When bridged ports and standalone ports share a VLAN, e.g. via VLAN
uppers, or untagged traffic with a vlan unaware bridge, the ASIC will
still try to forward traffic to known FDB entries on standalone ports.
But since the port VLAN masks prevent forwarding to bridged ports, this
traffic will be dropped.
This e.g. can be observed in the bridge_vlan_unaware ping tests, where
this breaks pinging with learning on.
Work around this by enabling the simplified EAP mode on switches
supporting it for standalone ports, which causes the ASIC to redirect
traffic of unknown source MAC addresses to the CPU port.
Since standalone ports do not learn, there are no known source MAC
addresses, so effectively this redirects all incoming traffic to the CPU
port.
Fixes: ff39c2d686 ("net: dsa: b53: Add bridge support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20250508091424.26870-1-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Phylink expects MAC drivers to provide LPI callbacks to properly manage
Energy Efficient Ethernet (EEE) configuration. On KSZ switches with
integrated PHYs, LPI is internally handled by hardware, while ports
without integrated PHYs have no documented MAC-level LPI support.
Provide dummy mac_disable_tx_lpi() and mac_enable_tx_lpi() callbacks to
satisfy phylink requirements. Also, set default EEE capabilities during
phylink initialization where applicable.
Since phylink can now gracefully handle optional EEE configuration,
remove the need for the MICREL_NO_EEE PHY flag.
This change addresses issues caused by incomplete EEE refactoring
introduced in commit fe0d4fd928 ("net: phy: Keep track of EEE
configuration"). It is not easily possible to fix all older kernels, but
this patch ensures proper behavior on latest kernels and can be
considered for backporting to stable kernels starting from v6.14.
Fixes: fe0d4fd928 ("net: phy: Keep track of EEE configuration")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # v6.14+
Link: https://patch.msgid.link/20250504081434.424489-2-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
b53 supported switches support configuring ageing time between 1 and
1,048,575 seconds, so add an appropriate setter.
This allows b53 to pass the FDB learning test for both vlan aware and
vlan unaware bridges.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250510092211.276541-1-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It has been reported that when under a bridge with stp_state=1, the logs
get spammed with this message:
[ 251.734607] fsl_dpaa2_eth dpni.5 eth0: Couldn't decode source port
Further debugging shows the following info associated with packets:
source_port=-1, switch_id=-1, vid=-1, vbid=1
In other words, they are data plane packets which are supposed to be
decoded by dsa_tag_8021q_find_port_by_vbid(), but the latter (correctly)
refuses to do so, because no switch port is currently in
BR_STATE_LEARNING or BR_STATE_FORWARDING - so the packet is effectively
unexpected.
The error goes away after the port progresses to BR_STATE_LEARNING in 15
seconds (the default forward_time of the bridge), because then,
dsa_tag_8021q_find_port_by_vbid() can correctly associate the data plane
packets with a plausible bridge port in a plausible STP state.
Re-reading IEEE 802.1D-1990, I see the following:
"4.4.2 Learning: (...) The Forwarding Process shall discard received
frames."
IEEE 802.1D-2004 further clarifies:
"DISABLED, BLOCKING, LISTENING, and BROKEN all correspond to the
DISCARDING port state. While those dot1dStpPortStates serve to
distinguish reasons for discarding frames, the operation of the
Forwarding and Learning processes is the same for all of them. (...)
LISTENING represents a port that the spanning tree algorithm has
selected to be part of the active topology (computing a Root Port or
Designated Port role) but is temporarily discarding frames to guard
against loops or incorrect learning."
Well, this is not what the driver does - instead it sets
mac[port].ingress = true.
To get rid of the log spam, prevent unexpected data plane packets to
be received by software by discarding them on ingress in the LISTENING
state.
In terms of blame attribution: the prints only date back to commit
d7f9787a76 ("net: dsa: tag_8021q: add support for imprecise RX based
on the VBID"). However, the settings would permit a LISTENING port to
forward to a FORWARDING port, and the standard suggests that's not OK.
Fixes: 640f763f98 ("net: dsa: sja1105: Add support for Spanning Tree Protocol")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250509113816.2221992-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
New timestamping API was introduced in commit 66f7223039 ("net: add
NDOs for configuring hardware timestamping") from kernel v6.6. It is
time to convert DSA to the new API, so that the ndo_eth_ioctl() path can
be removed completely.
Move the ds->ops->port_hwtstamp_get() and ds->ops->port_hwtstamp_set()
calls from dsa_user_ioctl() to dsa_user_hwtstamp_get() and
dsa_user_hwtstamp_set().
Due to the fact that the underlying ifreq type changes to
kernel_hwtstamp_config, the drivers and the Ocelot switchdev front-end,
all hooked up directly or indirectly, must also be converted all at once.
The conversion also updates the comment from dsa_port_supports_hwtstamp(),
which is no longer true because kernel_hwtstamp_config is kernel memory
and does not need copy_to_user(). I've deliberated whether it is
necessary to also update "err != -EOPNOTSUPP" to a more general "!err",
but all drivers now either return 0 or -EOPNOTSUPP.
The existing logic from the ocelot_ioctl() function, to avoid
configuring timestamping if the PHY supports the operation, is obsoleted
by more advanced core logic in dev_set_hwtstamp_phylib().
This is only a partial preparation for proper PHY timestamping support.
None of these switch driver currently sets up PTP traps for PHY
timestamping, so setting dev->see_all_hwtstamp_requests is not yet
necessary and the conversion is relatively trivial.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # felix, sja1105, mv88e6xxx
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250508095236.887789-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a port gets set up, b53 disables learning and enables the port for
flooding. This can undo any bridge configuration on the port.
E.g. the following flow would disable learning on a port:
$ ip link add br0 type bridge
$ ip link set sw1p1 master br0 <- enables learning for sw1p1
$ ip link set br0 up
$ ip link set sw1p1 up <- disables learning again
Fix this by populating dsa_switch_ops::port_setup(), and set up initial
config there.
Fixes: f9b3827ee6 ("net: dsa: b53: Support setting learning on port")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-12-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When VLAN filtering is off, we configure the switch to forward, but not
learn on VLAN table misses. This effectively disables learning while not
filtering.
Fix this by switching to forward and learn. Setting the learning disable
register will still control whether learning actually happens.
Fixes: dad8d7c645 ("net: dsa: b53: Properly account for VLAN filtering")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-11-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To allow runtime switching between vlan aware and vlan non-aware mode,
we need to properly keep track of any bridge VLAN configuration.
Likewise, we need to know when we actually switch between both modes, to
not have to rewrite the full VLAN table every time we update the VLANs.
So keep track of the current vlan_filtering mode, and on changes, apply
the appropriate VLAN configuration.
Fixes: 0ee2af4ebb ("net: dsa: set configure_vlan_while_not_filtering to true by default")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-10-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Documentation/networking/switchdev.rst says:
- with VLAN filtering turned off: the bridge is strictly VLAN unaware and its
data path will process all Ethernet frames as if they are VLAN-untagged.
The bridge VLAN database can still be modified, but the modifications should
have no effect while VLAN filtering is turned off.
This breaks if we immediately apply the VLAN configuration, so skip
writing it when vlan_filtering is off.
Fixes: 0ee2af4ebb ("net: dsa: set configure_vlan_while_not_filtering to true by default")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-9-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since we cannot set forwarding destinations per VLAN, we should not have
a VLAN 0 configured, as it would allow untagged traffic to work across
ports on VLAN aware bridges regardless if a PVID untagged VLAN exists.
So remove the VLAN 0 on join, an re-add it on leave. But only do so if
we have a VLAN aware bridge, as without it, untagged traffic would
become tagged with VID 0 on a VLAN unaware bridge.
Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-8-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While JOIN_ALL_VLAN allows to join all VLANs, we still need to keep the
default VLAN enabled so that untagged traffic stays untagged.
So rejoin the default VLAN even for switches with JOIN_ALL_VLAN support.
Fixes: 48aea33a77 ("net: dsa: b53: Add JOIN_ALL_VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-7-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The untagged default VLAN is added to the default vlan, which may be
one, but we modify the VLAN 0 entry on bridge leave.
Fix this to use the correct VLAN entry for the default pvid.
Fixes: fea8335317 ("net: dsa: b53: Fix default VLAN ID")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-6-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Presumably the intention here was to flush the VLAN of the old pvid, not
the added VLAN again, which we already flushed before.
Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-5-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the PVID of ports are only set when adding/updating VLANs with
PVID set or removing VLANs, but not when clearing the PVID flag of a
VLAN.
E.g. the following flow
$ ip link add br0 type bridge vlan_filtering 1
$ ip link set sw1p1 master bridge
$ bridge vlan add dev sw1p1 vid 10 pvid untagged
$ bridge vlan add dev sw1p1 vid 10 untagged
Would keep the PVID set as 10, despite the flag being cleared. Fix this
by checking if we need to unset the PVID on vlan updates.
Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-4-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Broadcom management header does not carry the original VLAN tag
state information, just the ingress port, so for untagged frames we do
not know from which VLAN they originated.
Therefore keep the CPU port always tagged except for VLAN 0.
Fixes the following setup:
$ ip link add br0 type bridge vlan_filtering 1
$ ip link set sw1p1 master br0
$ bridge vlan add dev br0 pvid untagged self
$ ip link add sw1p2.10 link sw1p2 type vlan id 10
Where VID 10 would stay untagged on the CPU port.
Fixes: 2c32a3d3c2 ("net: dsa: b53: Do not force CPU to be always tagged")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-3-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow reserved multicast to ignore VLAN membership so STP and other
management protocols work without a PVID VLAN configured when using a
vlan aware bridge.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-2-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simplest setup to reproduce the issue: connect 2 ports of the
LS1028A-RDB together (eno0 with swp0) and run:
$ ip link set eno0 up && ip link set swp0 up
$ tc qdisc replace dev swp0 parent root handle 100 taprio num_tc 8 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 map 0 1 2 3 4 5 6 7 \
base-time 0 sched-entry S 20 300000 sched-entry S 10 200000 \
sched-entry S 20 300000 sched-entry S 48 200000 \
sched-entry S 20 300000 sched-entry S 83 200000 \
sched-entry S 40 300000 sched-entry S 00 200000 flags 2
$ ptp4l -i eno0 -f /etc/linuxptp/configs/gPTP.cfg -m &
$ ptp4l -i swp0 -f /etc/linuxptp/configs/gPTP.cfg -m
One will observe that the PTP state machine on swp0 starts
synchronizing, then it attempts to do a clock step, and after that, it
never fails to recover from the condition below.
ptp4l[82.427]: selected best master clock 00049f.fffe.05f627
ptp4l[82.428]: port 1 (swp0): MASTER to UNCALIBRATED on RS_SLAVE
ptp4l[83.252]: port 1 (swp0): UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[83.886]: rms 4537731277 max 9075462553 freq -18518 +/- 11467 delay 818 +/- 0
ptp4l[84.170]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[85.304]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[85.305]: port 1 (swp0): send peer delay response failed
ptp4l[85.306]: port 1 (swp0): clearing fault immediately
ptp4l[86.304]: timed out while polling for tx timestamp
A hint is given by the non-zero statistics for dropped packets which
were expecting hardware TX timestamps:
$ ethtool --include-statistics -T swp0
(...)
