.g., after some period of unchanging display output). In such cases,
the display pipe is still considered "on", and user-space is not aware
that we went into self-refresh mode. Thus, users may expect that
vblank-related features (such as DRM_IOCTL_WAIT_VBLANK) still work
properly.
However, we trigger the WARN_ONCE() here if a CRTC driver tries to leave
vblank enabled.
Add a different expectation: that CRTCs *should* leave vblank enabled
when going into self-refresh.
This patch is preparation for another patch -- "drm/rockchip: vop: Leave
vblank enabled in self-refresh" -- which resolves conflicts between the
above self-refresh behavior and the API tests in IGT's kms_vblank test
module.
== Some alternatives discussed: ==
It's likely that on many display controllers, vblank interrupts will
turn off when the CRTC is disabled, and so in some cases, self-refresh
may not support vblank. To support such cases, we might consider
additions to the generic helpers such that we fire vblank events based
on a timer.
However, there is currently only one driver using the common
self-refresh helpers (i.e., rockchip), and at least as of commit
bed030a49f ("drm/rockchip: Don't fully disable vop on self refresh"),
the CRTC hardware is powered enough to continue to generate vblank
interrupts.
So we chose the simpler option of leaving vblank interrupts enabled. We
can reevaluate this decision and perhaps augment the helpers if/when we
gain a second driver that has different requirements.
v3:
* include discussion summary
v2:
* add 'ret != 0' warning case for self-refresh
* describe failing test case and relation to drm/rockchip patch better
Cc: <stable@vger.kernel.org> # dependency for "drm/rockchip: vop: Leave
# vblank enabled in self-refresh"
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230109171809.v3.1.I3904f697863649eb1be540ecca147a66e42bfad7@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97f975823f upstream.
Smatch detected a double free path because lpfc_nlp_not_used() releases an
ndlp object before reaching lpfc_nlp_put() at the end of
lpfc_cmpl_els_logo_acc().
Remove the outdated lpfc_nlp_not_used() routine. In
lpfc_mbx_cmpl_ns_reg_login(), replace the call with lpfc_nlp_put(). In
lpfc_cmpl_els_logo_acc(), replace the call with lpfc_unreg_rpi() and keep
the lpfc_nlp_put() at the end of the routine. If ndlp's rpi was
registered, then lpfc_unreg_rpi()'s completion routine performs the final
ndlp clean up after lpfc_nlp_put() is called from lpfc_cmpl_els_logo_acc().
Otherwise if ndlp has no rpi registered, the lpfc_nlp_put() at the end of
lpfc_cmpl_els_logo_acc() is the final ndlp clean up.
Fixes: 4430f7fd09 ("scsi: lpfc: Rework locations of ndlp reference taking")
Cc: <stable@vger.kernel.org> # v5.11+
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/all/Y3OefhyyJNKH%2Fiaf@kili/
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230417191558.83100-3-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57e2c2f2d9 upstream.
When a waiting plock request (F_SETLKW) is sent to userspace
for processing (dlm_controld), the result is returned at a
later time. That result could be incorrectly matched to a
different waiting request in cases where the owner field is
the same (e.g. different threads in a process.) This is fixed
by comparing all the properties in the request and reply.
The results for non-waiting plock requests are now matched
based on list order because the results are returned in the
same order they were sent.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f2b1cb89c upstream.
While a non-waiting posix lock request (F_SETLK) is waiting for
user space processing (in dlm_controld), wait for that processing
to complete with an unkillable wait_event(). This makes F_SETLK
behave the same way for F_RDLCK, F_WRLCK and F_UNLCK. F_SETLKW
continues to use wait_event_killable().
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59e45c758c upstream.
If a posix lock request is waiting for a result from user space
(dlm_controld), do not let it be interrupted unless the process
is killed. This reverts commit a6b1533e9a ("dlm: make posix locks
interruptible"). The problem with the interruptible change is
that all locks were cleared on any signal interrupt. If a signal
was received that did not terminate the process, the process
could continue running after all its dlm posix locks had been
cleared. A future patch will add cancelation to allow proper
interruption.
Cc: stable@vger.kernel.org
Fixes: a6b1533e9a ("dlm: make posix locks interruptible")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c847f4e203 upstream.
Immediately clean up a posix lock request if it is interrupted
while waiting for a result from user space (dlm_controld.) This
largely reverts the recent commit b92a4e3f86 ("fs: dlm: change
posix lock sigint handling"). That previous commit attempted
to defer lock cleanup to the point in time when a result from
user space arrived. The deferred approach was not reliable
because some dlm plock ops may not receive replies.