Statistics:
tx_pkts: 30
tx_lost: 11
tx_err: 0
We know that when PTP clock stepping takes place (from ocelot_ptp_settime64()
or from ocelot_ptp_adjtime()), vsc9959_tas_clock_adjust() is called.
Another interesting hint is that placing an early return in
vsc9959_tas_clock_adjust(), so as to neutralize this function, fixes the
issue and TX timestamps are no longer dropped.
The debugging function written by me and included below is intended to
read the GCL RAM, after the admin schedule became operational, through
the two status registers available for this purpose:
QSYS_GCL_STATUS_REG_1 and QSYS_GCL_STATUS_REG_2.
static void vsc9959_print_tas_gcl(struct ocelot *ocelot)
{
u32 val, list_length, interval, gate_state;
int i, err;
err = read_poll_timeout(ocelot_read, val,
!(val & QSYS_PARAM_STATUS_REG_8_CONFIG_PENDING),
10, 100000, false, ocelot, QSYS_PARAM_STATUS_REG_8);
if (err) {
dev_err(ocelot->dev,
"Failed to wait for TAS config pending bit to clear: %pe\n",
ERR_PTR(err));
return;
}
val = ocelot_read(ocelot, QSYS_PARAM_STATUS_REG_3);
list_length = QSYS_PARAM_STATUS_REG_3_LIST_LENGTH_X(val);
dev_info(ocelot->dev, "GCL length: %u\n", list_length);
for (i = 0; i < list_length; i++) {
ocelot_rmw(ocelot,
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM(i),
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM_M,
QSYS_GCL_STATUS_REG_1);
interval = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_2);
val = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_1);
gate_state = QSYS_GCL_STATUS_REG_1_GATE_STATE_X(val);
dev_info(ocelot->dev, "GCL entry %d: states 0x%x interval %u\n",
i, gate_state, interval);
}
}
Calling it from two places: after the initial QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
performed by vsc9959_qos_port_tas_set(), and after the one done by
vsc9959_tas_clock_adjust(), I notice the following difference.
From the tc-taprio process context, where the schedule was initially
configured, the GCL looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 1: states 0x10 interval 200000
mscc_felix 0000:00:00.5: GCL entry 2: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 3: states 0x48 interval 200000
mscc_felix 0000:00:00.5: GCL entry 4: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 5: states 0x83 interval 200000
mscc_felix 0000:00:00.5: GCL entry 6: states 0x40 interval 300000
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 200000
But from the ptp4l clock stepping process context, when the
vsc9959_tas_clock_adjust() hook is called, the GCL RAM of the
operational schedule now looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 1: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 2: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 3: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 4: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 5: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 6: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 0
I do not have a formal explanation, just experimental conclusions.
It appears that after triggering QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
for a port's TAS, the GCL entry RAM is updated anyway, despite what the
documentation claims: "Specify the time interval in
QSYS::GCL_CFG_REG_2.TIME_INTERVAL. This triggers the actual RAM
write with the gate state and the time interval for the entry number
specified". We don't touch that register (through vsc9959_tas_gcl_set())
from vsc9959_tas_clock_adjust(), yet the GCL RAM is updated anyway.
It seems to be updated with effectively stale memory, which in my
testing can hold a variety of things, including even pieces of the
previously applied schedule, for particular schedule lengths.
As such, in most circumstances it is very difficult to pinpoint this
issue, because the newly updated schedule would "behave strangely",
but ultimately might still pass traffic to some extent, due to some
gate entries still being present in the stale GCL entry RAM. It is easy
to miss.
With the particular schedule given at the beginning, the GCL RAM
"happens" to be reproducibly rewritten with all zeroes, and this is
consistent with what we see: when the time-aware shaper has gate entries
with all gates closed, traffic is dropped on TX, no wonder we can't
retrieve TX timestamps.
Rewriting the GCL entry RAM when reapplying the new base time fixes the
observed issue.
Fixes: 8670dc33f4 ("net: dsa: felix: update base time of time-aware shaper when adjusting PTP time")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.15-rc4).
This pull includes wireless and a fix to vxlan which isn't
in Linus's tree just yet. The latter creates with a silent conflict
/ build breakage, so merging it now to avoid causing problems.
drivers/net/vxlan/vxlan_vnifilter.c
094adad913 ("vxlan: Use a single lock to protect the FDB table")
087a9eb9e5 ("vxlan: vnifilter: Fix unlocked deletion of default FDB entry")
https://lore.kernel.org/20250423145131.513029-1-idosch@nvidia.com
No "normal" conflicts, or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MT7531 standalone and MMIO variants found in MT7988 and EN7581 share
most basic properties. Despite that, assisted_learning_on_cpu_port and
mtu_enforcement_ingress were only applied for MT7531 but not for MT7988
or EN7581, causing the expected issues on MMIO devices.
Apply both settings equally also for MT7988 and EN7581 by moving both
assignments form mt7531_setup() to mt7531_setup_common().
This fixes unwanted flooding of packets due to unknown unicast
during DA lookup, as well as issues with heterogenous MTU settings.
Fixes: 7f54cc9772 ("net: dsa: mt7530: split-off common parts from mt7531_setup")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/89ed7ec6d4fa0395ac53ad2809742bb1ce61ed12.1745290867.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Don't populate the read-only array offsets on the stack at run time,
instead make it static const.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://patch.msgid.link/20250417161353.490219-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King reports that on the ZII dev rev B, deleting a bridge VLAN
from a user port fails with -ENOENT:
https://lore.kernel.org/netdev/Z_lQXNP0s5-IiJzd@shell.armlinux.org.uk/
This comes from mv88e6xxx_port_vlan_leave() -> mv88e6xxx_mst_put(),
which tries to find an MST entry in &chip->msts associated with the SID,
but fails and returns -ENOENT as such.
But we know that this chip does not support MST at all, so that is not
surprising. The question is why does the guard in mv88e6xxx_mst_put()
not exit early:
if (!sid)
return 0;
And the answer seems to be simple: the sid comes from vlan.sid which
supposedly was previously populated by mv88e6xxx_vtu_get().
But some chip->info->ops->vtu_getnext() implementations do not populate
vlan.sid, for example see mv88e6185_g1_vtu_getnext(). In that case,
later in mv88e6xxx_port_vlan_leave() we are using a garbage sid which is
just residual stack memory.
Testing for sid == 0 covers all cases of a non-bridge VLAN or a bridge
VLAN mapped to the default MSTI. For some chips, SID 0 is valid and
installed by mv88e6xxx_stu_setup(). A chip which does not support the
STU would implicitly only support mapping all VLANs to the default MSTI,
so although SID 0 is not valid, it would be sufficient, if we were to
zero-initialize the vlan structure, to fix the bug, due to the
coincidence that a test for vlan.sid == 0 already exists and leads to
the same (correct) behavior.
Another option which would be sufficient would be to add a test for
mv88e6xxx_has_stu() inside mv88e6xxx_mst_put(), symmetric to the one
which already exists in mv88e6xxx_mst_get(). But that placement means
the caller will have to dereference vlan.sid, which means it will access
uninitialized memory, which is not nice even if it ignores it later.
So we end up making both modifications, in order to not rely just on the
sid == 0 coincidence, but also to avoid having uninitialized structure
fields which might get temporarily accessed.
Fixes: acaf4d2e36 ("net: dsa: mv88e6xxx: MST Offloading")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250414212913.2955253-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King reports that a system with mv88e6xxx dereferences a NULL
pointer when unbinding this driver:
https://lore.kernel.org/netdev/Z_lRkMlTJ1KQ0kVX@shell.armlinux.org.uk/
The crash seems to be in devlink_region_destroy(), which is not NULL
tolerant but is given a NULL devlink global region pointer.
At least on some chips, some devlink regions are conditionally registered
since the blamed commit, see mv88e6xxx_setup_devlink_regions_global():
if (cond && !cond(chip))
continue;
These are MV88E6XXX_REGION_STU and MV88E6XXX_REGION_PVT. If the chip
does not have an STU or PVT, it should crash like this.
To fix the issue, avoid unregistering those regions which are NULL, i.e.
were skipped at mv88e6xxx_setup_devlink_regions_global() time.
Fixes: 836021a2d0 ("net: dsa: mv88e6xxx: Export cross-chip PVT as devlink region")
Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250414212850.2953957-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For STP to work, receiving BPDUs is essential, but the appropriate bit
was never set. Without GC_RX_BPDU_EN, the switch chip will filter all
BPDUs, even if an appropriate PVID VLAN was setup.
Fixes: ff39c2d686 ("net: dsa: b53: Add bridge support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20250414200434.194422-1-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PTP_PEROUT_REQUEST2 ioctl has gained support for flags specifying
specific output behavior including PTP_PEROUT_ONE_SHOT,
PTP_PEROUT_DUTY_CYCLE, PTP_PEROUT_PHASE.
Driver authors are notorious for not checking the flags of the request.
This results in misinterpreting the request, generating an output signal
that does not match the requested value. It is anticipated that even more
flags will be added in the future, resulting in even more broken requests.
Expecting these issues to be caught during review or playing whack-a-mole
after the fact is not a great solution.
Instead, introduce the supported_perout_flags field in the ptp_clock_info
structure. Update the core character device logic to explicitly reject any
request which has a flag not on this list.
This ensures that drivers must 'opt in' to the flags they support. Drivers
which don't set the .supported_perout_flags field will not need to check
that unsupported flags aren't passed, as the core takes care of this.
Update the drivers which do support flags to set this new field.
Note the following driver files set n_per_out to a non-zero value but did
not check the flags at all:
• drivers/ptp/ptp_clockmatrix.c
• drivers/ptp/ptp_idt82p33.c
• drivers/ptp/ptp_fc3.c
• drivers/net/ethernet/ti/am65-cpts.c
• drivers/net/ethernet/aquantia/atlantic/aq_ptp.c
• drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c
• drivers/net/dsa/sja1105/sja1105_ptp.c
• drivers/net/ethernet/freescale/dpaa2/dpaa2-ptp.c
• drivers/net/ethernet/mscc/ocelot_vsc7514.c
• drivers/net/ethernet/intel/i40e/i40e_ptp.c
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250414-jk-supported-perout-flags-v2-2-f6b17d15475c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PTP_EXTTS_REQUEST(2) ioctl has a flags field which specifies how the
external timestamp request should behave. This includes which edge of the
signal to timestamp, as well as a specialized "offset" mode. It is expected
that more flags will be added in the future.
Driver authors routinely do not check the flags, often accepting requests
with flags which they do not support. Even drivers which do check flags may
not be future-proofed to reject flags not yet defined. Thus, any future
flag additions often require manually updating drivers to reject these
flags.
This approach of hoping we catch flag checks during review, or playing
whack-a-mole after the fact is the wrong approach.
Introduce the "supported_extts_flags" field to the ptp_clock_info
structure. This field defines the set of flags the device actually
supports.
Update the core character device logic to check this field and reject
unsupported requests. Getting this right is somewhat tricky. First, to
avoid unnecessary repetition and make basic functionality work when
.supported_extts_flags is 0, the core always accepts the PTP_ENABLE_FEATURE
flag. This flag is used to set the 'on' parameter to the .enable function
and is thus always 'supported' by all drivers.
For backwards compatibility, the PTP_RISING_EDGE and PTP_FALLING_EDGE flags
are merely "hints" when using the old PTP_EXTTS_REQUEST ioctl, and are not
expected to be enforced. If the user issues PTP_EXTTS_REQUEST2, the
PTP_STRICT_FLAGS flag is added which is supposed to inform the driver to
strictly validate the flags and reject unsupported requests. To handle
this, first check if the driver reports PTP_STRICT_FLAGS support. If it
does not, then always allow the PTP_RISING_EDGE and PTP_FALLING_EDGE flags.
This keeps backwards compatibility with the original PTP_EXTTS_REQUEST
ioctl where these flags are not guaranteed to be honored.
This way, drivers which do not set the supported_extts_flags will continue
to accept requests for the original PTP_EXTTS_REQUEST ioctl. The core will
automatically reject requests with new flags, and correctly reject requests
with PTP_STRICT_FLAGS, where the driver is supposed to strictly validate
the flags.
Update the various drivers, refactoring their validation logic into the
.supported_extts_flags field. For consistency and readability,
PTP_ENABLE_FEATURE is not set in the supported flags list, and
PTP_EXTTS_EDGES is expanded to PTP_RISING_EDGE | PTP_FALLING_EDGE in all
cases.
Note the following driver files set n_ext_ts to a non-zero value but did
not check flags at all:
• drivers/net/ethernet/freescale/dpaa2/dpaa2-ptp.c
• drivers/net/ethernet/freescale/enetc/enetc_ptp.c
• drivers/net/ethernet/intel/i40e/i40e_ptp.c
• drivers/net/ethernet/marvell/octeontx2/nic/otx2_ptp.c
• drivers/net/ethernet/renesas/ravb_ptp.c
• drivers/net/ethernet/renesas/rtsn.c
• drivers/net/ethernet/renesas/rtsn.h
• drivers/net/ethernet/ti/am65-cpts.c
• drivers/net/ethernet/ti/cpts.h
• drivers/net/ethernet/ti/icssg/icss_iep.c
• drivers/net/ethernet/xscale/ptp_ixp46x.c
• drivers/net/phy/bcm-phy-ptp.c
• drivers/ptp/ptp_ocp.c
• drivers/ptp/ptp_pch.c
• drivers/ptp/ptp_qoriq.c
These drivers behavior does change slightly: they will now reject the
PTP_EXTTS_REQUEST2 ioctl, because they do not strictly validate their
flags. This also makes them no longer incorrectly accept PTP_EXT_OFFSET.
Also note that the renesas ravb driver does not support PTP_STRICT_FLAGS.
We could leave the .supported_extts_flags as 0, but I added the
PTP_RISING_EDGE | PTP_FALLING_EDGE since the driver previously manually
validated these flags. This is equivalent to 0 because the core will allow
these flags regardless unless PTP_STRICT_FLAGS is also set.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250414-jk-supported-perout-flags-v2-1-f6b17d15475c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It was reported that the internally calculated counter might differ from
the real one from the Switch MIB. This can happen if the switch directly
forward packets between the ports or offload small packets like ARP
request. In such case, the kernel counter will desync compared to the
real one transmitted and received by the Switch.
To correctly provide the real info to the kernel, implement .get_stats64
that will directly read the current MIB counter from the switch
register.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-7-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For consistency with the other MIB counter, move also the remaining MIB
counter to define and update the custom MIB table.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-6-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drop custom handling of TX/RX packet stats and error MIB counter and handle
them in the standard .get_eth_mac_stats API
The MIB entry are dropped from the custom MIB table and converted to
a define providing only the MIB offset.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-5-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drop custom handling of TX/RX pause frame MIB counter and handle
them in the standard .get_eth_ctrl_stats API
The MIB entry are dropped from the custom MIB table and converted to
a define providing only the MIB offset.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-4-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drop custom handling of packet size and RX error MIB counter and handle
them in the standard .get_rmon_stats API
The MIB entry are dropped from the custom MIB table and converted to
a define providing only the MIB offset.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-3-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In preparation for migration to use of standard MIB API, generalize the
read port stats logic to a dedicated function.
This will permit to manually provide the offset and size of the MIB
counter to directly access specific counter.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250410163022.3695-2-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Implement Enhanced Transmission Selection scheduler (ETS) support for
KSZ88x3 devices, which support two fixed egress scheduling modes:
Strict Priority and Weighted Fair Queuing (WFQ).
Since the switch does not allow remapping priorities to queues or
adjusting weights, this implementation only supports enabling
strict priority mode. If strict mode is not explicitly requested,
the switch falls back to its default WFQ mode.
This patch introduces KSZ88x3-specific handlers for ETS add and
delete operations and uses TXQ Split Control registers to toggle
the WFQ enable bit per queue. Corresponding macros are also added
for register access.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250410124249.2728568-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The mv88e6xxx has an internal PPU that polls PHY state. If we want to
access the internal PHYs, we need to disable the PPU first. Because
that is a slow operation, a 10ms timer is used to re-enable it,
canceled with every access, so bulk operations effectively only
disable it once and re-enable it some 10ms after the last access.
If a PHY is accessed and then the mv88e6xxx module is removed before
the 10ms are up, the PPU re-enable ends up accessing a dangling pointer.
This especially affects probing during bootup. The MDIO bus and PHY
registration may succeed, but registration with the DSA framework
may fail later on (e.g. because the CPU port depends on another,
very slow device that isn't done probing yet, returning -EPROBE_DEFER).
In this case, probe() fails, but the MDIO subsystem may already have
accessed the MIDO bus or PHYs, arming the timer.
This is fixed as follows:
- If probe fails after mv88e6xxx_phy_init(), make sure we also call
mv88e6xxx_phy_destroy() before returning
- In mv88e6xxx_remove(), make sure we do the teardown in the correct
order, calling mv88e6xxx_phy_destroy() after unregistering the
switch device.
- In mv88e6xxx_phy_destroy(), destroy both the timer and the work item
that the timer might schedule, synchronously waiting in case one of
the callbacks already fired and destroying the timer first, before
waiting for the work item.
- Access to the PPU is guarded by a mutex, the worker acquires it
with a mutex_trylock(), not proceeding with the expensive shutdown
if that fails. We grab the mutex in mv88e6xxx_phy_destroy() to make
sure the slow PPU shutdown is already done or won't even enter, when
we wait for the work item.
Fixes: 2e5f032095 ("dsa: add support for the Marvell 88E6131 switch chip")
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20250401135705.92760-1-david.oberhollenzer@sigma-star.at
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge in late fixes to prepare for the 6.15 net-next PR.
No conflicts, adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
919f9f497d ("eth: bnxt: fix out-of-range access of vnic_info array")
fe96d717d3 ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove KSZ88x3-specific priority and apptrust configuration logic that was
based on incorrect register access assumptions. Also fix the register
offset for KSZ8_REG_PORT_1_CTRL_0 to align with get_port_addr() logic.
The KSZ88x3 switch family uses a different register layout compared to
KSZ9477-compatible variants. Specifically, port control registers need
offset adjustment through get_port_addr(), and do not match the datasheet
values directly.
Commit a1ea57710c ("net: dsa: microchip: dcb: add special handling for
KSZ88X3 family") introduced quirks based on datasheet offsets, which do
not work with the driver's internal addressing model. As a result, these
quirks addressed the wrong ports and caused unstable behavior.
This patch removes all KSZ88x3-specific DCB quirks and corrects the port
control register offset, effectively restoring working and predictable
apptrust configuration.
Fixes: a1ea57710c ("net: dsa: microchip: dcb: add special handling for KSZ88X3 family")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250321141044.2128973-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are actually 2 problems:
- deleting the last element doesn't require the memmove of elements
[i + 1, end) over it. Actually, element i+1 is out of bounds.
- The memmove itself should move size - i - 1 elements, because the last
element is out of bounds.
The out-of-bounds element still remains out of bounds after being
accessed, so the problem is only that we touch it, not that it becomes
in active use. But I suppose it can lead to issues if the out-of-bounds
element is part of an unmapped page.
Fixes: 6666cebc5e ("net: dsa: sja1105: Add support for VLAN operations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318115716.2124395-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is all that we can support timestamping, so we shouldn't accept
anything else. Also see sja1105_hwtstamp_get().
To avoid erroring out in an inconsistent state, operate on copies of
priv->hwts_rx_en and priv->hwts_tx_en, and write them back when nothing
else can fail anymore.
Fixes: a602afd200 ("net: dsa: sja1105: Expose PTP timestamping ioctls to userspace")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318115716.2124395-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Port counters with no name (aka
sja1105_port_counters[__SJA1105_COUNTER_UNUSED]) are skipped when
reporting sja1105_get_sset_count(), but are not skipped during
sja1105_get_strings() and sja1105_get_ethtool_stats().
As a consequence, the first reported counter has an empty name and a
bogus value (reads from area 0, aka MAC, from offset 0, bits start:end
0:0). Also, the last counter (N_NOT_REACH on E/T, N_RX_BCAST on P/Q/R/S)
gets pushed out of the statistics counters that get shown.
Skip __SJA1105_COUNTER_UNUSED consistently, so that the bogus counter
with an empty name disappears, and in its place appears a valid counter.
Fixes: 039b167d68 ("net: dsa: sja1105: don't use burst SPI reads for port statistics")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250318115716.2124395-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the workaround for erratum
3.3 RGMII timing may be out of spec when transmit delay is enabled
for the 6320 family, which says:
When transmit delay is enabled via Port register 1 bit 14 = 1, duty
cycle may be out of spec. Under very rare conditions this may cause
the attached device receive CRC errors.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: <stable@vger.kernel.org> # 5.4.x
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-8-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix internal PHYs definition for the 6320 family, which has only 2
internal PHYs (on ports 3 and 4).
Fixes: bc3931557d ("net: dsa: mv88e6xxx: Add number of internal PHYs")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: <stable@vger.kernel.org> # 6.6.x
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-7-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit c050f5e91b ("net: dsa: mv88e6xxx: Fill in STU support for all
supported chips") introduced STU methods, but did not add them to the
6320 family. Fix it.
Fixes: c050f5e91b ("net: dsa: mv88e6xxx: Fill in STU support for all supported chips")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-6-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit f3a2cd326e ("net: dsa: mv88e6xxx: introduce .port_set_policy")
did not add the .port_set_policy() method for the 6320 family. Fix it.
Fixes: f3a2cd326e ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-5-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit f364565221 ("net: dsa: mv88e6xxx: move PVT description in
info") did not enable PVT for 6321 switch. Fix it.
Fixes: f364565221 ("net: dsa: mv88e6xxx: move PVT description in info")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-4-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The atu_move_port_mask for 6341 family (Topaz) is 0xf, not 0x1f. The
PortVec field is 8 bits wide, not 11 as in 6390 family. Fix this.