Cc: stable@vger.kernel.org
Fixes: b92a4e3f86 ("fs: dlm: change posix lock sigint handling")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92655fbda5 upstream.
The GETLK pid values have all been negated since commit 9d5b86ac13
("fs/locks: Remove fl_nspid and use fs-specific l_pid for remote locks").
Revert this for local pids, and leave in place negative pids for remote
owners.
Cc: stable@vger.kernel.org
Fixes: 9d5b86ac13 ("fs/locks: Remove fl_nspid and use fs-specific l_pid for remote locks")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 035641b01e upstream.
Just calling wait_for_device_probe() is not enough to ensure that
asynchronously probed block devices are available (E.G. mmc, usb), so
add a "dm-mod.waitfor=<device1>[,..,<deviceN>]" parameter to get
dm-init to explicitly wait for specific block devices before
initializing the tables with logic similar to the rootwait logic that
was introduced with commit cc1ed7542c ("init: wait for
asynchronously scanned block devices").
E.G. with dm-verity on mmc using:
dm-mod.waitfor="PARTLABEL=hash-a,PARTLABEL=root-a"
[ 0.671671] device-mapper: init: waiting for all devices to be available before creating mapped devices
[ 0.671679] device-mapper: init: waiting for device PARTLABEL=hash-a ...
[ 0.710695] mmc0: new HS200 MMC card at address 0001
[ 0.711158] mmcblk0: mmc0:0001 004GA0 3.69 GiB
[ 0.715954] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
[ 0.722085] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
[ 0.728093] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (249:0)
[ 0.738274] mmcblk0: p1 p2 p3 p4 p5 p6 p7
[ 0.751282] device-mapper: init: waiting for device PARTLABEL=root-a ...
[ 0.751306] device-mapper: init: all devices available
[ 0.751683] device-mapper: verity: sha256 using implementation "sha256-generic"
[ 0.759344] device-mapper: ioctl: dm-0 (vroot) is ready
[ 0.766540] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Cc: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e836007089 upstream.
We've found that using raid0 with the 'original' layout and discard
enabled with different disk sizes (such that at least two zones are
created) can result in data corruption. This is due to the fact that
the discard handling in 'raid0_handle_discard()' assumes the 'alternate'
layout. We've seen this corruption using ext4 but other filesystems are
likely susceptible as well.
More specifically, while multiple zones are necessary to create the
corruption, the corruption may not occur with multiple zones if they
layout in such a way the layout matches what the 'alternate' layout
would have produced. Thus, not all raid0 devices with the 'original'
layout, different size disks and discard enabled will encounter this
corruption.
The 3.14 kernel inadvertently changed the raid0 disk layout for different
size disks. Thus, running a pre-3.14 kernel and post-3.14 kernel on the
same raid0 array could corrupt data. This lead to the creation of the
'original' layout (to match the pre-3.14 layout) and the 'alternate' layout
(to match the post 3.14 layout) in the 5.4 kernel time frame and an option
to tell the kernel which layout to use (since it couldn't be autodetected).
However, when the 'original' layout was added back to 5.4 discard support
for the 'original' layout was not added leading this issue.
I've been able to reliably reproduce the corruption with the following
test case:
1. create raid0 array with different size disks using original layout
2. mkfs
3. mount -o discard
4. create lots of files
5. remove 1/2 the files
6. fstrim -a (or just the mount point for the raid0 array)
7. umount
8. fsck -fn /dev/md0 (spews all sorts of corruptions)
Let's fix this by adding proper discard support to the 'original' layout.
The fix 'maps' the 'original' layout disks to the order in which they are
read/written such that we can compare the disks in the same way that the
current 'alternate' layout does. A 'disk_shift' field is added to
'struct strip_zone'. This could be computed on the fly in
raid0_handle_discard() but by adding this field, we save some computation
in the discard path.
Note we could also potentially fix this by re-ordering the disks in the
zones that follow the first one, and then always read/writing them using
the 'alternate' layout. However, that is seen as a more substantial change,
and we are attempting the least invasive fix at this time to remedy the
corruption.
I've verified the change using the reproducer mentioned above. Typically,
the corruption is seen after less than 3 iterations, while the patch has
run 500+ iterations.
Cc: NeilBrown <neilb@suse.de>
Cc: Song Liu <song@kernel.org>
Fixes: c84a1372df ("md/raid0: avoid RAID0 data corruption due to layout confusion.")
Cc: stable@vger.kernel.org
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230623180523.1901230-1-jbaron@akamai.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d420c9886f upstream.
Add the missing module device table alias to that the driver can be
autoloaded when built as a module.
Cc: stable@vger.kernel.org # 5.14
Fixes: 6b149f3310 ("mfd: pm8008: Add driver for QCOM PM8008 PMIC")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230526091646.17318-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb620ae73b upstream.
The irq_raised completion used to detect the end of a test case is
initialized when the test device is probed, but never reinitialized again
before a test case. As a result, the irq_raised completion synchronization
is effective only for the first ioctl test case executed. Any subsequent
call to wait_for_completion() by another ioctl() call will immediately
return, potentially too early, leading to false positive failures.
Fix this by reinitializing the irq_raised completion before starting a new
ioctl() test command.
Link: https://lore.kernel.org/r/20230415023542.77601-16-dlemoal@kernel.org
Fixes: 2c156ac71c ("misc: Add host side PCI driver for PCI test function device")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f61b7634a3 upstream.
In pci_endpoint_test_remove(), freeing the IRQs after removing the device
creates a small race window for IRQs to be received with the test device
memory already released, causing the IRQ handler to access invalid memory,
resulting in an oops.
Free the device IRQs before removing the device to avoid this issue.
Link: https://lore.kernel.org/r/20230415023542.77601-15-dlemoal@kernel.org
Fixes: e03327122e ("pci_endpoint_test: Add 2 ioctl commands")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e6689b34a upstream.
The address translation unit of the rockchip EP controller does not use
the lower 8 bits of a PCIe-space address to map local memory. Thus we
must set the align feature field to 256 to let the user know about this
constraint.
Link: https://lore.kernel.org/r/20230418074700.1083505-12-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8962b2cb39 upstream.
Previously u16 variables were used to access 32-bit registers, this
resulted in not all of the data being read from the registers. Also
the left shift of more than 16-bits would result in moving data out
of the variable. Use u32 variables to access 32-bit registers
Link: https://lore.kernel.org/r/20230418074700.1083505-10-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 166e89d99d upstream.
Fix legacy IRQ generation for RK3399 PCIe endpoint core according to
the technical reference manual (TRM). Assert and deassert legacy
interrupt (INTx) through the legacy interrupt control register
("PCIE_CLIENT_LEGACY_INT_CTRL") instead of manually generating a PCIe
message. The generation of the legacy interrupt was tested and validated
with the PCIe endpoint test driver.
Link: https://lore.kernel.org/r/20230418074700.1083505-8-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dd3c7c4c8 upstream.
The RK3399 PCIe controller should wait until the PHY PLLs are locked.
Add poll and timeout to wait for PHY PLLs to be locked. If they cannot
be locked generate error message and jump to error handler. Accessing
registers in the PHY clock domain when PLLs are not locked causes hang
The PHY PLLs status is checked through a side channel register.
This is documented in the TRM section 17.5.8.1 "PCIe Initialization
Sequence".
Link: https://lore.kernel.org/r/20230418074700.1083505-5-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f1c42ece1 upstream.
Write PCI Device ID (DID) to the correct register. The Device ID was not
updated through the correct register. Device ID was written to a read-only
register and therefore did not work. The Device ID is now set through the
correct register. This is documented in the RK3399 TRM section 17.6.6.1.1
Link: https://lore.kernel.org/r/20230418074700.1083505-3-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f397fd4ac1 upstream.
Assert PCI Configuration Enable bit after probe. When this bit is left to
0 in the endpoint mode, the RK3399 PCIe endpoint core will generate
configuration request retry status (CRS) messages back to the root complex.
Assert this bit after probe to allow the RK3399 PCIe endpoint core to reply
to configuration requests from the root complex.
This is documented in section 17.5.8.1.2 of the RK3399 TRM.
Link: https://lore.kernel.org/r/20230418074700.1083505-4-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 933f31a2fe upstream.
pci_epf_test_data_transfer() and pci_epf_test_dma_callback() are not
handling DMA transfer completion correctly, leading to completion
notifications to the RC side that are too early. This problem can be
detected when the RC side is running an IOMMU with messages such as:
pci-endpoint-test 0000:0b:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x001c address=0xfff00000 flags=0x0000]
When running the pcitest.sh tests: the address used for a previous
test transfer generates the above error while the next test transfer is
running.