Fixes: e606ca36bb ("net: dsa: mv88e6xxx: rework ATU Remove")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-3-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VTU registers of the 6320 family use the 6352 semantics, not 6185.
Fix it.
Fixes: b8fee95710 ("net: dsa: mv88e6xxx: add VLAN Get Next support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: <stable@vger.kernel.org> # 5.15.x
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-2-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py
75cc19c8ff ("selftests: drv-net: add xdp cases for ping.py")
de94e86974 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c
a70f891e0f ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()")
1d22d3060b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile
6f50175cca ("selftests: Add IPv6 link-local address generation tests for GRE devices.")
2e5584e0f9 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c
661958552e ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
fe96d717d3 ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ATU Load operations could fail silently if there's not enough space
on the device to hold the new entry. When this happens, the symptom
depends on the unknown flood settings. If unknown multicast flood is
disabled, the multicast packets are dropped when the ATU table is
full. If unknown multicast flood is enabled, the multicast packets
will be flooded to all ports. Either way, IGMP snooping is broken
when the ATU Load operation fails silently.
Do a Read-After-Write verification after each fdb/mdb add operation
to make sure that the operation was really successful, and return
-ENOSPC otherwise.
Fixes: defb05b9b9 ("net: dsa: mv88e6xxx: Add support for fdb_add, fdb_del, and fdb_getnext")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250306172306.3859214-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
net/ethtool/cabletest.c
2bcf4772e4 ("net: ethtool: try to protect all callback with netdev instance lock")
637399bf7e ("net: ethtool: netlink: Allow NULL nlattrs when getting a phy_device")
No Adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On MMIO devices (e.g. MT7988 or EN7581) unicast traffic received on lanX
port is flooded on all other user ports if the DSA switch is configured
without VLAN support since PORT_MATRIX in PCR regs contains all user
ports. Similar to MDIO devices (e.g. MT7530 and MT7531) fix the issue
defining default VLAN-ID 0 for MT7530 MMIO devices.
Fixes: 110c18bfed ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/20250304-mt7988-flooding-fix-v1-1-905523ae83e9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the custom IRQ chip handler and mask/unmask functions with
REGMAP_IRQ. This significantly simplifies the code and allows for the
removal of almost all interrupt-related functions from mt7530.c.
Tested on MT7988A built-in switch (MMIO) as well as MT7531AE IC (MDIO).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/221013c3530b61504599e285c341a993f6188f00.1740792674.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Packet Processor Engine (PPE) module used for hw acceleration on EN7581
mac block, in order to properly parse packets, requires DSA untagged
packets on TX side and read DSA tag from DMA descriptor on RX side.
For this reason, enable RX Special Tag (SPTAG) for EN7581 SoC.
This is a preliminary patch to enable netfilter flowtable hw offloading
on EN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make NET_DSA_REALTEK_RTL8366RB_LEDS a hidden symbol.
It seems very unlikely user would want to intentionally
disable it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250228004534.3428681-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When the kernel is compiled without LED framework support the
rtl8366rb fails to build like this:
rtl8366rb.o: in function `rtl8366rb_setup_led':
rtl8366rb.c:953:(.text.unlikely.rtl8366rb_setup_led+0xe8):
undefined reference to `led_init_default_state_get'
rtl8366rb.c:980:(.text.unlikely.rtl8366rb_setup_led+0x240):
undefined reference to `devm_led_classdev_register_ext'
As this is constantly coming up in different randconfig builds,
bite the bullet and create a separate file for the offending
code, split out a header with all stuff needed both in the
core driver and the leds code.
Add a new bool Kconfig option for the LED compile target, such
that it depends on LEDS_CLASS=y || LEDS_CLASS=RTL8366RB
which make LED support always available when LEDS_CLASS is
compiled into the kernel and enforce that if the LEDS_CLASS
is a module, then the RTL8366RB driver needs to be a module
as well so that modprobe can resolve the dependencies.
Fixes: 32d6170054 ("net: dsa: realtek: add LED drivers for rtl8366rb")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202502070525.xMUImayb-lkp@intel.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM53101 is a ethernet switch, very similar to the BCM53115.
Enable support for it, in the existing b53 dsa driver.
Signed-off-by: Torben Nielsen <torben.nielsen@prevas.dk>
Signed-off-by: Claus Stovgaard <claus.stovgaard@prevas.dk>
Link: https://patch.msgid.link/20250217080503.1390282-1-claus.stovgaard@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As all PCS are using the neg_mode parameter rather than the legacy
an_mode, remove the ability to use the legacy an_mode. We remove the
tests in the phylink code, unconditionally passing the PCS neg_mode
parameter to PCS methods, and remove setting the flag from drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tidPn-0040hd-2R@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert mt7530 to use phylink managed EEE. When enabling EEE, we set
both PMCR_FORCE_EEE1G and PMCR_FORCE_EEE100 irrespective of the speed,
and clear them both when disabling.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1thR9q-003vXI-Cp@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the helper of_get_available_child_by_name() to simplify
sja1105_mdiobus_register().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify a5psw_probe() by using of_get_available_child_by_name().
While at it, move of_node_put(mdio) inside the if block to avoid code
duplication.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core
----
- More core refactoring to reduce the RTNL lock contention,
including preparatory work for the per-network namespace RTNL lock,
replacing RTNL lock with a per device-one to protect NAPI-related
net device data and moving synchronize_net() calls outside such
lock.
- Extend drop reasons usage, adding net scheduler, AF_UNIX, bridge and
more specific TCP coverage.
- Reduce network namespace tear-down time by removing per-subsystems
synchronize_net() in tipc and sched.
- Add flow label selector support for fib rules, allowing traffic
redirection based on such header field.
Netfilter
---------
- Do not remove netdev basechain when last device is gone, allowing
netdev basechains without devices.
- Revisit the flowtable teardown strategy, dealing better with fin,
reset and re-open events.
- Scale-up IP-vs connection dumping by avoiding linear search on
each restart.
Protocols
---------
- A significant XDP socket refactor, consolidating and optimizing
several helpers into the core
- Better scaling of ICMP rate-limiting, by removing false-sharing in
inet peers handling.
- Introduces netlink notifications for multicast IPv4 and IPv6
address changes.
- Add ipsec support for IP-TFS/AggFrag encapsulation, allowing
aggregation and fragmentation of the inner IP.
- Add sysctl to configure TIME-WAIT reuse delay for TCP sockets,
to avoid local port exhaustion issues when the average connection
lifetime is very short.
- Support updating keys (re-keying) for connections using kernel
TLS (for TLS 1.3 only).
- Support ipv4-mapped ipv6 address clients in smc-r v2.
- Add support for jumbo data packet transmission in RxRPC sockets,
gluing multiple data packets in a single UDP packet.
- Support RxRPC RACK-TLP to manage packet loss and retransmission in
conjunction with the congestion control algorithm.
Driver API
----------
- Introduce a unified and structured interface for reporting PHY
statistics, exposing consistent data across different H/W via
ethtool.
- Make timestamping selectable, allow the user to select the desired
hwtstamp provider (PHY or MAC) administratively.
- Add support for configuring a header-data-split threshold (HDS)
value via ethtool, to deal with partial or buggy H/W implementation.
- Consolidate DSA drivers Energy Efficiency Ethernet support.
- Add EEE management to phylink, making use of the phylib
implementation.
- Add phylib support for in-band capabilities negotiation.
- Simplify how phylib-enabled mac drivers expose the supported
interfaces.
Tests and tooling
-----------------
- Make the YNL tool package-friendly to make it easier to deploy it
separately from the kernel.
- Increase TCP selftest coverage importing several packetdrill
test-cases.
- Regenerate the ethtool uapi header from the YNL spec,
to ease maintenance and future development.
- Add YNL support for decoding the link types used in net
self-tests, allowing a single build to run both net and
drivers/net.
Drivers
-------
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- add cross E-Switch QoS support
- add SW Steering support for ConnectX-8
- implement support for HW-Managed Flow Steering, improving the
rule deletion/insertion rate
- support for multi-host LAG
- Intel (ixgbe, ice, igb):
- ice: add support for devlink health events
- ixgbe: add initial support for E610 chipset variant
- igb: add support for AF_XDP zero-copy
- Meta:
- add support for basic RSS config
- allow changing the number of channels
- add hardware monitoring support
- Broadcom (bnxt):
- implement TCP data split and HDS threshold ethtool support,
enabling Device Memory TCP.
- Marvell Octeon:
- implement egress ipsec offload support for the cn10k family
- Hisilicon (HIBMC):
- implement unicast MAC filtering
- Ethernet NICs embedded and virtual:
- Convert UDP tunnel drivers to NETDEV_PCPU_STAT_DSTATS, avoiding
contented atomic operations for drop counters
- Freescale:
- quicc: phylink conversion
- enetc: support Tx and Rx checksum offload and improve TSO
performances
- MediaTek:
- airoha: introduce support for ETS and HTB Qdisc offload
- Microchip:
- lan78XX USB: preparation work for phylink conversion
- Synopsys (stmmac):
- support DWMAC IP on NXP Automotive SoCs S32G2xx/S32G3xx/S32R45
- refactor EEE support to leverage the new driver API
- optimize DMA and cache access to increase raw RX performances
by 40%
- TI:
- icssg-prueth: add multicast filtering support for VLAN
interface
- netkit:
- add ability to configure head/tailroom
- VXLAN:
- accepts packets with user-defined reserved bit
- Ethernet switches:
- Microchip:
- lan969x: add RGMII support
- lan969x: improve TX and RX performance using the FDMA engine
- nVidia/Mellanox:
- move Tx header handling to PCI driver, to ease XDP support
- Ethernet PHYs:
- Texas Instruments DP83822:
- add support for GPIO2 clock output
- Realtek:
- 8169: add support for RTL8125D rev.b
- rtl822x: add hwmon support for the temperature sensor
- Microchip:
- add support for RDS PTP hardware
- consolidate periodic output signal generation
- CAN:
- several DT-bindings to DT schema conversions
- tcan4x5x:
- add HW standby support
- support nWKRQ voltage selection
- kvaser:
- allowing Bus Error Reporting runtime configuration
- WiFi:
- the on-going Multi-Link Operation (MLO) effort continues, affecting
both the stack and in drivers
- mac80211/cfg80211:
- Emergency Preparedness Communication Services (EPCS) station mode
support
- support for adding and removing station links for MLO
- add support for WiFi 7/EHT mesh over 320 MHz channels
- report Tx power info for each link
- RealTek (rtw88):
- enable USB Rx aggregation and USB 3 to improve performance
- LED support
- RealTek (rtw89):
- refactor power save to support Multi-Link Operations
- add support for RTL8922AE-VS variant
- MediaTek (mt76):
- single wiphy multiband support (preparation for MLO)
- p2p device support
- add TP-Link TXE50UH USB adapter support
- Qualcomm (ath10k):
- support for the QCA6698AQ IP core
- Qualcomm (ath12k):
- enable MLO for QCN9274
- Bluetooth:
- Allow sysfs to trigger hdev reset, to allow recovering devices
not responsive from user-space
- MediaTek: add support for MT7922, MT7925, MT7921e devices
- Realtek: add support for RTL8851BE devices
- Qualcomm: add support for WCN785x devices
- ISO: allow BIG re-sync
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=hrsp
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"This is slightly smaller than usual, with the most interesting work
being still around RTNL scope reduction.
Core:
- More core refactoring to reduce the RTNL lock contention, including
preparatory work for the per-network namespace RTNL lock, replacing
RTNL lock with a per device-one to protect NAPI-related net device
data and moving synchronize_net() calls outside such lock.
- Extend drop reasons usage, adding net scheduler, AF_UNIX, bridge
and more specific TCP coverage.
- Reduce network namespace tear-down time by removing per-subsystems
synchronize_net() in tipc and sched.
- Add flow label selector support for fib rules, allowing traffic
redirection based on such header field.
Netfilter:
- Do not remove netdev basechain when last device is gone, allowing
netdev basechains without devices.
- Revisit the flowtable teardown strategy, dealing better with fin,
reset and re-open events.
- Scale-up IP-vs connection dumping by avoiding linear search on each
restart.
Protocols:
- A significant XDP socket refactor, consolidating and optimizing
several helpers into the core
- Better scaling of ICMP rate-limiting, by removing false-sharing in
inet peers handling.
- Introduces netlink notifications for multicast IPv4 and IPv6
address changes.
- Add ipsec support for IP-TFS/AggFrag encapsulation, allowing
aggregation and fragmentation of the inner IP.
- Add sysctl to configure TIME-WAIT reuse delay for TCP sockets, to
avoid local port exhaustion issues when the average connection
lifetime is very short.
- Support updating keys (re-keying) for connections using kernel TLS
(for TLS 1.3 only).
- Support ipv4-mapped ipv6 address clients in smc-r v2.
- Add support for jumbo data packet transmission in RxRPC sockets,
gluing multiple data packets in a single UDP packet.
- Support RxRPC RACK-TLP to manage packet loss and retransmission in
conjunction with the congestion control algorithm.
Driver API:
- Introduce a unified and structured interface for reporting PHY
statistics, exposing consistent data across different H/W via
ethtool.
- Make timestamping selectable, allow the user to select the desired
hwtstamp provider (PHY or MAC) administratively.
- Add support for configuring a header-data-split threshold (HDS)
value via ethtool, to deal with partial or buggy H/W
implementation.
- Consolidate DSA drivers Energy Efficiency Ethernet support.
- Add EEE management to phylink, making use of the phylib
implementation.
- Add phylib support for in-band capabilities negotiation.
- Simplify how phylib-enabled mac drivers expose the supported
interfaces.
Tests and tooling:
- Make the YNL tool package-friendly to make it easier to deploy it
separately from the kernel.
- Increase TCP selftest coverage importing several packetdrill
test-cases.
- Regenerate the ethtool uapi header from the YNL spec, to ease
maintenance and future development.
- Add YNL support for decoding the link types used in net self-tests,
allowing a single build to run both net and drivers/net.
Drivers:
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- add cross E-Switch QoS support
- add SW Steering support for ConnectX-8
- implement support for HW-Managed Flow Steering, improving the
rule deletion/insertion rate
- support for multi-host LAG
- Intel (ixgbe, ice, igb):
- ice: add support for devlink health events
- ixgbe: add initial support for E610 chipset variant
- igb: add support for AF_XDP zero-copy
- Meta:
- add support for basic RSS config
- allow changing the number of channels
- add hardware monitoring support
- Broadcom (bnxt):
- implement TCP data split and HDS threshold ethtool support,
enabling Device Memory TCP.
- Marvell Octeon:
- implement egress ipsec offload support for the cn10k family
- Hisilicon (HIBMC):
- implement unicast MAC filtering
- Ethernet NICs embedded and virtual:
- Convert UDP tunnel drivers to NETDEV_PCPU_STAT_DSTATS, avoiding
contented atomic operations for drop counters
- Freescale:
- quicc: phylink conversion
- enetc: support Tx and Rx checksum offload and improve TSO
performances
- MediaTek:
- airoha: introduce support for ETS and HTB Qdisc offload
- Microchip:
- lan78XX USB: preparation work for phylink conversion
- Synopsys (stmmac):
- support DWMAC IP on NXP Automotive SoCs S32G2xx/S32G3xx/S32R45
- refactor EEE support to leverage the new driver API
- optimize DMA and cache access to increase raw RX performances
by 40%
- TI:
- icssg-prueth: add multicast filtering support for VLAN
interface
- netkit:
- add ability to configure head/tailroom
- VXLAN:
- accepts packets with user-defined reserved bit
- Ethernet switches:
- Microchip:
- lan969x: add RGMII support
- lan969x: improve TX and RX performance using the FDMA engine
- nVidia/Mellanox:
- move Tx header handling to PCI driver, to ease XDP support
- Ethernet PHYs:
- Texas Instruments DP83822:
- add support for GPIO2 clock output
- Realtek:
- 8169: add support for RTL8125D rev.b
- rtl822x: add hwmon support for the temperature sensor
- Microchip:
- add support for RDS PTP hardware
- consolidate periodic output signal generation
- CAN:
- several DT-bindings to DT schema conversions
- tcan4x5x:
- add HW standby support
- support nWKRQ voltage selection
- kvaser:
- allowing Bus Error Reporting runtime configuration
- WiFi:
- the on-going Multi-Link Operation (MLO) effort continues,
affecting both the stack and in drivers
- mac80211/cfg80211:
- Emergency Preparedness Communication Services (EPCS) station
mode support
- support for adding and removing station links for MLO
- add support for WiFi 7/EHT mesh over 320 MHz channels
- report Tx power info for each link
- RealTek (rtw88):
- enable USB Rx aggregation and USB 3 to improve performance
- LED support
- RealTek (rtw89):
- refactor power save to support Multi-Link Operations
- add support for RTL8922AE-VS variant
- MediaTek (mt76):
- single wiphy multiband support (preparation for MLO)
- p2p device support
- add TP-Link TXE50UH USB adapter support
- Qualcomm (ath10k):
- support for the QCA6698AQ IP core
- Qualcomm (ath12k):
- enable MLO for QCN9274
- Bluetooth:
- Allow sysfs to trigger hdev reset, to allow recovering devices
not responsive from user-space
- MediaTek: add support for MT7922, MT7925, MT7921e devices
- Realtek: add support for RTL8851BE devices
- Qualcomm: add support for WCN785x devices
- ISO: allow BIG re-sync"
* tag 'net-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1386 commits)
net/rose: prevent integer overflows in rose_setsockopt()
net: phylink: fix regression when binding a PHY
net: ethernet: ti: am65-cpsw: streamline TX queue creation and cleanup
net: ethernet: ti: am65-cpsw: streamline RX queue creation and cleanup
net: ethernet: ti: am65-cpsw: ensure proper channel cleanup in error path
ipv6: Convert inet6_rtm_deladdr() to per-netns RTNL.
ipv6: Convert inet6_rtm_newaddr() to per-netns RTNL.
ipv6: Move lifetime validation to inet6_rtm_newaddr().
ipv6: Set cfg.ifa_flags before device lookup in inet6_rtm_newaddr().
ipv6: Pass dev to inet6_addr_add().
ipv6: Convert inet6_ioctl() to per-netns RTNL.
ipv6: Hold rtnl_net_lock() in addrconf_init() and addrconf_cleanup().
ipv6: Hold rtnl_net_lock() in addrconf_dad_work().
ipv6: Hold rtnl_net_lock() in addrconf_verify_work().
ipv6: Convert net.ipv6.conf.${DEV}.XXX sysctl to per-netns RTNL.
ipv6: Add __in6_dev_get_rtnl_net().
net: stmmac: Drop redundant skb_mark_for_recycle() for SKB frags
net: mii: Fix the Speed display when the network cable is not connected
sysctl net: Remove macro checks for CONFIG_SYSCTL
eth: bnxt: update header sizing defaults
...
1) Per-CPU kthreads must stay affine to a single CPU and never execute
relevant code on any other CPU. This is currently handled by smpboot
code which takes care of CPU-hotplug operations. Affinity here is
a correctness constraint.
2) Some kthreads _have_ to be affine to a specific set of CPUs and can't
run anywhere else. The affinity is set through kthread_bind_mask()
and the subsystem takes care by itself to handle CPU-hotplug
operations. Affinity here is assumed to be a correctness constraint.
3) Per-node kthreads _prefer_ to be affine to a specific NUMA node. This
is not a correctness constraint but merely a preference in terms of
memory locality. kswapd and kcompactd both fall into this category.
The affinity is set manually like for any other task and CPU-hotplug
is supposed to be handled by the relevant subsystem so that the task
is properly reaffined whenever a given CPU from the node comes up.
Also care should be taken so that the node affinity doesn't cross
isolated (nohz_full) cpumask boundaries.
4) Similar to the previous point except kthreads have a _preferred_
affinity different than a node. Both RCU boost kthreads and RCU
exp kworkers fall into this category as they refer to "RCU nodes"
from a distinctly distributed tree.
Currently the preferred affinity patterns (3 and 4) have at least 4
identified users, with more or less success when it comes to handle
CPU-hotplug operations and CPU isolation. Each of which do it in its own
ad-hoc way.
This is an infrastructure proposal to handle this with the following API
changes:
_ kthread_create_on_node() automatically affines the created kthread to
its target node unless it has been set as per-cpu or bound with
kthread_bind[_mask]() before the first wake-up.
- kthread_affine_preferred() is a new function that can be called right
after kthread_create_on_node() to specify a preferred affinity
different than the specified node.
When the preferred affinity can't be applied because the possible
targets are offline or isolated (nohz_full), the kthread is affine
to the housekeeping CPUs (which means to all online CPUs most of the
time or only the non-nohz_full CPUs when nohz_full= is set).
kswapd, kcompactd, RCU boost kthreads and RCU exp kworkers have been
converted, along with a few old drivers.
Summary of the changes:
* Consolidate a bunch of ad-hoc implementations of kthread_run_on_cpu()
* Introduce task_cpu_fallback_mask() that defines the default last
resort affinity of a task to become nohz_full aware
* Add some correctness check to ensure kthread_bind() is always called
before the first kthread wake up.
* Default affine kthread to its preferred node.
* Convert kswapd / kcompactd and remove their halfway working ad-hoc
affinity implementation
* Implement kthreads preferred affinity
* Unify kthread worker and kthread API's style
* Convert RCU kthreads to the new API and remove the ad-hoc affinity
implementation.
-----BEGIN PGP SIGNATURE-----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=g8In
-----END PGP SIGNATURE-----
Merge tag 'kthread-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks
Pull kthread updates from Frederic Weisbecker:
"Kthreads affinity follow either of 4 existing different patterns:
1) Per-CPU kthreads must stay affine to a single CPU and never
execute relevant code on any other CPU. This is currently handled
by smpboot code which takes care of CPU-hotplug operations.
Affinity here is a correctness constraint.