Fix this by testing the DMA transfer status in pci_epf_test_dma_callback()
and notifying the completion only when the transfer status is DMA_COMPLETE
or DMA_ERROR. Furthermore, in pci_epf_test_data_transfer(), be paranoid and
check again the transfer status and always call dmaengine_terminate_sync()
before returning.
Link: https://lore.kernel.org/r/20230415023542.77601-5-dlemoal@kernel.org
Fixes: 8353813c88 ("PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aca56f8ea upstream.
Reinitialize the transfer_complete DMA transfer completion before calling
tx_submit(), to avoid seeing the DMA transfer complete before the
completion is initialized, thus potentially losing the completion
notification.
Link: https://lore.kernel.org/r/20230415023542.77601-4-dlemoal@kernel.org
Fixes: 8353813c88 ("PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a33d700e8e upstream.
In the post init sequence of v2.9.0, write access to read only registers
are not disabled after updating the registers. Fix it by disabling the
access after register update.
Link: https://lore.kernel.org/r/20230619150408.8468-2-manivannan.sadhasivam@linaro.org
Fixes: 5d76117f07 ("PCI: qcom: Add support for IPQ8074 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e54223275b upstream.
When contiguous windows are coalesced by pci_register_host_bridge(), the
second resource is expanded to include the first, and the first is
invalidated and consequently not added to the bus. However, it remains in
the resource hierarchy. For example, these windows:
fec00000-fec7ffff : PCI Bus 0000:00
fec80000-fecbffff : PCI Bus 0000:00
are coalesced into this, where the first resource remains in the tree with
start/end zeroed out:
00000000-00000000 : PCI Bus 0000:00
fec00000-fecbffff : PCI Bus 0000:00
In some cases (e.g. the Xen scratch region), this causes future calls to
allocate_resource() to choose an inappropriate location which the caller
cannot handle.
Fix by releasing the zeroed-out resource and removing it from the resource
hierarchy.
[bhelgaas: commit log]
Fixes: 7c3855c423 ("PCI: Coalesce host bridge contiguous apertures")
Link: https://lore.kernel.org/r/20230525153248.712779-1-ross.lagerwall@citrix.com
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.16+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af40322e90 upstream.
All kind of administrative requests should not been retried. Some card
firmware detects this and assumes a replay attack. This patch checks
on failure if the low level functions indicate a retry (EAGAIN) and
checks for the ADMIN flag set on the request message. If this both
are true, the response code for this message is changed to EIO to make
sure the zcrypt API layer does not attempt to retry the request. As of
now the ADMIN flag is set for a request message when
- for EP11 the field 'flags' of the EP11 CPRB struct has the leftmost
bit set.
- for CCA when the CPRB minor version is 'T3', 'T5', 'T6' or 'T7'.
Please note that the do-not-retry only applies to a request
which has been sent to the card (= has been successfully enqueued) but
the reply indicates some kind of failure and by default it would be
replied. It is totally fine to retry a request if a previous attempt
to enqueue the msg into the firmware queue had some kind of failure
and thus the card has never seen this request.
Reported-by: Frank Uhlig <Frank.Uhlig1@ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f762326b2b upstream.
Copy the sense data to internal driver buffer when the firmware completes
any SCSI I/O command sent through admin queue with sense data for further
use.
Fixes: 506bc1a0d6 ("scsi: mpi3mr: Add support for MPT commands")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20230531184025.3803-1-sumit.saxena@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d50eb4725 upstream.
It was reported that dm-integrity runs out of vmalloc space on 32-bit
architectures. On x86, there is only 128MiB vmalloc space and dm-integrity
consumes it quickly because it has a 64MiB journal and 8MiB recalculate
buffer.
Fix this by reducing the size of the journal to 4MiB and the size of
the recalculate buffer to 1MiB, so that multiple dm-integrity devices
can be created and activated on 32-bit architectures.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d744ae7477 upstream.
Fix the timeout that is used for the initialisation and for the self
test. wait_for_completion_timeout expects a timeout in jiffies, but
RNGC_TIMEOUT is in milliseconds. Call msecs_to_jiffies to do the
conversion.
Cc: stable@vger.kernel.org
Fixes: 1d5449445b ("hwrng: mx-rngc - add a driver for Freescale RNGC")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11509910c5 upstream.
In jfs_dmap.c at line 381, BLKTODMAP is used to get a logical block
number inside dbFree(). db_l2nbperpage, which is the log2 number of
blocks per page, is passed as an argument to BLKTODMAP which uses it
for shifting.
Syzbot reported a shift out-of-bounds crash because db_l2nbperpage is
too big. This happens because the large value is set without any
validation in dbMount() at line 181.
Thus, make sure that db_l2nbperpage is correct while mounting.
Max number of blocks per page = Page size / Min block size
=> log2(Max num_block per page) = log2(Page size / Min block size)
= log2(Page size) - log2(Min block size)
=> Max db_l2nbperpage = L2PSIZE - L2MINBLOCKSIZE
Reported-and-tested-by: syzbot+d2cd27dcf8e04b232eb2@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?id=2a70a453331db32ed491f5cbb07e81bf2d225715
Cc: stable@vger.kernel.org
Suggested-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Siddh Raman Pant <code@siddh.me>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcced95b6b upstream.
PAGE_ALIGN(x) macro gives the next highest value which is multiple of
pagesize. But if x is already page aligned then it simply returns x.
So, if x passed is 0 in dax_zero_range() function, that means the
length gets passed as 0 to ->iomap_begin().
In ext2 it then calls ext2_get_blocks -> max_blocks as 0 and hits bug_on
here in ext2_get_blocks().
BUG_ON(maxblocks == 0);
Instead we should be calling dax_truncate_page() here which takes
care of it. i.e. it only calls dax_zero_range if the offset is not
page/block aligned.
This can be easily triggered with following on fsdax mounted pmem
device.
dd if=/dev/zero of=file count=1 bs=512
truncate -s 0 file
[79.525838] EXT2-fs (pmem0): DAX enabled. Warning: EXPERIMENTAL, use at your own risk
[79.529376] ext2 filesystem being mounted at /mnt1/test supports timestamps until 2038 (0x7fffffff)
[93.793207] ------------[ cut here ]------------
[93.795102] kernel BUG at fs/ext2/inode.c:637!
[93.796904] invalid opcode: 0000 [#1] PREEMPT SMP PTI
[93.798659] CPU: 0 PID: 1192 Comm: truncate Not tainted 6.3.0-rc2-xfstests-00056-g131086faa369 #139
[93.806459] RIP: 0010:ext2_get_blocks.constprop.0+0x524/0x610
<...>
[93.835298] Call Trace:
[93.836253] <TASK>
[93.837103] ? lock_acquire+0xf8/0x110
[93.838479] ? d_lookup+0x69/0xd0
[93.839779] ext2_iomap_begin+0xa7/0x1c0
[93.841154] iomap_iter+0xc7/0x150
[93.842425] dax_zero_range+0x6e/0xa0
[93.843813] ext2_setsize+0x176/0x1b0
[93.845164] ext2_setattr+0x151/0x200
[93.846467] notify_change+0x341/0x4e0
[93.847805] ? lock_acquire+0xf8/0x110
[93.849143] ? do_truncate+0x74/0xe0
[93.850452] ? do_truncate+0x84/0xe0
[93.851739] do_truncate+0x84/0xe0
[93.852974] do_sys_ftruncate+0x2b4/0x2f0
[93.854404] do_syscall_64+0x3f/0x90
[93.855789] entry_SYSCALL_64_after_hwframe+0x72/0xdc
CC: stable@vger.kernel.org
Fixes: 2aa3048e03 ("iomap: switch iomap_zero_range to use iomap_iter")
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <046a58317f29d9603d1068b2bbae47c2332c17ae.1682069716.git.ritesh.list@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcb8898913 upstream.
Commit ebeb20a9cd ("soc: qcom: mdt_loader: Always invoke PAS
mem_setup") dropped the relocate check and made pas_mem_setup run
unconditionally. The code was later moved with commit f4e526ff7e
("soc: qcom: mdt_loader: Extract PAS operations") to
qcom_mdt_pas_init() effectively losing track of what was actually
done.
The assumption that PAS mem_setup can be done anytime was effectively
wrong, with no good reason and this caused regression on some SoC
that use remoteproc to bringup ath11k. One example is IPQ8074 SoC that
effectively broke resulting in remoteproc silently die and ath11k not
working.
On this SoC FW relocate is not enabled and PAS mem_setup was correctly
skipped in previous kernel version resulting in correct bringup and
function of remoteproc and ath11k.
To fix the regression, reintroduce the relocate check in
qcom_mdt_pas_init() and correctly skip PAS mem_setup where relocate is
not enabled.
Fixes: ebeb20a9cd ("soc: qcom: mdt_loader: Always invoke PAS mem_setup")
Tested-by: Robert Marko <robimarko@gmail.com>
Co-developed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230526115511.3328-1-ansuelsmth@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xiubo Li