2) Some kthreads _have_ to be affine to a specific set of CPUs and
can't run anywhere else. The affinity is set through
kthread_bind_mask() and the subsystem takes care by itself to
handle CPU-hotplug operations. Affinity here is assumed to be a
correctness constraint.
3) Per-node kthreads _prefer_ to be affine to a specific NUMA node.
This is not a correctness constraint but merely a preference in
terms of memory locality. kswapd and kcompactd both fall into this
category. The affinity is set manually like for any other task and
CPU-hotplug is supposed to be handled by the relevant subsystem so
that the task is properly reaffined whenever a given CPU from the
node comes up. Also care should be taken so that the node affinity
doesn't cross isolated (nohz_full) cpumask boundaries.
4) Similar to the previous point except kthreads have a _preferred_
affinity different than a node. Both RCU boost kthreads and RCU
exp kworkers fall into this category as they refer to "RCU nodes"
from a distinctly distributed tree.
Currently the preferred affinity patterns (3 and 4) have at least 4
identified users, with more or less success when it comes to handle
CPU-hotplug operations and CPU isolation. Each of which do it in its
own ad-hoc way.
This is an infrastructure proposal to handle this with the following
API changes:
- kthread_create_on_node() automatically affines the created kthread
to its target node unless it has been set as per-cpu or bound with
kthread_bind[_mask]() before the first wake-up.
- kthread_affine_preferred() is a new function that can be called
right after kthread_create_on_node() to specify a preferred
affinity different than the specified node.
When the preferred affinity can't be applied because the possible
targets are offline or isolated (nohz_full), the kthread is affine to
the housekeeping CPUs (which means to all online CPUs most of the time
or only the non-nohz_full CPUs when nohz_full= is set).
kswapd, kcompactd, RCU boost kthreads and RCU exp kworkers have been
converted, along with a few old drivers.
Summary of the changes:
- Consolidate a bunch of ad-hoc implementations of
kthread_run_on_cpu()
- Introduce task_cpu_fallback_mask() that defines the default last
resort affinity of a task to become nohz_full aware
- Add some correctness check to ensure kthread_bind() is always
called before the first kthread wake up.
- Default affine kthread to its preferred node.
- Convert kswapd / kcompactd and remove their halfway working ad-hoc
affinity implementation
- Implement kthreads preferred affinity
- Unify kthread worker and kthread API's style
- Convert RCU kthreads to the new API and remove the ad-hoc affinity
implementation"
* tag 'kthread-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks:
kthread: modify kernel-doc function name to match code
rcu: Use kthread preferred affinity for RCU exp kworkers
treewide: Introduce kthread_run_worker[_on_cpu]()
kthread: Unify kthread_create_on_cpu() and kthread_create_worker_on_cpu() automatic format
rcu: Use kthread preferred affinity for RCU boost
kthread: Implement preferred affinity
mm: Create/affine kswapd to its preferred node
mm: Create/affine kcompactd to its preferred node
kthread: Default affine kthread to its preferred NUMA node
kthread: Make sure kthread hasn't started while binding it
sched,arm64: Handle CPU isolation on last resort fallback rq selection
arm64: Exclude nohz_full CPUs from 32bits el0 support
lib: test_objpool: Use kthread_run_on_cpu()
kallsyms: Use kthread_run_on_cpu()
soc/qman: test: Use kthread_run_on_cpu()
arm/bL_switcher: Use kthread_run_on_cpu()
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the linkage between the DSA user port ethtool_ops :: get_ts_info
and the implementation from the Ocelot switch library.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250116104628.123555-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass the current neg_mode into the .pcs_get_state() method. Update all
users of phylink PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeT-000Et3-4L@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
kthread_create() creates a kthread without running it yet. kthread_run()
creates a kthread and runs it.
On the other hand, kthread_create_worker() creates a kthread worker and
runs it.
This difference in behaviours is confusing. Also there is no way to
create a kthread worker and affine it using kthread_bind_mask() or
kthread_affine_preferred() before starting it.
Consolidate the behaviours and introduce kthread_run_worker[_on_cpu]()
that behaves just like kthread_run(). kthread_create_worker[_on_cpu]()
will now only create a kthread worker without starting it.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
mv88e6xxx_get_mac_eee() is no longer called by the core DSA code.
Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tUllK-007Uz9-D7@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mt753x_get_mac_eee() is no longer called by the core DSA code. Remove
it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/E1tUllF-007Uz3-95@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dsa_user_get_eee() calls the DSA switch get_mac_eee() method followed
by phylink_ethtool_get_eee(), which goes on to call
phy_ethtool_get_eee(). This overwrites all members of the passed
ethtool_keee, which means anything written by the DSA switch
get_mac_eee() method will be discarded.
Remove setting any members in mt753x_get_mac_eee().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/E1tUlku-007Uyc-RP@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dsa_user_get_eee() calls the DSA switch get_mac_eee() method followed
by phylink_ethtool_get_eee(), which goes on to call
phy_ethtool_get_eee(). This overwrites all members of the passed
ethtool_keee, which means anything written by the DSA switch
get_mac_eee() method will be discarded.
Remove setting any members in ksz_get_mac_eee().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tUlkp-007UyW-OR@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PTP driver code only works for certain KSZ switches like KSZ9477,
KSZ9567, LAN937X and their varieties. This code is enabled by kernel
configuration CONFIG_NET_DSA_MICROCHIP_KSZ_PTP. As the DSA driver is
common to work with all KSZ switches this PTP code is not appropriate
for other unsupported switches. The ptp_capable indication is added to
the chip data structure to signal whether to execute those code.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/20241218020240.70601-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ DSA driver starts a timer to read MIB counters periodically to
avoid count overrun. During system suspend this will give an error for
not able to write to register as the SPI system returns an error when
it is in suspend state. This implementation stops the timer when the
system goes into suspend and restarts it when resumed.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218020311.70628-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The aging count is not a simple 20-bit value but comprises a 3-bit
multiplier and a 20-bit second time. The code tries to use the
original multiplier which is 4 as the second count is still 300 seconds
by default.
As the 20-bit number is now too large for practical use there is an option
to interpret it as microseconds instead of seconds.
Fixes: 2c119d9982 ("net: dsa: microchip: add the support for set_ageing_time")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218020224.70590-3-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The aging count is not a simple 11-bit value but comprises a 3-bit
multiplier and an 8-bit second count. The code tries to use the
original multiplier which is 4 as the second count is still 300 seconds
by default.
Fixes: 2c119d9982 ("net: dsa: microchip: add the support for set_ageing_time")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218020224.70590-2-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
wait_for_complete_timeout() expects a timeout in jiffies. With the
driver, some call sites converted QCA8K_ETHERNET_TIMEOUT to jiffies,
others did not. Make the code consistent by changes the #define to
include a call to msecs_to_jiffies, and remove all other calls to
msecs_to_jiffies.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: from Christian would be very welcome.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8d7ae22ae9 ("net: dsa: microchip: KSZ9477 register regmap
alignment to 32 bit boundaries") fixed an issue whereby regmap_reg_range
did not allow writes as 32 bit words to KSZ9477 PHY registers, this fix
for KSZ9896 is adapted from there as the same errata is present in
KSZ9896C as "Module 5: Certain PHY registers must be written as pairs
instead of singly" the explanation below is likewise taken from this
commit.
The commit provided code
to apply "Module 6: Certain PHY registers must be written as pairs instead
of singly" errata for KSZ9477 as this chip for certain PHY registers
(0xN120 to 0xN13F, N=1,2,3,4,5) must be accessed as 32 bit words instead
of 16 or 8 bit access.
Otherwise, adjacent registers (no matter if reserved or not) are
overwritten with 0x0.
Without this patch some registers (e.g. 0x113c or 0x1134) required for 32
bit access are out of valid regmap ranges.
As a result, following error is observed and KSZ9896 is not properly
configured:
ksz-switch spi1.0: can't rmw 32bit reg 0x113c: -EIO
ksz-switch spi1.0: can't rmw 32bit reg 0x1134: -EIO
ksz-switch spi1.0 lan1 (uninitialized): failed to connect to PHY: -EIO
ksz-switch spi1.0 lan1 (uninitialized): error -5 setting up PHY for tree 0, switch 0, port 0
The solution is to modify regmap_reg_range to allow accesses with 4 bytes
boundaries.
Fixes: 5c844d57aa ("net: dsa: microchip: fix writes to phy registers >= 0x10")
Signed-off-by: Jesse Van Gavere <jesse.vangavere@scioteq.com>
Link: https://patch.msgid.link/20241211092932.26881-1-jesse.vangavere@scioteq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by reusing the ksz_validate_eee()
method as a template, renaming the function, changing the return type
and values, and removing it from the ksz_set_mac_eee() and
ksz_get_mac_eee() methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14Z-006cZs-6o@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by using the generic helper as all
user ports support EEE.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14U-006cZm-2K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by using the generic helper as all
user ports support EEE.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14O-006cZg-VM@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by using the generic helper as all
user ports support EEE.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14J-006cZa-Rh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method to indicate that EEE is not
supported by two switch variants, rather than making these checks in
the .set_mac_eee() and .get_mac_eee() methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14E-006cZU-Nc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With this port schedule:
tc qdisc replace dev $send_if parent root handle 100 taprio \
num_tc 8 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
map 0 1 2 3 4 5 6 7 \
base-time 0 cycle-time 10000 \
sched-entry S 01 1250 \
sched-entry S 02 1250 \
sched-entry S 04 1250 \
sched-entry S 08 1250 \
sched-entry S 10 1250 \
sched-entry S 20 1250 \
sched-entry S 40 1250 \
sched-entry S 80 1250 \
flags 2
ptp4l would fail to take TX timestamps of Pdelay_Resp messages like this:
increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
ptp4l[4134.168]: port 2: send peer delay response failed
It turns out that the driver can't take their TX timestamps because it
can't transmit them in the first place. And there's nothing special
about the Pdelay_Resp packets - they're just regular 68 byte packets.
But with this taprio configuration, the switch would refuse to send even
the ETH_ZLEN minimum packet size.
This should have definitely not been the case. When applying the taprio
config, the driver prints:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
and thus, everything under 132 bytes - ETH_FCS_LEN should have been sent
without problems. Yet it's not.
For the forwarding path, the configuration is fine, yet packets injected
from Linux get stuck with this schedule no matter what.
The first hint that the static guard bands are the cause of the problem
is that reverting Michael Walle's commit 297c4de6f7 ("net: dsa: felix:
re-enable TAS guard band mode") made things work. It must be that the
guard bands are calculated incorrectly.
I remembered that there is a magic constant in the driver, set to 33 ns
for no logical reason other than experimentation, which says "never let
the static guard bands get so large as to leave less than this amount of
remaining space in the time slot, because the queue system will refuse
to schedule packets otherwise, and they will get stuck". I had a hunch
that my previous experimentally-determined value was only good for
packets coming from the forwarding path, and that the CPU injection path
needed more.
I came to the new value of 35 ns through binary search, after seeing
that with 544 ns (the bit time required to send the Pdelay_Resp packet
at gigabit) it works. Again, this is purely experimental, there's no
logic and the manual doesn't say anything.
The new driver prints for this schedule look like this:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
So yes, the maximum MTU is now even smaller by 1 byte than before.
This is maybe counter-intuitive, but makes more sense with a diagram of
one time slot.
Before:
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<----><---------------------------------------------->
33 ns 1217 ns static guard band
useful
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<-----><--------------------------------------------->
35 ns 1215 ns static guard band
useful
The static guard band implemented by this switch hardware directly
determines the maximum allowable MTU for that traffic class. The larger
it is, the earlier the switch will stop scheduling frames for
transmission, because otherwise they might overrun the gate close time
(and avoiding that is the entire purpose of Michael's patch).
So, we now have guard bands smaller by 2 ns, thus, in this particular
case, we lose a byte of the maximum MTU.
Fixes: 11afdc6526 ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20241210132640.3426788-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of the sanity checks in pack() and unpack() can be covered at
compile time. There is only one exception, and that is truncation of the
uval during a pack() operation.
We'd like the error-less __pack() to catch that condition as well. But
at the same time, it is currently the responsibility of consumer drivers
(currently just sja1105) to print anything at all when this error
occurs, and then discard the return code.
We can just print a loud warning in the library code and continue with
the truncated __pack() operation. In practice, having the warning is
very important, see commit 24deec6b9e ("net: dsa: sja1105: disallow
C45 transactions on the BASE-TX MDIO bus") where the bug was caught
exactly by noticing this print.
Add the first print to the packing library, and at the same time remove
the print for the same condition from the sja1105 driver, to avoid
double printing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241210-packing-pack-fields-and-ice-implementation-v10-2-ee56a47479ac@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Different families of switches have different statistics available.
This information is current hard coded into functions, however this
information will also soon be needed when getting statistics from the
RMU. Move it into the info structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241207-v6-13-rc1-net-next-mv88e6xxx-stats-refactor-v1-1-b9960f839846@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In configurations with 2 or more DSA clusters it will fail to allocate
unique MDIO bus names as only the switch ID is used, fix this by using
a combination of the tree ID and switch ID when needed
Signed-off-by: Jesse Van Gavere <jesse.vangavere@scioteq.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241206204202.649912-1-jesse.vangavere@scioteq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LAN9646 switch is a 6-port switch with functions like KSZ9897. It has
4 internal PHYs and 1 SGMII port. The chip id read from hardware is
same as KSZ9477, so software driver needs to create a new chip id and
group allowable functions under its chip data structure to
differentiate the product.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/20241109015705.82685-3-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
qca8k_phy_eth_command() is used to probe the child MDIO bus while the
parent MDIO is locked. This causes lockdep splat, reporting a possible
deadlock. It is not an actually deadlock, because different locks are
used. By making use of mutex_lock_nested() we can avoid this false
positive.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241110175955.3053664-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce ksz_parse_dt_phy_config() to validate and parse PHY
configuration from the device tree for KSZ switches. This function
ensures proper setup of internal PHYs by checking `phy-handle`
properties, verifying expected PHY IDs, and handling parent node
mismatches. Sets the PHY mask on the MII bus if validation is
successful. Returns -EINVAL on configuration errors.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241106075942.1636998-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement side MDIO channel support for LAN937x switches, providing an
alternative to SPI for PHY management alongside existing SPI-based
switch configuration. This is needed to reduce SPI load, as SPI can be
relatively expensive for small packets compared to MDIO support.
Also, implemented static mappings for PHY addresses for various LAN937x
models to support different internal PHY configurations. Since the PHY
address mappings are not equal to the port indexes, this patch also
provides PHY address calculation based on hardware strapping
configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace repeated cleanup code with a single error path using a label.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for accessing PHYs via a side MDIO interface in LAN937x
switches. The existing code already supports accessing PHYs via main
management interfaces, which can be SPI, I2C, or MDIO, depending on the
chip variant. This patch enables using a side MDIO bus, where SPI is
used for the main switch configuration and MDIO for managing the
integrated PHYs. On LAN937x, this is optional, allowing them to operate
in both configurations: SPI only, or SPI + MDIO. Typically, the SPI
interface is used for switch configuration, while MDIO handles PHY
management.
Additionally, update interrupt controller code to support non-linear
port to PHY address mapping, enabling correct interrupt handling for
configurations where PHY addresses do not directly correspond to port
indexes. This change ensures that the interrupt mechanism properly
aligns with the new, flexible PHY address mappings introduced by side
MDIO support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce port_setup_tc callback in mt7530 dsa driver in order to enable
dsa ports rate shaping via hw Token Bucket Filter (TBF) for hw switched
traffic.
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241031-mt7530-tc-offload-v2-1-cb242ad954a0@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These are the preferred way to copy ethtool strings.
Avoids incrementing pointers all over the place.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(for hellcreek driver)
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20241028044828.1639668-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'ports_fwnode' is initialized via device_get_named_child_node(), which
requires a call to fwnode_handle_put() when the variable is no longer
required to avoid leaking memory.
Add the missing fwnode_handle_put() after 'ports_fwnode' has been used
and is no longer required.
Fixes: 94a2a84f5e ("net: dsa: mv88e6xxx: Support LED control")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6393X family of devices can run its cycle counter off
an internal 250MHz clock instead of an external 125MHz one.
Add support for this cycle counter period by adding another set
of coefficients and lowering the periodic cycle counter read interval
to compensate for faster overflows at the increased frequency.
Otherwise, the PHC runs at 2x real time in userspace and cannot be
synchronized.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of relying on a fixed mapping of hardware family to cycle
counter frequency, pull this information from the
MV88E6XXX_TAI_CLOCK_PERIOD register.
This lets us support switches whose cycle counter frequencies depend on
board design.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of having them as individual fields in ptp_ops, wrap the
coefficients in a separate struct so they can be referenced together.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The well-known errata regarding EEE not being functional on various KSZ
switches has been refactored a few times. Recently the refactoring has
excluded several switches that the errata should also apply to.
Disable EEE for additional switches with this errata and provide
additional comments referring to the public errata document.
The original workaround for the errata was applied with a register
write to manually disable the EEE feature in MMD 7:60 which was being
applied for KSZ9477/KSZ9897/KSZ9567 switch ID's.
Then came commit 26dd2974c5 ("net: phy: micrel: Move KSZ9477 errata
fixes to PHY driver") and commit 6068e6d7ba ("net: dsa: microchip:
remove KSZ9477 PHY errata handling") which moved the errata from the
switch driver to the PHY driver but only for PHY_ID_KSZ9477 (PHY ID)
however that PHY code was dead code because an entry was never added
for PHY_ID_KSZ9477 via MODULE_DEVICE_TABLE.
This was apparently realized much later and commit 54a4e5c163 ("net:
phy: micrel: add Microchip KSZ 9477 to the device table") added the
PHY_ID_KSZ9477 to the PHY driver but as the errata was only being
applied to PHY_ID_KSZ9477 it's not completely clear what switches
that relates to.
Later commit 6149db4997 ("net: phy: micrel: fix KSZ9477 PHY issues
after suspend/resume") breaks this again for all but KSZ9897 by only
applying the errata for that PHY ID.
Following that this was affected with commit 08c6d8bae48c("net: phy:
Provide Module 4 KSZ9477 errata (DS80000754C)") which removes
the blatant register write to MMD 7:60 and replaces it by
setting phydev->eee_broken_modes = -1 so that the generic phy-c45 code
disables EEE but this is only done for the KSZ9477_CHIP_ID (Switch ID).
Lastly commit 0411f73c13 ("net: dsa: microchip: disable EEE for
KSZ8567/KSZ9567/KSZ9896/KSZ9897.") adds some additional switches
that were missing to the errata due to the previous changes.
This commit adds an additional set of switches.
Fixes: 0411f73c13 ("net: dsa: microchip: disable EEE for KSZ8567/KSZ9567/KSZ9896/KSZ9897.")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241018160658.781564-1-tharvey@gateworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cross-merge networking fixes after downstream PR (net-6.12-rc4).
Conflicts:
107a034d5c ("net/mlx5: qos: Store rate groups in a qos domain")
1da9cfd6c4 ("net/mlx5: Unregister notifier on eswitch init failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
mv88e6393x_port_set_policy doesn't correctly shift the ptr value when
converting the policy format between the old and new styles, so the
target register ends up with the ptr being written over the data bits.
Shift the pointer to align with the format expected by
mv88e6393x_port_policy_write().
Fixes: 6584b26020 ("net: dsa: mv88e6xxx: implement .port_set_policy for Amethyst")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241016040822.3917-1-peter@rashleigh.ca>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Rather than returning an EOPNOTSUPP error pointer when the switch
has no support for PCS, return NULL to indicate that no PCS is
required.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Similar to the situation described for sja1105 in commit 1f9fc48fd3
("net: dsa: sja1105: fix reception from VLAN-unaware bridges"), the
vsc73xx driver uses tag_8021q and doesn't need the ds->untag_bridge_pvid
request. In fact, this option breaks packet reception.
The ds->untag_bridge_pvid option strips VLANs from packets received on
VLAN-unaware bridge ports. But those VLANs should already be stripped
by tag_vsc73xx_8021q.c as part of vsc73xx_rcv() - they are not VLANs in
VLAN-unaware mode, but DSA tags. Thus, dsa_software_vlan_untag() tries
to untag a VLAN that doesn't exist, corrupting the packet.
Fixes: 93e4649efa ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20241014153041.1110364-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the Marvell datasheet the 88E6361 has two VTU pages
(4k VIDs per page) so the max_vid should be 8191, not 4095.
In the current implementation mv88e6xxx_vtu_walk() gives unexpected
results because of this error. I verified that mv88e6xxx_vtu_walk()
works correctly on the MV88E6361 with this patch in place.
Fixes: 12899f2998 ("net: dsa: mv88e6xxx: enable support for 88E6361 switch")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241014204342.5852-1-peter@rashleigh.ca
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prior to this patch ksz_ptp_msg_irq_setup() uses snprintf() to copy
strings. It does so by passing strings as the format argument of
snprintf(). This appears to be safe, due to the absence of format
specifiers in the strings, which are declared within the same function.
But nonetheless GCC 14 warns about it:
.../ksz_ptp.c:1109:55: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
1109 | snprintf(ptpmsg_irq->name, sizeof(ptpmsg_irq->name), name[n]);
| ^~~~~~~
.../ksz_ptp.c:1109:55: note: treat the string as an argument to avoid this
1109 | snprintf(ptpmsg_irq->name, sizeof(ptpmsg_irq->name), name[n]);
| ^
| "%s",
As what we are really dealing with here is a string copy, it seems make
sense to use a function designed for this purpose. In this case null
padding is not required, so strscpy is appropriate. And as the
destination is an array of fixed size, the 2-argument variant may be used.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241014-string-thing-v2-1-b9b29625060a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The err value in mv88e6xxx_region_atu_snapshot is now potentially
uninitialised on return. Initialise err as 0.
Fixes: ada5c3229b ("net: dsa: mv88e6xxx: Add FID map cache")
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241009212319.1045176-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a cached FID bitmap. This mitigates the need to walk all VTU entries
to find the next free FID.
When flushing the VTU (during init), zero the FID bitmap. Use and
manipulate this bitmap from now on, instead of reading HW for the FID
map.
The repeated VTU walks are costly and can take ~40 mins if ~4000 vlans
are added. Caching the FID map reduces this time to <2 mins.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241006212905.3142976-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All modern chips support and need the 10_100 bit set for supporting jumbo
frames on 10/100 ports, so instead of enabling it only for 583XX enable
it for everything except bcm63xx, where the bit is writeable, but does
nothing.
Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds
without the bit set.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
While BCM5325/5365 do not support jumbo frames, they do support slightly
oversized frames, so do not error out if requesting a supported MTU for
them.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
BCM5325/BCM5365 do not support jumbo frames, so we should not report a
jumbo frame mtu for them. But they do support so called "oversized"
frames up to 1536 bytes long by default, so report an appropriate MTU.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Accessing device registers seems to be not reliable, the chip
revision is sometimes detected wrongly (0 instead of expected 1).
Ensure that the chip reset is performed via reset GPIO and then
wait for 'Device Ready' status in HW_CFG register before doing
any register initializations.
Cc: stable@vger.kernel.org
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
[alex: reworked using read_poll_timeout()]
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20241004113655.3436296-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/dsa to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/36da477cb9fa0bffec32d50c2cf3d18e94a0e7e3.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SF2 crossbar register is a packed bitfield, giving the index of the
external port selected for each of the internal ports. On BCM4908 (the
only currently-supported switch family with a crossbar), there are 2
internal ports and 3 external ports, so there are 2 bits per internal
port.
The driver currently conflates the "bits per port" and "number of ports"
concepts, lumping both into the `num_crossbar_int_ports` field. Since it
is currently only possible for either of these counts to have a value of
2, there is no behavioral error resulting from this situation for now.
Make the code more readable (and support the future possibility of
larger crossbars) by adding a `num_crossbar_ext_bits` field to represent
the "bits per port" count and relying on this where appropriate instead.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241003212301.1339647-1-CFSworks@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds control over the hardware LEDs in the Marvell
MV88E6xxx DSA switch and enables it for MV88E6352.
This fixes an imminent problem on the Inteno XG6846 which
has a WAN LED that simply do not work with hardware
defaults: driver amendment is necessary.
The patch is modeled after Christian Marangis LED support
code for the QCA8k DSA switch, I got help with the register
definitions from Tim Harvey.
After this patch it is possible to activate hardware link
indication like this (or with a similar script):
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link
This makes the green link indicator come up on any link
speed. It is also possible to be more elaborate, like this:
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link_1000
cd /sys/class/leds/Marvell\ 88E6352:05:01:amber:wan/
echo netdev > trigger
echo 1 > link_100
Making the green LED come on for a gigabit link and the
amber LED come on for a 100 mbit link.
Each port has 2 LED slots (the hardware may use just one or
none) and the hardware triggers are specified in four bits per
LED, and some of the hardware triggers are only available on the
SFP (fiber) uplink. The restrictions are described in the
port.h header file where the registers are described. For
example, selector 1 set for LED 1 on port 5 or 6 will indicate
Fiber 1000 (gigabit) and activity with a blinking LED, but
ONLY for an SFP connection. If port 5/6 is used with something
not SFP, this selector is a noop: something else need to be
selected.
After the previous series rewriting the MV88E6xxx DT
bindings to use YAML a "leds" subnode is already valid
for each port, in my scratch device tree it looks like
this:
leds {
#address-cells = <1>;
#size-cells = <0>;
led@0 {
reg = <0>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_LAN;
default-state = "off";
linux,default-trigger = "netdev";
};
led@1 {
reg = <1>;
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_LAN;
default-state = "off";
};
};
This DT config is not yet configuring everything: when the netdev
default trigger is assigned the hw acceleration callbacks are
not called, and there is no way to set the netdev sub-trigger
type (such as link_1000) from the device tree, such as if you want
a gigabit link indicator. This has to be done from userspace at
this point.
We add LED operations to all switches in the 6352 family:
6172, 6176, 6240 and 6352.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241001-mv88e6xxx-leds-v4-1-cc11c4f49b18@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit introduced an unexpected regression in the sja1105
driver. Packets from VLAN-unaware bridge ports get received correctly,
but the protocol stack can't seem to decode them properly.
For ds->untag_bridge_pvid users (thus also sja1105), the blamed commit
did introduce a functional change: dsa_switch_rcv() used to call
dsa_untag_bridge_pvid(), which looked like this:
err = br_vlan_get_proto(br, &proto);
if (err)
return skb;
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb) && skb->protocol == htons(proto)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
and now it calls dsa_software_vlan_untag() which has just this:
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
thus lacks any skb->protocol == bridge VLAN protocol check. That check
is deferred until a later check for skb->vlan_proto (in the hwaccel area).
The new code is problematic because, for VLAN-untagged packets,
skb_vlan_untag() blindly takes the 4 bytes starting with the EtherType
and turns them into a hwaccel VLAN tag. This is what breaks the protocol
stack.
It would be tempting to "make it work as before" and only call
skb_vlan_untag() for those packets with the skb->protocol actually
representing a VLAN.
But the premise of the newly introduced dsa_software_vlan_untag() core
function is not wrong. Drivers set ds->untag_bridge_pvid or
ds->untag_vlan_aware_bridge_pvid presumably because they send all
traffic to the CPU reception path as VLAN-tagged. So why should we spend
any additional CPU cycles assuming that the packet may be VLAN-untagged?
And why does the sja1105 driver opt into ds->untag_bridge_pvid if it
doesn't always deliver packets to the CPU as VLAN-tagged?
The answer to the latter question is indeed more interesting: it doesn't
need to. This got done in commit 884be12f85 ("net: dsa: sja1105: add
support for imprecise RX"), because I thought it would be needed, but I
didn't realize that it doesn't actually make a difference.
As explained in the commit message of the blamed patch, ds->untag_bridge_pvid
only makes a difference in the VLAN-untagged receive path of a bridge port.
However, in that operating mode, tag_sja1105.c makes use of VLAN tags
with the ETH_P_SJA1105 TPID, and it decodes and consumes these VLAN tags
as if they were DSA tags (aka tag_8021q operation). Even if commit
884be12f85 ("net: dsa: sja1105: add support for imprecise RX") added
this logic in sja1105_bridge_vlan_add():
/* Always install bridge VLANs as egress-tagged on the CPU port. */
if (dsa_is_cpu_port(ds, port))
flags = 0;
that was for _bridge_ VLANs, which are _not_ committed to hardware
in VLAN-unaware mode (aka the mode where ds->untag_bridge_pvid does
anything at all). Even prior to that change, the tag_8021q VLANs
were always installed as egress-tagged on the CPU port, see
dsa_switch_tag_8021q_vlan_add():
u16 flags = 0; // egress-tagged, non-PVID
if (dsa_port_is_user(dp))
flags |= BRIDGE_VLAN_INFO_UNTAGGED |
BRIDGE_VLAN_INFO_PVID;
err = dsa_port_do_tag_8021q_vlan_add(dp, info->vid,
flags);
if (err)
return err;
Whether the sja1105 driver needs the new flag, ds->untag_vlan_aware_bridge_pvid,
rather than ds->untag_bridge_pvid, is a separate discussion. To fix the
current bug in VLAN-unaware bridge mode, I would argue that the sja1105
driver should not request something it doesn't need, rather than
complicating the core DSA helper. Whereas before the blamed commit, this
setting was harmless, now it has caused breakage.
Fixes: 93e4649efa ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241001140206.50933-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use xpcs_create_pcs_mdiodev() to create the XPCS instance, storing
and using the phylink_pcs pointer internally, rather than dw_xpcs.
Use xpcs_destroy_pcs() to destroy the XPCS instance when we've
finished with it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMk-005ZIj-R3@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call the PCS operations through the ops structure, which avoids needing
to export xpcs internal functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMf-005ZId-Mx@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The static configuration reload saves the port speed in the static
configuration tables by first converting it from the internal
respresentation to the SPEED_xxx ethtool representation, and then
converts it back to restore the setting. This is because
sja1105_adjust_port_config() takes the speed as SPEED_xxx.
However, this is unnecessarily complex. If we split
sja1105_adjust_port_config() up, we can simply save and restore the
mac[port].speed member in the static configuration tables.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMa-005ZIX-If@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Cross-merge networking fixes after downstream PR.
No conflicts (sort of) and no adjacent changes.
This merge reverts commit b3c9e65eb2 ("net: hsr: remove seqnr_lock")
from net, as it was superseded by
commit 430d67bdcb ("net: hsr: Use the seqnr lock for frames received via interlink port.")
in net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TAS module could not be configured when it's running in pending
status. We need disable the module and configure it again. However, the
pending status is not cleared after the module disabled. TC taprio set
will always return busy even it's disabled.
For example, a user uses tc-taprio to configure Qbv and a future
basetime. The TAS module will run in a pending status. There is no way
to reconfigure Qbv, it always returns busy.
Actually the TAS module can be reconfigured when it's disabled. So it
doesn't need to check the pending status if the TAS module is disabled.
After the patch, user can delete the tc taprio configuration to disable
Qbv and reconfigure it again.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Link: https://patch.msgid.link/20240906093550.29985-1-xiaoliang.yang_1@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace ksz8830 with ksz88x3 for CHIP_ID definition and other
strings. This due to KSZ8830 not being an actual switch but the Chip
ID shared among KSZ8863/8873 switches, impossible to differentiate
from their Chip ID or Revision ID registers.
Now all KSZ*_CHIP_ID macros refer to actual, existing switches which
removes confusion.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove macros that are already defined at more appropriate places.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first KSZ8 series implementation was done for a KSZ8795 device but
since several other KSZ8 devices have been added. Rename these files
to adhere to the ksz8 naming convention as already used in most
functions and the existing ksz8.h; add an explanatory note.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the __counted_by compiler attribute to the flexible array member
entries to improve access bounds-checking via CONFIG_UBSAN_BOUNDS and
CONFIG_FORTIFY_SOURCE.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://patch.msgid.link/20240904014956.2035117-1-lihongbo22@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Avoids the need for manual cleanup of_node_put() in early exits
from the loop by using for_each_available_child_of_node_scoped().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Avoid need to manually handle of_node_put() by using
for_each_child_of_node_scoped(), which can simplfy code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This commit introduces implementations of three functions:
.port_fdb_dump
.port_fdb_add
.port_fdb_del
The FDB database organization is the same as in other old Vitesse chips:
It has 2048 rows and 4 columns (buckets). The row index is calculated by
the hash function 'vsc73xx_calc_hash' and the FDB entry must be placed
exactly into row[hash]. The chip selects the bucket number by itself.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://patch.msgid.link/20240827123938.582789-1-paweldembicki@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Using dev_err_cast_probe() to simplify the code.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Link: https://patch.msgid.link/20240828121805.3696631-1-lihongbo22@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GPIOF_DIR_* definitions are legacy and subject to remove.
Taking this into account, remove stale comment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240827171005.2301845-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski