Implement side MDIO channel support for LAN937x switches, providing an
alternative to SPI for PHY management alongside existing SPI-based
switch configuration. This is needed to reduce SPI load, as SPI can be
relatively expensive for small packets compared to MDIO support.
Also, implemented static mappings for PHY addresses for various LAN937x
models to support different internal PHY configurations. Since the PHY
address mappings are not equal to the port indexes, this patch also
provides PHY address calculation based on hardware strapping
configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace repeated cleanup code with a single error path using a label.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for accessing PHYs via a side MDIO interface in LAN937x
switches. The existing code already supports accessing PHYs via main
management interfaces, which can be SPI, I2C, or MDIO, depending on the
chip variant. This patch enables using a side MDIO bus, where SPI is
used for the main switch configuration and MDIO for managing the
integrated PHYs. On LAN937x, this is optional, allowing them to operate
in both configurations: SPI only, or SPI + MDIO. Typically, the SPI
interface is used for switch configuration, while MDIO handles PHY
management.
Additionally, update interrupt controller code to support non-linear
port to PHY address mapping, enabling correct interrupt handling for
configurations where PHY addresses do not directly correspond to port
indexes. This change ensures that the interrupt mechanism properly
aligns with the new, flexible PHY address mappings introduced by side
MDIO support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce port_setup_tc callback in mt7530 dsa driver in order to enable
dsa ports rate shaping via hw Token Bucket Filter (TBF) for hw switched
traffic.
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241031-mt7530-tc-offload-v2-1-cb242ad954a0@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These are the preferred way to copy ethtool strings.
Avoids incrementing pointers all over the place.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(for hellcreek driver)
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20241028044828.1639668-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'ports_fwnode' is initialized via device_get_named_child_node(), which
requires a call to fwnode_handle_put() when the variable is no longer
required to avoid leaking memory.
Add the missing fwnode_handle_put() after 'ports_fwnode' has been used
and is no longer required.
Fixes: 94a2a84f5e ("net: dsa: mv88e6xxx: Support LED control")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6393X family of devices can run its cycle counter off
an internal 250MHz clock instead of an external 125MHz one.
Add support for this cycle counter period by adding another set
of coefficients and lowering the periodic cycle counter read interval
to compensate for faster overflows at the increased frequency.
Otherwise, the PHC runs at 2x real time in userspace and cannot be
synchronized.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of relying on a fixed mapping of hardware family to cycle
counter frequency, pull this information from the
MV88E6XXX_TAI_CLOCK_PERIOD register.
This lets us support switches whose cycle counter frequencies depend on
board design.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of having them as individual fields in ptp_ops, wrap the
coefficients in a separate struct so they can be referenced together.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The well-known errata regarding EEE not being functional on various KSZ
switches has been refactored a few times. Recently the refactoring has
excluded several switches that the errata should also apply to.
Disable EEE for additional switches with this errata and provide
additional comments referring to the public errata document.
The original workaround for the errata was applied with a register
write to manually disable the EEE feature in MMD 7:60 which was being
applied for KSZ9477/KSZ9897/KSZ9567 switch ID's.
Then came commit 26dd2974c5 ("net: phy: micrel: Move KSZ9477 errata
fixes to PHY driver") and commit 6068e6d7ba ("net: dsa: microchip:
remove KSZ9477 PHY errata handling") which moved the errata from the
switch driver to the PHY driver but only for PHY_ID_KSZ9477 (PHY ID)
however that PHY code was dead code because an entry was never added
for PHY_ID_KSZ9477 via MODULE_DEVICE_TABLE.
This was apparently realized much later and commit 54a4e5c163 ("net:
phy: micrel: add Microchip KSZ 9477 to the device table") added the
PHY_ID_KSZ9477 to the PHY driver but as the errata was only being
applied to PHY_ID_KSZ9477 it's not completely clear what switches
that relates to.
Later commit 6149db4997 ("net: phy: micrel: fix KSZ9477 PHY issues
after suspend/resume") breaks this again for all but KSZ9897 by only
applying the errata for that PHY ID.
Following that this was affected with commit 08c6d8bae48c("net: phy:
Provide Module 4 KSZ9477 errata (DS80000754C)") which removes
the blatant register write to MMD 7:60 and replaces it by
setting phydev->eee_broken_modes = -1 so that the generic phy-c45 code
disables EEE but this is only done for the KSZ9477_CHIP_ID (Switch ID).
Lastly commit 0411f73c13 ("net: dsa: microchip: disable EEE for
KSZ8567/KSZ9567/KSZ9896/KSZ9897.") adds some additional switches
that were missing to the errata due to the previous changes.
This commit adds an additional set of switches.
Fixes: 0411f73c13 ("net: dsa: microchip: disable EEE for KSZ8567/KSZ9567/KSZ9896/KSZ9897.")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241018160658.781564-1-tharvey@gateworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cross-merge networking fixes after downstream PR (net-6.12-rc4).
Conflicts:
107a034d5c ("net/mlx5: qos: Store rate groups in a qos domain")
1da9cfd6c4 ("net/mlx5: Unregister notifier on eswitch init failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
mv88e6393x_port_set_policy doesn't correctly shift the ptr value when
converting the policy format between the old and new styles, so the
target register ends up with the ptr being written over the data bits.
Shift the pointer to align with the format expected by
mv88e6393x_port_policy_write().
Fixes: 6584b26020 ("net: dsa: mv88e6xxx: implement .port_set_policy for Amethyst")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241016040822.3917-1-peter@rashleigh.ca>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Rather than returning an EOPNOTSUPP error pointer when the switch
has no support for PCS, return NULL to indicate that no PCS is
required.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Similar to the situation described for sja1105 in commit 1f9fc48fd3
("net: dsa: sja1105: fix reception from VLAN-unaware bridges"), the
vsc73xx driver uses tag_8021q and doesn't need the ds->untag_bridge_pvid
request. In fact, this option breaks packet reception.
The ds->untag_bridge_pvid option strips VLANs from packets received on
VLAN-unaware bridge ports. But those VLANs should already be stripped
by tag_vsc73xx_8021q.c as part of vsc73xx_rcv() - they are not VLANs in
VLAN-unaware mode, but DSA tags. Thus, dsa_software_vlan_untag() tries
to untag a VLAN that doesn't exist, corrupting the packet.
Fixes: 93e4649efa ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20241014153041.1110364-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the Marvell datasheet the 88E6361 has two VTU pages
(4k VIDs per page) so the max_vid should be 8191, not 4095.
In the current implementation mv88e6xxx_vtu_walk() gives unexpected
results because of this error. I verified that mv88e6xxx_vtu_walk()
works correctly on the MV88E6361 with this patch in place.
Fixes: 12899f2998 ("net: dsa: mv88e6xxx: enable support for 88E6361 switch")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241014204342.5852-1-peter@rashleigh.ca
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prior to this patch ksz_ptp_msg_irq_setup() uses snprintf() to copy
strings. It does so by passing strings as the format argument of
snprintf(). This appears to be safe, due to the absence of format
specifiers in the strings, which are declared within the same function.
But nonetheless GCC 14 warns about it:
.../ksz_ptp.c:1109:55: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
1109 | snprintf(ptpmsg_irq->name, sizeof(ptpmsg_irq->name), name[n]);
| ^~~~~~~
.../ksz_ptp.c:1109:55: note: treat the string as an argument to avoid this
1109 | snprintf(ptpmsg_irq->name, sizeof(ptpmsg_irq->name), name[n]);
| ^
| "%s",
As what we are really dealing with here is a string copy, it seems make
sense to use a function designed for this purpose. In this case null
padding is not required, so strscpy is appropriate. And as the
destination is an array of fixed size, the 2-argument variant may be used.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241014-string-thing-v2-1-b9b29625060a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The err value in mv88e6xxx_region_atu_snapshot is now potentially
uninitialised on return. Initialise err as 0.
Fixes: ada5c3229b ("net: dsa: mv88e6xxx: Add FID map cache")
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241009212319.1045176-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a cached FID bitmap. This mitigates the need to walk all VTU entries
to find the next free FID.
When flushing the VTU (during init), zero the FID bitmap. Use and
manipulate this bitmap from now on, instead of reading HW for the FID
map.
The repeated VTU walks are costly and can take ~40 mins if ~4000 vlans
are added. Caching the FID map reduces this time to <2 mins.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241006212905.3142976-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All modern chips support and need the 10_100 bit set for supporting jumbo
frames on 10/100 ports, so instead of enabling it only for 583XX enable
it for everything except bcm63xx, where the bit is writeable, but does
nothing.
Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds
without the bit set.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
While BCM5325/5365 do not support jumbo frames, they do support slightly
oversized frames, so do not error out if requesting a supported MTU for
them.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
BCM5325/BCM5365 do not support jumbo frames, so we should not report a
jumbo frame mtu for them. But they do support so called "oversized"
frames up to 1536 bytes long by default, so report an appropriate MTU.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Accessing device registers seems to be not reliable, the chip
revision is sometimes detected wrongly (0 instead of expected 1).
Ensure that the chip reset is performed via reset GPIO and then
wait for 'Device Ready' status in HW_CFG register before doing
any register initializations.
Cc: stable@vger.kernel.org
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
[alex: reworked using read_poll_timeout()]
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20241004113655.3436296-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/dsa to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/36da477cb9fa0bffec32d50c2cf3d18e94a0e7e3.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SF2 crossbar register is a packed bitfield, giving the index of the
external port selected for each of the internal ports. On BCM4908 (the
only currently-supported switch family with a crossbar), there are 2
internal ports and 3 external ports, so there are 2 bits per internal
port.
The driver currently conflates the "bits per port" and "number of ports"
concepts, lumping both into the `num_crossbar_int_ports` field. Since it
is currently only possible for either of these counts to have a value of
2, there is no behavioral error resulting from this situation for now.
Make the code more readable (and support the future possibility of
larger crossbars) by adding a `num_crossbar_ext_bits` field to represent
the "bits per port" count and relying on this where appropriate instead.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241003212301.1339647-1-CFSworks@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds control over the hardware LEDs in the Marvell
MV88E6xxx DSA switch and enables it for MV88E6352.
This fixes an imminent problem on the Inteno XG6846 which
has a WAN LED that simply do not work with hardware
defaults: driver amendment is necessary.
The patch is modeled after Christian Marangis LED support
code for the QCA8k DSA switch, I got help with the register
definitions from Tim Harvey.
After this patch it is possible to activate hardware link
indication like this (or with a similar script):
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link
This makes the green link indicator come up on any link
speed. It is also possible to be more elaborate, like this:
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link_1000
cd /sys/class/leds/Marvell\ 88E6352:05:01:amber:wan/
echo netdev > trigger
echo 1 > link_100
Making the green LED come on for a gigabit link and the
amber LED come on for a 100 mbit link.
Each port has 2 LED slots (the hardware may use just one or
none) and the hardware triggers are specified in four bits per
LED, and some of the hardware triggers are only available on the
SFP (fiber) uplink. The restrictions are described in the
port.h header file where the registers are described. For
example, selector 1 set for LED 1 on port 5 or 6 will indicate
Fiber 1000 (gigabit) and activity with a blinking LED, but
ONLY for an SFP connection. If port 5/6 is used with something
not SFP, this selector is a noop: something else need to be
selected.
After the previous series rewriting the MV88E6xxx DT
bindings to use YAML a "leds" subnode is already valid
for each port, in my scratch device tree it looks like
this:
leds {
#address-cells = <1>;
#size-cells = <0>;
led@0 {
reg = <0>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_LAN;
default-state = "off";
linux,default-trigger = "netdev";
};
led@1 {
reg = <1>;
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_LAN;
default-state = "off";
};
};
This DT config is not yet configuring everything: when the netdev
default trigger is assigned the hw acceleration callbacks are
not called, and there is no way to set the netdev sub-trigger
type (such as link_1000) from the device tree, such as if you want
a gigabit link indicator. This has to be done from userspace at
this point.
We add LED operations to all switches in the 6352 family:
6172, 6176, 6240 and 6352.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241001-mv88e6xxx-leds-v4-1-cc11c4f49b18@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit introduced an unexpected regression in the sja1105
driver. Packets from VLAN-unaware bridge ports get received correctly,
but the protocol stack can't seem to decode them properly.
For ds->untag_bridge_pvid users (thus also sja1105), the blamed commit
did introduce a functional change: dsa_switch_rcv() used to call
dsa_untag_bridge_pvid(), which looked like this:
err = br_vlan_get_proto(br, &proto);
if (err)
return skb;
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb) && skb->protocol == htons(proto)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
and now it calls dsa_software_vlan_untag() which has just this:
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
thus lacks any skb->protocol == bridge VLAN protocol check. That check
is deferred until a later check for skb->vlan_proto (in the hwaccel area).
The new code is problematic because, for VLAN-untagged packets,
skb_vlan_untag() blindly takes the 4 bytes starting with the EtherType
and turns them into a hwaccel VLAN tag. This is what breaks the protocol
stack.
It would be tempting to "make it work as before" and only call
skb_vlan_untag() for those packets with the skb->protocol actually
representing a VLAN.
But the premise of the newly introduced dsa_software_vlan_untag() core
function is not wrong. Drivers set ds->untag_bridge_pvid or
ds->untag_vlan_aware_bridge_pvid presumably because they send all
traffic to the CPU reception path as VLAN-tagged. So why should we spend
any additional CPU cycles assuming that the packet may be VLAN-untagged?
And why does the sja1105 driver opt into ds->untag_bridge_pvid if it
doesn't always deliver packets to the CPU as VLAN-tagged?
The answer to the latter question is indeed more interesting: it doesn't
need to. This got done in commit 884be12f85 ("net: dsa: sja1105: add
support for imprecise RX"), because I thought it would be needed, but I
didn't realize that it doesn't actually make a difference.
As explained in the commit message of the blamed patch, ds->untag_bridge_pvid
only makes a difference in the VLAN-untagged receive path of a bridge port.
However, in that operating mode, tag_sja1105.c makes use of VLAN tags
with the ETH_P_SJA1105 TPID, and it decodes and consumes these VLAN tags
as if they were DSA tags (aka tag_8021q operation). Even if commit
884be12f85 ("net: dsa: sja1105: add support for imprecise RX") added
this logic in sja1105_bridge_vlan_add():
/* Always install bridge VLANs as egress-tagged on the CPU port. */
if (dsa_is_cpu_port(ds, port))
flags = 0;
that was for _bridge_ VLANs, which are _not_ committed to hardware
in VLAN-unaware mode (aka the mode where ds->untag_bridge_pvid does
anything at all). Even prior to that change, the tag_8021q VLANs
were always installed as egress-tagged on the CPU port, see
dsa_switch_tag_8021q_vlan_add():
u16 flags = 0; // egress-tagged, non-PVID
if (dsa_port_is_user(dp))
flags |= BRIDGE_VLAN_INFO_UNTAGGED |
BRIDGE_VLAN_INFO_PVID;
err = dsa_port_do_tag_8021q_vlan_add(dp, info->vid,
flags);
if (err)
return err;
Whether the sja1105 driver needs the new flag, ds->untag_vlan_aware_bridge_pvid,
rather than ds->untag_bridge_pvid, is a separate discussion. To fix the
current bug in VLAN-unaware bridge mode, I would argue that the sja1105
driver should not request something it doesn't need, rather than
complicating the core DSA helper. Whereas before the blamed commit, this
setting was harmless, now it has caused breakage.
Fixes: 93e4649efa ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241001140206.50933-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use xpcs_create_pcs_mdiodev() to create the XPCS instance, storing
and using the phylink_pcs pointer internally, rather than dw_xpcs.
Use xpcs_destroy_pcs() to destroy the XPCS instance when we've
finished with it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMk-005ZIj-R3@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call the PCS operations through the ops structure, which avoids needing
to export xpcs internal functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMf-005ZId-Mx@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The static configuration reload saves the port speed in the static
configuration tables by first converting it from the internal
respresentation to the SPEED_xxx ethtool representation, and then
converts it back to restore the setting. This is because
sja1105_adjust_port_config() takes the speed as SPEED_xxx.
However, this is unnecessarily complex. If we split
sja1105_adjust_port_config() up, we can simply save and restore the
mac[port].speed member in the static configuration tables.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMa-005ZIX-If@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Cross-merge networking fixes after downstream PR.
No conflicts (sort of) and no adjacent changes.
This merge reverts commit b3c9e65eb2 ("net: hsr: remove seqnr_lock")
from net, as it was superseded by
commit 430d67bdcb ("net: hsr: Use the seqnr lock for frames received via interlink port.")
in net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TAS module could not be configured when it's running in pending
status. We need disable the module and configure it again. However, the
pending status is not cleared after the module disabled. TC taprio set
will always return busy even it's disabled.
For example, a user uses tc-taprio to configure Qbv and a future
basetime. The TAS module will run in a pending status. There is no way
to reconfigure Qbv, it always returns busy.
Actually the TAS module can be reconfigured when it's disabled. So it
doesn't need to check the pending status if the TAS module is disabled.
After the patch, user can delete the tc taprio configuration to disable
Qbv and reconfigure it again.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Link: https://patch.msgid.link/20240906093550.29985-1-xiaoliang.yang_1@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace ksz8830 with ksz88x3 for CHIP_ID definition and other
strings. This due to KSZ8830 not being an actual switch but the Chip
ID shared among KSZ8863/8873 switches, impossible to differentiate
from their Chip ID or Revision ID registers.
Now all KSZ*_CHIP_ID macros refer to actual, existing switches which
removes confusion.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove macros that are already defined at more appropriate places.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first KSZ8 series implementation was done for a KSZ8795 device but
since several other KSZ8 devices have been added. Rename these files
to adhere to the ksz8 naming convention as already used in most
functions and the existing ksz8.h; add an explanatory note.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the __counted_by compiler attribute to the flexible array member
entries to improve access bounds-checking via CONFIG_UBSAN_BOUNDS and
CONFIG_FORTIFY_SOURCE.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://patch.msgid.link/20240904014956.2035117-1-lihongbo22@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Avoids the need for manual cleanup of_node_put() in early exits
from the loop by using for_each_available_child_of_node_scoped().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Avoid need to manually handle of_node_put() by using
for_each_child_of_node_scoped(), which can simplfy code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This commit introduces implementations of three functions:
.port_fdb_dump
.port_fdb_add
.port_fdb_del
The FDB database organization is the same as in other old Vitesse chips:
It has 2048 rows and 4 columns (buckets). The row index is calculated by
the hash function 'vsc73xx_calc_hash' and the FDB entry must be placed
exactly into row[hash]. The chip selects the bucket number by itself.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://patch.msgid.link/20240827123938.582789-1-paweldembicki@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Using dev_err_cast_probe() to simplify the code.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Link: https://patch.msgid.link/20240828121805.3696631-1-lihongbo22@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GPIOF_DIR_* definitions are legacy and subject to remove.
Taking this into account, remove stale comment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240827171005.2301845-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KSZ8895/KSZ8864 is a switch family between KSZ8863/73 and KSZ8795, so it
shares some registers and functions in those switches already
implemented in the KSZ DSA driver.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Tested-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt.h
c948c0973d ("bnxt_en: Don't clear ntuple filters and rss contexts during ethtool ops")
f2878cdeb7 ("bnxt_en: Add support to call FW to update a VNIC")
Link: https://patch.msgid.link/20240822210125.1542769-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240820075047.681223-1-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240820074805.680674-1-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If an ATU violation was caused by a CPU Load operation, the SPID could
be larger than DSA_MAX_PORTS (the size of mv88e6xxx_chip.ports[] array).
Fixes: 75c05a74e7 ("net: dsa: mv88e6xxx: Fix counting of ATU violations")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240819235251.1331763-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing the port_hwtstamp_set operation, ptp_schedule_worker()
will be called if hardware timestamoing is enabled on any of the ports.
When using multiple ports for PTP, port_hwtstamp_set is executed for
each port. When called for the first time ptp_schedule_worker() returns
0. On subsequent calls it returns 1, indicating the worker is already
scheduled. Currently the ksz driver treats 1 as an error and fails to
complete the port_hwtstamp_set operation, thus leaving the timestamping
configuration for those ports unchanged.
This patch fixes this by ignoring the ptp_schedule_worker() return
value.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/7aae307a-35ca-4209-a850-7b2749d40f90@martin-whitaker.me.uk
Fixes: bb01ad3057 ("net: dsa: microchip: ptp: manipulating absolute time using ptp hw clock")
Signed-off-by: Martin Whitaker <foss@martin-whitaker.me.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240817094141.3332-1-foss@martin-whitaker.me.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ87xx switches have 32 static MAC address table entries and not
8. This fixes -ENOSPC non-critical errors from ksz8_add_sta_mac when
configured as a bridge.
Add a new ksz87xx_dev_ops structure to be able to use the
ksz_r_mib_stat64 pointer for this family; this corrects a wrong
mib->counters cast to ksz88xx_stats_raw. This fixes iproute2
statistics. Rename ksz8_dev_ops structure to ksz88x3_dev_ops, in line
with ksz_is_* naming conventions from ksz_common.h.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-6-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add WoL support for KSZ87xx family of switches. This code was tested
with a KSZ8794 chip.
Implement ksz_common usage of the new device-tree property
'microchip,pme-active-high'.
Make use of the now generalized ksz_common WoL functions, adding an
additional interrupt register write for KSZ87xx. Add helper functions
to convert from PME (port) read/writes to indirect register
read/writes in the dedicated ksz8795 sources. Add initial
configuration during (port) setup as per KSZ9477.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-5-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Generalize KSZ9477 WoL functions at ksz_common. Move dedicated registers
and generic masks to existing structures & defines for that purpose.
Introduction of PME (port) read/write helper functions, which happen
to be the generic read/write for KSZ9477 but not for the incoming
KSZ87xx patch.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-4-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move KSZ9477 WoL functions to ksz_common, in preparation for adding
KSZ87xx family support.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-3-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a major design bug with ocelot-8021q, which is that it expects
more of the hardware than the hardware can actually do. The short
summary of the issue is that when a port is under a VLAN-aware bridge
and we use this tagging protocol, VLAN upper interfaces of this port do
not see RX traffic.
We use VCAP ES0 (egress rewriter) rules towards the tag_8021q CPU port
to encapsulate packets with an outer tag, later stripped by software,
that depends on the source user port. We do this so that packets can be
identified in ocelot_rcv(). To be precise, we create rules with
push_outer_tag = OCELOT_ES0_TAG and push_inner_tag = 0.
With this configuration, we expect the switch to keep the inner tag
configuration as found in the packet (if it was untagged on user port
ingress, keep it untagged, otherwise preserve the VLAN tag unmodified
as the inner tag towards the tag_8021q CPU port). But this is not what
happens.
Instead, table "Tagging Combinations" from the user manual suggests
that when the ES0 action is "PUSH_OUTER_TAG=1 and PUSH_INNER_TAG=0",
there will be "no inner tag". Experimentation further clarifies what
this means.
It appears that this "inner tag" which is not pushed into the packet on
its egress towards the CPU is none other than the classified VLAN.
When the ingress user port is standalone or under a VLAN-unaware bridge,
the classified VLAN is a discardable quantity: it is a fixed value - the
result of ocelot_vlan_unaware_pvid()'s configuration, and actually
independent of the VID from any 802.1Q header that may be in the frame.
It is actually preferable to discard the "inner tag" in this case.
The problem is when the ingress port is under a VLAN-aware bridge.
Then, the classified VLAN is taken from the frame's 802.1Q header, with
a fallback on the bridge port's PVID. It would be very good to not
discard the "inner tag" here, because if we do, we break communication
with any 8021q VLAN uppers that the port might have. These have a
processing path outside the bridge.
There seems to be nothing else we can do except to change the
configuration for VCAP ES0 rules, to actually push the inner VLAN into
the frame. There are 2 options for that, first is to push a fixed value
specified in the rule, and second is to push a fixed value, plus
(aka arithmetic +) the classified VLAN. We choose the second option,
and we select that fixed value as 0. Thus, what is pushed in the inner
tag is just the classified VLAN.
From there, we need to perform software untagging, in the receive path,
of stuff that was untagged on the wire.
Fixes: 7c83a7c539 ("net: dsa: add a second tagger for Ocelot switches based on tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained by Horatiu Vultur in commit 603ead9658 ("net: sparx5: Add
spinlock for frame transmission from CPU") which is for a similar
hardware design, multiple CPUs can simultaneously perform injection
or extraction. There are only 2 register groups for injection and 2
for extraction, and the driver only uses one of each. So we'd better
serialize access using spin locks, otherwise frame corruption is
possible.
Note that unlike in sparx5, FDMA in ocelot does not have this issue
because struct ocelot_fdma_tx_ring already contains an xmit_lock.
I guess this is mostly a problem for NXP LS1028A, as that is dual core.
I don't think VSC7514 is. So I'm blaming the commit where LS1028A (aka
the felix DSA driver) started using register-based packet injection and
extraction.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the URL in a single line for easier copy-pasting.
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240812124346.597702-1-enguerrand.de-ribaucourt@savoirfairelinux.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Resetting the VSC73xx PHY was problematic because the MDIO bus, without
a busy check, read and wrote incorrect register values.
My investigation indicates that resetting the PHY only triggers changes
in configuration. However, improper register values written earlier
were only exposed after a soft reset.
The reset itself wasn't the issue; rather, the problem stemmed from
incorrect read and write operations.
A 'soft_reset' can now proceed normally. There are no reasons to keep
the VSC73xx from being reset.
This commit removes the reset blockade in the 'vsc73xx_phy_write'
function.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC73xx has a busy flag used during MDIO operations. It is raised
when MDIO read/write operations are in progress. Without it, PHYs are
misconfigured and bus operations do not work as expected.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the 'vsc73xx_phy_write' function, the register value is missing,
and the phy write operation always sends zeros.
This commit passes the value variable into the proper register.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the datasheet description ("Port Mode Procedure" in 5.6.2),
the VSC73XX_MAC_CFG_WEXC_DIS bit is configured only for half duplex mode.
The WEXC_DIS bit is responsible for MAC behavior after an excessive
collision. Let's set it as described in the datasheet.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to respect the 80 columns limit, split the half-duplex
monitoring function in two.
This is just a styling change, no functional change.
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit changes magic numbers in phy operations.
Some shifted registers was replaced with bitfield macros.
No functional changes done.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2_mdio_register() calls of_phy_find_device() and then
phy_device_remove() in a loop to remove existing PHY devices.
of_phy_find_device() eventually calls bus_find_device(), which calls
get_device() on the returned struct device * to increment the refcount.
The current implementation does not decrement the refcount, which causes
memory leak.
This commit adds the missing phy_device_free() call to decrement the
refcount via put_device() to balance the refcount.
Fixes: 771089c2a4 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240806011327.3817861-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The wol variable in ksz_port_set_mac_address() is declared with random
data, but the code in ksz_get_wol call may not be executed so the
WAKE_MAGIC check may be invalid resulting in an error message when
setting a MAC address after starting the DSA driver.
Fixes: 3b454b6390 ("net: dsa: microchip: ksz9477: Add Wake on Magic Packet support")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240805235200.24982-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce support for the DSA built-in switch available on the EN7581
development board. EN7581 support is similar to MT7988 one except
it requires to set MT7530_FORCE_MODE bit in MT753X_PMCR_P register
for on cpu port.
Tested-by: Benjamin Larsson <benjamin.larsson@genexis.eu>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the datasheet, the VSC73xx family's maximum internal MDIO bus
speed is 20 MHz. It also allows disabling the preamble.
This commit sets the MDIO clock prescaler to the minimum value and
disables the preamble to speed up MDIO operations.
It doesn't affect the external bus because it's configured in a different
subblock.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240731203455.580262-1-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch switches hardcoded RGMII transmit/receive delay to
a configurable value. Delay values are taken from the properties of
the CPU port: 'tx-internal-delay-ps' and 'rx-internal-delay-ps'.
The default value is configured to 2.0 ns to maintain backward
compatibility with existing code.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom switches supported by the b53 driver use a chip-wide jumbo frame
configuration. In the commit referenced with the Fixes tag, the setting
is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient chip-wide maximum frame size for the CPU port.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports. This aligns the driver
to the behavior of other switch drivers.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Marvell chips not supporting per-port jumbo frame size configurations use
a chip-wide frame size configuration. In the commit referenced with the
Fixes tag, the setting is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient maximum frame size for the CPU port. Specifically, sending
full-size frames from the CPU port on a MV88E6097 having a user port MTU
of 1500 bytes results in dropped frames.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch implements .port_pre_bridge_flags() and .port_bridge_flags(),
which are required for properly treating the BR_LEARNING flag. Also,
.port_stp_state_set() is tweaked and now disables learning for standalone
ports.
Disabling learning for standalone ports is required to avoid situations
where one port sees traffic originating from another, which could cause
packet drops.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-13-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds bridge support for the vsc73xx driver.
The vsc73xx requires minimal operations and ithe generic
dsa_tag_8021q_bridge_* API is sufficient.
The forwarding matrix is managed by vsc73xx_port_stp_state_set() ->
vsc73xx_refresh_fwd_map()i routine, which is called immediately after
.port_bridge_join() and .port_bridge_leave().
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-12-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'dsa_tag_8021q_bridge_join' could be used as a generic implementation
of the 'ds->ops->port_bridge_join()' function. However, it is necessary
to synchronize their arguments.
This patch also moves the 'tx_fwd_offload' flag configuration line into
'dsa_tag_8021q_bridge_join' body. Currently, every (sja1105) driver sets
it, and the future vsc73xx implementation will also need it for
simplification.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-11-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Max number of bridges in tag8021q implementation is strictly limited
by VBID size: 3 bits. But zero is reserved and only 7 values can be used.
This patch adds define which describe maximum possible value.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-10-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is a simple implementation of 802.1q tagging in the vsc73xx
driver. Currently, devices with DSA_TAG_PROTO_NONE are not functional.
The VSC73XX family doesn't provide any tag support for external Ethernet
ports.
The only option available is VLAN-based tagging, which requires constant
hardware VLAN filtering. While the VSC73XX family supports provider
bridging, it only supports QinQ without full implementation of 802.1AD.
This means it only allows the doubled 0x8100 TPID.
In the simple port mode, QinQ is enabled to preserve forwarding of
VLAN-tagged frames.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-9-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch implements VLAN filtering for the vsc73xx driver.
After starting VLAN filtering, the switch is reconfigured from QinQ to
a simple VLAN aware mode. This is required because VSC73XX chips do not
support inner VLAN tag filtering.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-3-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This isn't a fully functional implementation of 802.1D, but
port_stp_state_set is required for a future tag8021q operations.
This implementation handles properly all states, but vsc73xx doesn't
forward STP packets.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-2-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/act_ct.c
26488172b0 ("net/sched: Fix UAF when resolving a clash")
3abbd7ed8b ("act_ct: prepare for stolen verdict coming from conntrack and nat engine")
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set proper MAC capabilities for port 4 on LAN9371 and LAN9372 switches with
integrated 100BaseTX PHY. And introduce the is_lan937x_tx_phy() function to
reuse it where applicable.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`ar9331_sw_bus` is not modified and can be declared as const to
move its data to a read-only section.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240703-net-const-regmap-v1-4-ff4aeceda02c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
`qca8k_regmap_config` is not modified and can be declared as const to
move its data to a read-only section.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240703-net-const-regmap-v1-1-ff4aeceda02c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'phy' parameter supplied to lan9303_phy_read/_write was sometimes a
DSA port number and sometimes a PHY address. This isn't a problem as
long as they are equal. But if the external phy_addr_sel_strap pin is
wired to 'high', the PHY addresses change from 0-1-2 to 1-2-3 (CPU,
slave0, slave1). In this case, lan9303_phy_read/_write must translate
between DSA port numbers and the corresponding PHY address.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240703145718.19951-1-ceggers@arri.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce error handling for lan937x_cfg function calls in lan937x_setup.
This change ensures that if any lan937x_cfg or ksz_rmw32 calls fails, the
function will return the appropriate error code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240703083820.3152100-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As described by the microchip article "LAN937X - The required
configuration for the external MAC port to operate at RGMII-to-RGMII
1Gbps link speed." [1]:
"When VPHY is enabled, the auto-negotiation process following IEEE 802.3
standard will be triggered and will result in RGMII-to-RGMII signal
failure on the interface because VPHY will try to poll the PHY status
that is not available in the scenario of RGMII-to-RGMII connection
(normally the link partner is usually an external processor).
Note that when VPHY fails on accessing PHY registers, it will fall back
to 100Mbps speed, it indicates disabling VPHY is optional if you only
need the port to link at 100Mbps speed.
Again, VPHY must and can only be disabled by writing VPHY_DISABLE bit in
the register below as there is no strapping pin for the control."
This patch was tested on LAN9372, so far it seems to not to affect VPHY
based clock crossing optimization for the ports with integrated PHYs.
[1]: https://microchip.my.site.com/s/article/LAN937X-The-required-configuration-for-the-external-MAC-port-to-operate-at-RGMII-to-RGMII-1Gbps-link-speed
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver do not support in-band mode and in case of CPU<->Switch
link, this mode is not working any way. So, disable it otherwise ingress
path of the switch MAC will stay disabled.
Note: lan9372 manual do not document 0xN301 BIT(2) for the RGMII mode
and recommend[1] to disable in-band link status update for the RGMII RX
path by clearing 0xN302 BIT(0). But, 0xN301 BIT(2) seems to work too, so
keep it unified with other KSZ switches.
[1] https://microchip.my.site.com/s/article/LAN937X-The-required-configuration-for-the-external-MAC-port-to-operate-at-RGMII-to-RGMII-1Gbps-link-speed
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the LAN9371 and LAN9372, the 4th internal PHY is a 100BaseTX PHY
instead of a 100BaseT1 PHY. The 100BaseTX PHYs have a different base
register offset.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
e3f02f32a0 ("ionic: fix kernel panic due to multi-buffer handling")
d9c0420999 ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For mlxsw
Reviewed-by: Kory Maincent <Kory.maincent@bootlin.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au> # for mctp-i2c
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20240625083853.2205977-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch global port interrupt mask, REG_SW_PORT_INT_MASK__4, is
defined as 0x001C in ksz9477_reg.h. The designers used 32-bit value in
anticipation for increase of port count in future product but currently
the maximum port count is 7 and the effective value is 0x7F in register
0x001F. Each port has its own interrupt mask and is defined as 0x#01F.
It uses only 4 bits for different interrupts.
The developer who implemented the current interrupt mechanism in the
switch driver noticed there are similarities between the mechanism to
mask port interrupts in global interrupt and individual interrupts in
each port and so used the same code to handle these interrupts. He
updated the code to use the new macro REG_SW_PORT_INT_MASK__1 which is
defined as 0x1F in ksz_common.h but he forgot to update the 32-bit write
to 8-bit as now the mask registers are 0x1F and 0x#01F.
In addition all KSZ switches other than the KSZ9897/KSZ9893 and LAN937X
families use only 8-bit access and so this common code will eventually
be changed to accommodate them.
Fixes: e1add7dd61 ("net: dsa: microchip: use common irq routines for girq and pirq")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://lore.kernel.org/r/1719009262-2948-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The errata DS80000754 recommends monitoring potential faults in
half-duplex mode for the KSZ9477 family.
half-duplex is not very common so I just added a critical message
when the fault conditions are detected. The switch can be expected
to be unable to communicate anymore in these states and a software
reset of the switch would be required which I did not implement.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errata DS80000758 states that carrier sense back pressure mode can cause
link down issues in 100BASE-TX half duplex mode. The datasheet also
recommends to always use the collision based back pressure mode.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Woojung Huh <Woojung.huh@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a pair of ports from the port matrix when both ports have the
isolated flag set.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the logic in qca8k_port_bridge_join() and qca8k_port_bridge_leave()
is the same. Refactor to reduce duplication and prepare for reusing the
code for implementing bridge port isolation.
dsa_port_offloads_bridge_dev() is used instead of
dsa_port_offloads_bridge(), passing the bridge in as a struct netdevice *,
as we won't have a struct dsa_bridge in qca8k_port_bridge_flags().
The error handling is changed slightly in the bridge leave case,
returning early and emitting an error message when a regmap access fails.
This shouldn't matter in practice, as there isn't much we can do if
communication with the switch breaks down in the middle of reconfiguration.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k_port_bridge_join() set QCA8K_PORT_LOOKUP_CTRL() for i == port twice,
once in the loop handling all other port's masks, and finally at the end
with the accumulated port_mask.
The first time it would incorrectly set the port's own bit in the mask,
only to correct the mistake a moment later. qca8k_port_bridge_leave() had
the same issue, but here the regmap_clear_bits() was a no-op rather than
setting an unintended value.
Remove the duplicate assignment by skipping the whole loop iteration for
i == port. The unintended bit setting doesn't seem to have any negative
effects (even when not reverted right away), so the change is submitted
as a simple cleanup rather than a fix.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 allows HSR in-HW offloading for any of two selected ports.
This patch adds check if one tries to use more than two ports with
HSR offloading enabled.
The problem is with RedBox configuration (HSR-SAN) - when configuring:
ip link add name hsr0 type hsr slave1 lan1 slave2 lan2 interlink lan3 \
supervision 45 version 1
The lan1 (port0) and lan2 (port1) are correctly configured as ports, which
can use HSR offloading on ksz9477.
However, when we do already have two bits set in hsr_ports, we need to
return (-ENOTSUPP), so the interlink port (lan3) would be used with
SW based HSR RedBox support.
Otherwise, I do see some strange network behavior, as some HSR frames are
visible on non-HSR network and vice versa.
This causes the switch connected to interlink port (lan3) to drop frames
and no communication is possible.
Moreover, conceptually - the interlink (i.e. HSR-SAN port - lan3/port2)
shall be only supported in software as it is also possible to use ksz9477
with only SW based HSR (i.e. port0/1 -> hsr0 with offloading, port2 ->
HSR-SAN/interlink, port4/5 -> hsr1 with SW based HSR).
Fixes: 5055cccfc2 ("net: hsr: Provide RedBox support (HSR-SAN)")
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The very first flush in any port will flush all learned addresses in all
ports. This can be observed by unplugging the cable from one port while
additional ports are connected and dumping the fdb entries.
This problem is caused by the initially wrong value programmed to the
REG_SW_LUE_CTRL_1 register. Setting SW_FLUSH_STP_TABLE and
SW_FLUSH_MSTP_TABLE bits does not have an immediate effect. It is when
ksz9477_flush_dyn_mac_table() is called then the SW_FLUSH_STP_TABLE bit
takes effect and flushes all learned entries. After that call both bits
are reset and so the next port flush will not cause such problem again.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/1718756202-2731-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove a pair of ports from the port matrix when both ports have the
isolated flag set.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As preparation for implementing bridge port isolation, move the logic to
add and remove bits in the port matrix into a new helper
mt7530_update_port_member(), which is called from
mt7530_port_bridge_join() and mt7530_port_bridge_leave().
Another part of the preparation is using dsa_port_offloads_bridge_dev()
instead of dsa_port_offloads_bridge() to check for bridge membership, as
we don't have a struct dsa_bridge in mt7530_port_bridge_flags().
The port matrix setting is slightly streamlined, now always first setting
the mt7530_port's pm field and then writing the port matrix from that
field into the hardware register, instead of duplicating the bit
manipulation for both the struct field and the register.
mt7530_port_bridge_join() was previously using |= to update the port
matrix with the port bitmap, which was unnecessary, as pm would only
have the CPU port set before joining a bridge; a simple assignment can
be used for both joining and leaving (and will also work when individual
bits are added/removed in port_bitmap with regard to the previous port
matrix, which is what happens with port isolation).
No functional change intended.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print that no FID is found for bridge %s instead of the incorrect
message that the port is not part of a bridge.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-13-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the comments in gswip_port_vlan_filtering() so it's clear that
there are two separate cases, one for "tag based VLAN" and another one
for "port based VLAN".
Suggested-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-12-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The port validation in gswip_add_single_port_br() is superfluous and
can be omitted.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240611135434.3180973-11-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Only bits [5:0] in mac_bridge.key[3] are reserved for the FID.
Also, for dynamic (learned) entries, bits [7:4] in mac_bridge.val[0]
represents the port.
Introduce new macros GSWIP_TABLE_MAC_BRIDGE_KEY3_FID and
GSWIP_TABLE_MAC_BRIDGE_VAL0_PORT macro and use it throughout the driver.
Also rename and update GSWIP_TABLE_MAC_BRIDGE_VAL1_STATIC to use the
BIT() macro. This makes the driver code easier to understand.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240611135434.3180973-10-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The addr variable in gswip_port_fdb_dump() stores a mac address. Use
ETH_ALEN to make this consistent across other drivers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-9-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make the check for the CPU port in gswip_port_change_mtu() consistent
with other areas of the driver by using dsa_is_cpu_port().
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-8-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before commit 74be4babe7 ("net: dsa: do not enable or disable non user
ports"), gswip_port_enable/disable() were also executed for the cpu port
in gswip_setup() which disabled the cpu port during initialization.
Let's restore this by removing the dsa_is_user_port checks. Also, let's
clean up the gswip_port_enable() function so that we only have to check
for the cpu port once. The operation reordering done here is safe.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240611135434.3180973-7-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We don't need to manually call gswip_port_enable() from within
gswip_setup() for the CPU port. DSA does this automatically for us.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-6-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_err_probe() can be used to simplify the existing code. Also it means
we get rid of the following warning which is seen whenever the PMAC
(Ethernet controller which connects to GSWIP's CPU port) has not been
probed yet:
gswip 1e108000.switch: dsa switch register failed: -517
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-5-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some dev_err are missing the terminating \n. Let's add that.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240611135434.3180973-4-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the CPU port to gswip_xrx200_phylink_get_caps() and
gswip_xrx300_phylink_get_caps(). It connects through a SoC-internal bus,
so the only allowed phy-mode is PHY_INTERFACE_MODE_INTERNAL.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-3-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kernel.h is included solely for some other existing headers.
Include them directly and get rid of kernel.h.
While at it, sort headers alphabetically for easier maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation for device_get_named_child_node() mentions this
important point:
"
The caller is responsible for calling fwnode_handle_put() on the
returned fwnode pointer.
"
Add fwnode_handle_put() to avoid leaked references.
Fixes: 1e264f9d29 ("net: dsa: qca8k: add LEDs basic support")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the common felix_register_switch() from the umbrella driver
is the only entity that accesses these data structures, we can remove
them from the list of the exported symbols.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init code, which could be
made common [1].
[1]: https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Here, we take the following common steps:
- "felix" and "ds" structure allocation
- "felix", "ocelot" and "ds" basic structure initialization
- dsa_register_switch() call
and we make a common function out of them.
For every driver except felix_vsc9959, this is also the entire probing
procedure. For felix_vsc9959, we also need to do some PCI-specific
stuff, which can easily be reordered to be done before, and unwound on
failure.
We also have to convert the bus-specific platform_set_drvdata() and
pci_set_drvdata() calls into dev_set_drvdata(). But this should have no
impact on the behavior.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King points out that seville_vsc9953 populates
felix->info->num_tx_queues = 8, but this doesn't make it all the way
into ds->num_tx_queues (which is how the user interface netdev queues
get allocated) [1].
[1]: https://lore.kernel.org/all/20240415160150.yejcazpjqvn7vhxu@skbuf/
When num_tx_queues=0 for seville, this is implicitly converted to 1 by
dsa_user_create(), and this is good enough for basic operation for a
switch port. The tc qdisc offload layer works with netdev TX queues,
so for QoS offload we need to pretend we have multiple TX queues. The
VSC9953, like ocelot_ext, doesn't export QoS offload, so it doesn't
really matter. But we can definitely set num_tx_queues=8 for all
switches.
The felix->info->num_tx_queues construct itself seems unnecessary.
It was introduced by commit de143c0e27 ("net: dsa: felix: Configure
Time-Aware Scheduler via taprio offload") at a time when vsc9959
(LS1028A) was the only switch supported by the driver.
8 traffic classes, and 1 queue per traffic class, is a common
architectural feature of all switches in the family. So they could
all just set OCELOT_NUM_TC and be fine.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current placement of devm_request_threaded_irq() is inconvenient.
It is between the allocation of the "felix" structure and
dsa_register_switch(), both of which we'd like to refactor into a
function that's common for all switches. But the IRQ is specific to
felix_vsc9959.
A closer inspection of the felix_irq_handler() code suggests that
it does things that depend on the data structures having been fully
initialized. For example, ocelot_get_txtstamp() takes
&port->tx_skbs.lock, which has only been initialized in
ocelot_init_port() which has not run yet.
It is not one of those IRQF_SHARED IRQs, so CONFIG_DEBUG_SHIRQ_FIXME
shouldn't apply here, and thus, it doesn't really matter, because in
practice, the IRQ will not be triggered so early. Nonetheless, it is a
good practice for the driver to be prepared for it to fire as soon as it
is requested.
Create a new felix->info method for running custom code for vsc9959 from
within felix_setup(), and move the request_irq() call there. The
ocelot_ext should have an IRQ as well, so this should be a step in the
right direction for that model (VSC7512) as well.
Some minor changes are made while moving the code. Casts from void *
aren't necessary, so drop them, and rename felix_irq_handler() to the
more specific vsc9959_irq_handler().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init and teardown code,
which could be made common [1]. The teardown code could even be
simplified away if we made use of devres, something which is used here
and there in the felix driver, just not very consistently.
[1] https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Prepare the ground in the felix_vsc9959 driver, by allocating the data
structures using devres and deleting the kfree() calls. This also
deletes the "Failed to allocate ..." message, since memory allocation
errors are extremely loud anyway, and it's hard to miss them.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6fffbc7ae1 ("PCI: Honor firmware's device disabled
status"), PCI device drivers with OF bindings no longer need this check.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init and teardown code,
which could be made common [1]. The teardown code could even be
simplified away if we made use of devres, something which is used here
and there in the felix driver, just not very consistently.
[1] https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Prepare the ground in the seville_vsc9953 driver, by allocating the data
structures using devres and deleting the kfree() calls. This also
deletes the "Failed to allocate ..." message, since memory allocation
errors are extremely loud anyway, and it's hard to miss them.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init and teardown code,
which could be made common [1]. The teardown code could even be
simplified away if we made use of devres, something which is used here
and there in the felix driver, just not very consistently.
[1] https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Prepare the ground in the ocelot_ext driver, by allocating the data
structures using devres and deleting the kfree() calls. This also
deletes the "Failed to allocate ..." message, since memory allocation
errors are extremely loud anyway, and it's hard to miss them.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/ti/icssg/icssg_classifier.c
abd5576b9c ("net: ti: icssg-prueth: Add support for ICSSG switch firmware")
56a5cf538c ("net: ti: icssg-prueth: Fix start counter for ft1 filter")
https://lore.kernel.org/all/20240531123822.3bb7eadf@canb.auug.org.au/
No other adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver should return RMII interface when XMII is running in RMII mode.
Fixes: 0ab7f6bf16 ("net: dsa: microchip: ksz9477: use common xmii function")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Acked-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1716932066-3342-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert felix to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/E1sByYA-00EM0y-Jn@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both LAN9303 and LAN9354 have internal PHYs on both external ports.
Therefore a configuration without SMSC PHY support is non-practical at
least and leads to:
LAN9303_MDIO 8000f00.mdio:00: Found LAN9303 rev. 1
mdio_bus 8000f00.mdio:00: deferred probe pending: (reason unknown)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240528073147.3604083-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
Adjust the initialization sequence of KSZ88x3 switches to enable
802.1p priority control on Port 2 before configuring Port 1. This
change ensures the apptrust functionality on Port 1 operates
correctly, as it depends on the priority settings of Port 2. The
prior initialization sequence incorrectly configured Port 1 first,
which could lead to functional discrepancies.
Fixes: a1ea57710c ("net: dsa: microchip: dcb: add special handling for KSZ88X3 family")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240517050121.2174412-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before DCB support, the KSZ driver had only PCP as source of packet
priority values. To avoid regressions, make PCP only as default value.
User will need enable DSCP support manually.
This patch do not affect other KSZ8 related quirks. User will still be
warned by setting not support configurations for the port 2.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All other functions are commented. Add missing comments to following
functions:
ksz_set_global_dscp_entry()
ksz_port_add_dscp_prio()
ksz_port_del_dscp_prio()
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPV is added and used term in 802.1Qci PSFP and merged into 802.1Q (from
802.1Q-2018) for another functions.
Even it does similar operation holding temporal priority value
internally (as it is named), because KSZ datasheet doesn't use the term
of IPV (Internal Priority Value) and avoiding any confusion later when
PSFP is in the Linux world, it is better to rename IPV to IPM (Internal
Priority Mapping).
In addition, LAN937x documentation already use IPV for 802.1Qci PSFP
related functionality.
Suggested-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
35d92abfba ("net: hns3: fix kernel crash when devlink reload during initialization")
2a1a1a7b5f ("net: hns3: add command queue trace for hns3")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the mv88e6320 and 6321 switch family, port 0/1 are serdes only ports.
Modified the mv88e6352_get_port4_serdes_cmode function to pass a port
number since the register set of the 6352 is equal on the 6320/21.
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240508072944.54880-3-steffen@innosonix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As of commit de5c9bf40c ("net: phylink: require supported_interfaces to
be filled")
Marvell 88e6320/21 switches fail to be probed:
...
mv88e6085 30be0000.ethernet-1:00: phylink: error: empty supported_interfaces
error creating PHYLINK: -22
...
The problem stems from the use of mv88e6185_phylink_get_caps() to get
the device capabilities.
Since there are serdes only ports 0/1 included, create a new dedicated
phylink_get_caps for the 6320 and 6321 to properly support their
set of capabilities.
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240508072944.54880-2-steffen@innosonix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Microchip KSZ and LAN variants do not have per port DSCP priority
configuration. Instead there is a global DSCP mapping table.
This patch provides write access to this global DSCP map. In case entry
is "deleted", we map corresponding DSCP entry to a best effort prio,
which is expected to be the default priority for all untagged traffic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
802.1P (PCP) and DiffServ (DSCP) are handled now by DCB code. Let it do
all needed initial configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Init priority to queue mapping in the way as it shown in IEEE 802.1Q
mapping example.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tested ETS support on KSZ9893, so it should work other KSZ989X
variants too, which was till not listed as support.
With this change we now officially not support only ksz8 family of
chips.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ88X3 switches have different behavior on different ports:
- It seems to be not possible to disable VLAN PCP classification on port
2. It means, as soon as mutliqueue support is enabled, frames with
VLAN tag will get PCP prios. This behavior do not affect Port 1 -
it is possible to disable PCP prios.
- DSCP classification is not working on Port 2.
Since there are still usable configuration combinations, I added some
quirks to make sure user will get appropriate error message if not
possible configuration is chosen.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DCB support to configure app trust sources and default port priority.
Following commands can be used for testing:
dcb apptrust set dev lan1 order pcp dscp
dcb app replace dev lan1 default-prio 3
Since it is not possible to configure DSCP-Prio mapping per port, this
patch provide only ability to read switch global dscp-prio mapping and
way to enable/disable app trust for DSCP.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ88X3 switches support up to 4 queues. Rework ksz8795_set_prio_queue()
to support KSZ8795 and KSZ88X3 families of switches.
Per default, configure KSZ88X3 to use one queue, since it need special
handling due to priority related errata. Errata handling is implemented
in a separate patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of Microchip KSZ switches use Internal Priority Value associated
with every frame. For example, it is possible to map any VLAN PCP or
DSCP value to IPV and at the end, map IPV to a queue.
Since amount of IPVs is not equal to amount of queues, add this
information and make use of it in some functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the MT7530 DSA subdriver configures the MT7530 switch to provide
direct access to switch PHYs, meaning, the switch PHYs listen on the MDIO
bus the switch listens on. The PHY muxing feature makes use of this.
This is problematic as the PHY may be attached before the switch is
initialised, in which case, the PHY will fail to be attached.
Since commit 91374ba537 ("net: dsa: mt7530: support OF-based registration
of switch MDIO bus"), we can describe the switch PHYs on the MDIO bus of
the switch on the device tree. Extend the check to detect PHY muxing when
the PHY is defined on the MDIO bus of the switch on the device tree.
When the PHY is described this way, the switch will be initialised first,
then the switch MDIO bus will be registered. Only after these steps, the
PHY will be attached.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240430-b4-for-netnext-mt7530-use-switch-mdio-bus-for-phy-muxing-v2-1-9104d886d0db@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since commit a3c53be55c ("net: dsa: mv88e6xxx: Support multiple MDIO
busses") mv88e6xxx_default_mdio_bus() has checked that the
return value of list_first_entry() is non-NULL.
This appears to be intended to guard against the list chip->mdios being
empty. However, it is not the correct check as the implementation of
list_first_entry is not designed to return NULL for empty lists.
Instead, use list_first_entry_or_null() which does return NULL if the
list is empty.
Flagged by Smatch.
Compile tested only.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240430-mv88e6xx-list_empty-v3-1-c35c69d88d2e@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
include/linux/filter.h
kernel/bpf/core.c
66e13b615a ("bpf: verifier: prevent userspace memory access")
d503a04f8b ("bpf: Add support for certain atomics in bpf_arena to x86 JIT")
https://lore.kernel.org/all/20240429114939.210328b0@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Topaz family (88E6141 and 88E6341) only support 256 Forwarding
Information Tables.
Fixes: a75961d0eb ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6341")
Fixes: 1558727a1c ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6141")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240429133832.9547-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert realtek to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. We need to provide a stub for
the mandatory mac_config() method for rtl8366rb.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/E1s11qJ-00AHi0-Kk@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
DSA initalises the ds->num_ports amount of ports in
dsa_switch_touch_ports(). When the PHY muxing feature is in use, port 5
won't be defined in the device tree. Because of this, the type member of
the dsa_port structure for this port will be assigned DSA_PORT_TYPE_UNUSED.
The dsa_port_setup() function calls ds->ops->port_disable() when the port
type is DSA_PORT_TYPE_UNUSED.
The MT7530_P5_DIS bit is unset in mt7530_setup() when PHY muxing is being
used. mt7530_port_disable() which is assigned to ds->ops->port_disable() is
called afterwards. Currently, mt7530_port_disable() sets MT7530_P5_DIS
which breaks network connectivity when PHY muxing is being used.
Therefore, do not set MT7530_P5_DIS when PHY muxing is being used.
Fixes: 377174c576 ("net: dsa: mt7530: move MT753X_MTRAP operations for MT7530")
Reported-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240428-for-netnext-mt7530-do-not-disable-port5-when-phy-muxing-v2-1-bb7c37d293f8@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert ksz_common to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1s0O7H-009gpq-IF@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phylink_mac_config function pointer member of struct ksz_dev_ops is
never initialised, so let's remove it to simplify the code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1s0O7C-009gpk-Dh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit introduces LED drivers for rtl8366rb, enabling LEDs to be
described in the device tree using the same format as qca8k. Each port
can configure up to 4 LEDs.
If all LEDs in a group use the default state "keep", they will use the
default behavior after a reset. Changing the brightness of one LED,
either manually or by a trigger, will disable the default hardware
trigger and switch the entire LED group to manually controlled LEDs.
Once in this mode, there is no way to revert to hardware-controlled LEDs
(except by resetting the switch).
Software triggers function as expected with manually controlled LEDs.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The necessity of asserting the reset on removal was previously
questioned, as DSA's own cleanup methods should suffice to prevent
traffic leakage[1].
When a driver has subdrivers controlled by devres, they will be
unregistered after the main driver's .remove is executed. If it asserts
a reset, the subdrivers will be unable to communicate with the hardware
during their cleanup. For LEDs, this means that they will fail to turn
off, resulting in a timeout error.
[1] https://lore.kernel.org/r/20240123215606.26716-9-luizluca@gmail.com/
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch family supports four LEDs for each of its six ports. Each
LED group is composed of one of these four LEDs from all six ports. LED
groups can be configured to display hardware information, such as link
activity, or manually controlled through a bitmap in registers
RTL8366RB_LED_0_1_CTRL_REG and RTL8366RB_LED_2_3_CTRL_REG.
After a reset, the default LED group configuration for groups 0 to 3
indicates, respectively, link activity, link at 1000M, 100M, and 10M, or
RTL8366RB_LED_CTRL_REG as 0x5432. These configurations are commonly used
for LED indications. However, the driver was replacing that
configuration to use manually controlled LEDs (RTL8366RB_LED_FORCE)
without providing a way for the OS to control them. The default
configuration is deemed more useful than fixed, uncontrollable turned-on
LEDs.
The driver was enabling/disabling LEDs during port_enable/disable.
However, these events occur when the port is administratively controlled
(up or down) and are not related to link presence. Additionally, when a
port N was disabled, the driver was turning off all LEDs for group N,
not only the corresponding LED for port N in any of those 4 groups. In
such cases, if port 0 was brought down, the LEDs for all ports in LED
group 0 would be turned off. As another side effect, the driver was
wrongly warning that port 5 didn't have an LED ("no LED for port 5").
Since showing the administrative state of ports is not an orthodox way
to use LEDs, it was not worth it to fix it and all this code was
dropped.
The code to disable LEDs was simplified only changing each LED group to
the RTL8366RB_LED_OFF state. Registers RTL8366RB_LED_0_1_CTRL_REG and
RTL8366RB_LED_2_3_CTRL_REG are only used when the corresponding LED
group is configured with RTL8366RB_LED_FORCE and they don't need to be
cleaned. The code still references an LED controlled by
RTL8366RB_INTERRUPT_CONTROL_REG, but as of now, no test device has
actually used it. Also, some magic numbers were replaced by macros.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert b53 to provide its own phylink MAC operations, thus avoiding the
shim layer in DSA's port.c
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-9-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Only use the PHYLINK implementation from there on now that an equivalent
configuration is applied to all of the switch ports.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-8-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
And make sure this is done for the MLO_AN_PHY case, where it actually
makes sense, contrary to b53_adjust_link() which only did it for
fixed-PHY configurations where it does not make sense.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-7-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call b53_adjust_531x5_rgmii() and b53_adjust_5325_mii() from
b53_phylink_mac_config() when we have a fixed PHY in preparation for removing
b53_adjust_link(). Also move b53_adjust_63xx_rgmii() to
b53_phylink_mac_config() where it logically belongs.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-6-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Just like what b53_adjust_link() does, force flow control for the
BCM5301X CPU port(s) by forcing rx_pause and tx_pause in
b53_phylink_mac_link_up(). Preparatory step for getting rid of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-5-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Takes care of doing the 5325 switch series specific MII programming and
is called from b53_adjust_link() to allow the future removal of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-4-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Takes care of doing the 531x5 switch series specific RGMII programming
and is called from b53_adjust_link() to allow the future removal of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-3-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
They are not used outside of the b53_common.c file, no need to be
exported.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
88E6250-family switches have the quirk that the EEPROM Running flag can
get stuck at 1 when no EEPROM is connected, causing
mv88e6xxx_g2_eeprom_wait() to time out. We still want to wait for the
EEPROM however, to avoid interrupting a transfer and leaving the EEPROM
in an invalid state.
The condition to wait for recommended by the hardware spec is the EEInt
flag, however this flag is cleared on read, so before the hardware reset,
is may have been cleared already even though the EEPROM has been read
successfully.
For this reason, we revive the mv88e6xxx_g1_wait_eeprom_done() function
that was removed in commit 6ccf50d4d4
("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent") in a
slightly refactored form, and introduce a new
mv88e6xxx_g1_wait_eeprom_done_prereset() that additionally handles this
case by triggering another EEPROM reload that can be waited on.
On other switch models without this quirk, mv88e6xxx_g2_eeprom_wait() is
kept, as it avoids the additional reload.
Fixes: 6ccf50d4d4 ("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of calling mv88e6xxx_g2_eeprom_wait() directly from
mv88e6xxx_hardware_reset(), add configurable pre- and post-reset hard
reset handlers. Initially, the handlers are set to
mv88e6xxx_g2_eeprom_wait() for all families that have get/set_eeprom()
to match the existing behavior. No functional change intended (except
for additional error messages on failure).
Fixes: 6ccf50d4d4 ("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike MT7531BE, the GPIO 6-12 pins are not used for RGMII on MT7531AE.
Therefore, the GPIO 11-12 pins are set to function as MDC and MDIO to
expose the MDIO bus of the switch. Replace the comment with a better
explanation.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mt7531_rgmii_setup() function does not use the port variable, do not
pass the variable to it.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use priv->ds->num_ports on all for loops which configure the switch
registers. In the future, the value of MT7530_NUM_PORTS will depend on
priv->id. Therefore, this change prepares the subdriver for a simpler
implementation.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac_port_validate member of the mt753x_info structure is not being
used, remove it. Improve the member description section in the process.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7530_PMEEECR_P() register is on MT7530, MT7531, and the switch on the
MT7988 SoC. Rename the definition for them to MT753X_PMEEECR_P(). Use the
FIELD_PREP and FIELD_GET macros. Rename GET_LPI_THRESH() and
SET_LPI_THRESH() to LPI_THRESH_GET() and LPI_THRESH_SET().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of checking whether functions are filled properly. priv->info which
is an mt753x_info structure is filled and checked for before this check.
It's unnecessary checking whether it's filled properly.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support of the MT7988 SoC switch, the MAC speed capabilities
defined on mt753x_phylink_get_caps() won't apply to all switch models
anymore. Move them to more appropriate locations instead of overwriting
config->mac_capabilities.
Remove the comment on mt753x_phylink_get_caps() as it's become invalid with
the support of MT7531 and MT7988 SoC switch.
Add break to case 6 of mt7988_mac_port_get_caps() to be explicit.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mt7530_setup_mdio() and mt7531_setup_common() functions should be
checked for errors. Return if the functions return a non-zero value.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On MT7530, the media-independent interfaces of port 5 and 6 are controlled
by the MT7530_P5_DIS and MT7530_P6_DIS bits of the hardware trap. Deal with
these bits only when the relevant port is being enabled or disabled. This
ensures that these ports will be disabled when they are not in use.
Do not set MT7530_CHG_TRAP on mt7530_setup_port5() as that's already being
done on mt7530_setup().
Instead of globally setting MT7530_P5_MAC_SEL, clear it, then set it only
on the appropriate case.
If PHY muxing is detected, clear MT7530_P5_DIS before calling
mt7530_setup_port5().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7530_HWTRAP and MT7530_MHWTRAP registers are on MT7530 and MT7531.
It's called hardware trap on MT7530, software trap on MT7531. That's
because some bits of the trap on MT7530 cannot be modified by software
whilst all bits of the trap on MT7531 can. Rename the definitions for them
to MT753X_TRAP and MT753X_MTRAP. Add MT7530 and MT7531 prefixes to the
definitions specific to the switch model.
Remove the extra parentheses from MT7530_XTAL_40MHZ and MT7530_XTAL_20MHZ.
Rename MHWTRAP_PHY0_SEL, MHWTRAP_MANUAL, and MHWTRAP_PHY_ACCESS to be on
par with the "MT7621 Giga Switch Programming Guide v0.3" document.
Make an enumaration for the XTAL frequency. Set the data type of the xtal
variable on mt7531_pll_setup() to it.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7530_MFC register is on MT7530, MT7531, and the switch on the MT7988
SoC. Rename it to MT753X_MFC. Bit 7 to 0 differs between MT7530 and
MT7531/MT7988. Add MT7530 prefix to these definitions, and define the
IGMP/MLD Query Frame Flooding Ports mask for MT7531.
Rename the cases of MIRROR_MASK to MIRROR_PORT_MASK.
Move mt753x_mirror_port_get() and mt753x_port_mirror_set() to mt7530.h as
macros.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mt753x_bpdu_port_fw enum is globally used for manipulating the process
of deciding the forwardable ports, specifically concerning the CPU port(s).
Therefore, rename it and the values in it to mt753x_to_cpu_fw.
Change FOLLOW_MFC to SYSTEM_DEFAULT to be on par with the switch documents.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The p5_intf_sel pointer is used to store the information of whether PHY
muxing is used or not. PHY muxing is a feature specific to port 5 of the
MT7530 switch. Do not use it for other switch models.
Rename the pointer to p5_mode to store the mode the port is being used in.
Rename the p5_interface_select enum to mt7530_p5_mode, the string
representation to mt7530_p5_mode_str, and the enum elements.
If PHY muxing is not detected, the default mode, GMAC5, will be used.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7530_PMCR_P() registers are on MT7530, MT7531, and the switch on the
MT7988 SoC. Rename the definition for them to MT753X_PMCR_P(). Bit 15 is
for MT7530 only. Add MT7530 prefix to the definition for bit 15.
Use GENMASK and FIELD_PREP for PMCR_IFG_XMIT().
Rename PMCR_TX_EN and PMCR_RX_EN to PMCR_MAC_TX_EN and PMCR_MAC_TX_EN to
follow the naming on the "MT7621 Giga Switch Programming Guide v0.3",
"MT7531 Reference Manual for Development Board v1.0", and "MT7988A Wi-Fi 7
Generation Router Platform: Datasheet (Open Version) v0.1" documents.
These documents show that PMCR_RX_FC_EN is at bit 5. Correct this along
with renaming it to PMCR_FORCE_RX_FC_EN, and the same for PMCR_TX_FC_EN.
Remove PMCR_SPEED_MASK which doesn't have a use.
Rename the force mode definitions for MT7531 to FORCE_MODE. Add MASK at the
end for the mask that includes all force mode definitions.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7531_FORCE_EEE1G and MT7531_FORCE_EEE100 bits let the
PMCR_FORCE_EEE1G and PMCR_FORCE_EEE100 bits determine the 1G/100 EEE
abilities of the MAC. If MT7531_FORCE_EEE1G and MT7531_FORCE_EEE100 are
unset, the abilities are left to be determined by PHY auto polling.
The commit 40b5d2f15c ("net: dsa: mt7530: Add support for EEE features")
made it so that the PMCR_FORCE_EEE1G and PMCR_FORCE_EEE100 bits are set on
mt753x_phylink_mac_link_up(). But it did not set the MT7531_FORCE_EEE1G and
MT7531_FORCE_EEE100 bits. Because of this, the EEE abilities will be
determined by PHY auto polling, regardless of the result of phy_init_eee().
Define these bits and add them to the MT7531_FORCE_MODE mask which is set
in mt7531_setup_common(). With this, there won't be any EEE abilities set
when phy_init_eee() returns a negative value.
Thanks to Russell for explaining when phy_init_eee() could return a
negative value below.
Looking at phy_init_eee(), it could return a negative value when:
1. phydev->drv is NULL
2. if genphy_c45_eee_is_active() returns negative
3. if genphy_c45_eee_is_active() returns zero, it returns -EPROTONOSUPPORT
4. if phy_set_bits_mmd() fails (e.g. communication error with the PHY)
If we then look at genphy_c45_eee_is_active(), then:
genphy_c45_read_eee_adv() and genphy_c45_read_eee_lpa() propagate their
non-zero return values, otherwise this function returns zero or positive
integer.
If we then look at genphy_c45_read_eee_adv(), then a failure of
phy_read_mmd() would cause a negative value to be returned.
Looking at genphy_c45_read_eee_lpa(), the same is true.
So, it can be summarised as:
- phydev->drv is NULL
- there is a communication error accessing the PHY
- EEE is not active
otherwise, it returns zero on success.
If one wishes to determine whether an error occurred vs EEE not being
supported through negotiation for the negotiated speed, if it returns
-EPROTONOSUPPORT in the latter case. Other error codes mean either the
driver has been unloaded or communication error.
In conclusion, determining the EEE abilities by PHY auto polling shouldn't
result in having any EEE abilities enabled, when one of the last two
situations in the summary happens. And it seems that if phydev->drv is
NULL, there would be bigger problems with the device than a broken link. So
this is not a bugfix.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The core_rmw() function calls core_read_mmd_indirect() to read the
requested register, and then calls core_write_mmd_indirect() to write the
requested value to the register. Because Clause 22 is used to access Clause
45 registers, some operations on core_write_mmd_indirect() are
unnecessarily run. Get rid of core_read_mmd_indirect() and
core_write_mmd_indirect(), and run only the necessary operations on
core_write() and core_rmw().
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Read the PHY address the switch listens on from the reg property of the
switch node on the device tree. This change brings support for MT7530
switches on boards with such bootstrapping configuration where the switch
listens on a different PHY address than the hardcoded PHY address on the
driver, 31.
As described on the "MT7621 Programming Guide v0.4" document, the MT7530
switch and its PHYs can be configured to listen on the range of 7-12,
15-20, 23-28, and 31 and 0-4 PHY addresses.
There are operations where the switch PHY registers are used. For the PHY
address of the control PHY, transform the MT753X_CTRL_PHY_ADDR constant
into a macro and use it. The PHY address for the control PHY is 0 when the
switch listens on 31. In any other case, it is one greater than the PHY
address the switch listens on.
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This commit adds updates to the documentation describing the structures
used in vsc73xx. This will help prevent kdoc-related issues in the future.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://lore.kernel.org/r/20240417205048.3542839-6-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch introduces a new define: VSC73XX_MAX_NUM_PORTS, which can be
used in the future instead of a hardcoded value.
Currently, the only hardcoded value is vsc->ds->num_ports. It is being
replaced with the new define.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240417205048.3542839-5-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's preparation for future use. At this moment, the RGMII port is used
only for a connection to the MAC interface, but in the future, someone
could connect a PHY to it. Using the "phy_interface_mode_is_rgmii" macro
allows for the proper recognition of all RGMII modes.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240417205048.3542839-4-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch replaces the adjust_link api with the phylink apis that provide
equivalent functionality.
The remaining functionality from the adjust_link is now covered in the
mac_link_* and mac_config from phylink_mac_ops structure.
Removes:
.adjust_link
Adds phylink_mac_ops structure:
.mac_config
.mac_link_up
.mac_link_down
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://lore.kernel.org/r/20240417205048.3542839-3-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Switch the delay loop during the Arbiter empty check from
vsc73xx_adjust_link() to use read_poll_timeout(). Functionally,
one msleep() call is eliminated at the end of the loop in the timeout
case.
As Russell King suggested:
"This [change] avoids the issue that on the last iteration, the code reads
the register, tests it, finds the condition that's being waiting for is
false, _then_ waits and end up printing the error message - that last
wait is rather useless, and as the arbiter state isn't checked after
waiting, it could be that we had success during the last wait."
Suggested-by: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://lore.kernel.org/r/20240417205048.3542839-2-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the recent PHYLINK changes requiring supported_interfaces to be set,
MV88E6250 family switches like the 88E6020 fail to probe - cmode is
never initialized on these devices, so mv88e6250_phylink_get_caps() does
not set any supported_interfaces flags.
Instead of a cmode, on 88E6250 we have a read-only port mode value that
encodes similar information. There is no reason to bother mapping port
mode to the cmodes of other switch models; instead we introduce a
mv88e6250_setup_supported_interfaces() that is called directly from
mv88e6250_phylink_get_caps().
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240417103737.166651-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The kernel build bot identified the following mistake in the recently
merged 860a9bed26 ("net: dsa: xrs700x: provide own phylink MAC
operations") patch:
drivers/net/dsa/xrs700x/xrs700x.c:714:37: warning: 'xrs700x_phylink_mac_ops' defined but not used [-Wunused-const-variable=]
714 | static const struct phylink_mac_ops xrs700x_phylink_mac_ops = {
| ^~~~~~~~~~~~~~~~~~~~~~~
Fix the omitted assignment of ds->phylink_mac_ops.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver currently doesn't support any control flags.
Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Link: https://lore.kernel.org/r/20240417144413.104257-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver currently doesn't support any control flags.
Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Link: https://lore.kernel.org/r/20240417144407.104241-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert xrs700x to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. We need to provide stubs for
the mac_link_down() and mac_config() methods which are mandatory.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1rwfu8-007531-TG@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert rzn1_a5psw to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. We need to provide a stub for
the mac_config() method which is mandatory.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1rwfuJ-00753D-6d@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert lan9303 to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. We need to provide stubs for
the mac_link_down() and mac_config() methods which are mandatory.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1rwfuE-007537-1u@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert bcm_sf2 to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rwfu3-00752s-On@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "MT7988A Wi-Fi 7 Generation Router Platform: Datasheet (Open Version)
v0.1" document shows bits 16 to 18 as the MIRROR_PORT field of the CPU
forward control register. Currently, the MT7530 DSA subdriver configures
bits 0 to 2 of the CPU forward control register which breaks the port
mirroring feature for the MT7988 SoC switch.
Fix this by using the MT7531_MIRROR_PORT_GET() and MT7531_MIRROR_PORT_SET()
macros which utilise the correct bits.
Fixes: 110c18bfed ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch intellectual property provides a bit on the ARL global control
register which controls allowing mirroring frames which are received on the
local port (monitor port). This bit is unset after reset.
This ability must be enabled to fully support the port mirroring feature on
this switch intellectual property.
Therefore, this patch fixes the traffic not being reflected on a port,
which would be configured like below:
tc qdisc add dev swp0 clsact
tc filter add dev swp0 ingress matchall skip_sw \
action mirred egress mirror dev swp0
As a side note, this configuration provides the hairpinning feature for a
single port.
Fixes: 37feab6076 ("net: dsa: mt7530: add support for port mirroring")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ID table already has respective entry and MODULE_DEVICE_TABLE and
creates proper alias for SPI driver. Having another MODULE_ALIAS causes
the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240414154929.127045-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert mt753x to provide its own phylink MAC operations, thus avoiding
the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/E1rvIco-006bQu-Fq@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert lantiq_gswip to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c. For lantiq_gswip, it means
we end up with a common instance of phylink MAC operations that are
shared between the different variants, rather than having duplicated
initialisers in dsa_switch_ops.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1rvIcj-006bQo-B3@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert qca8k to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rvIce-006bQi-58@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert ar9331 to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rvIcZ-006bQc-0W@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert sja1105 to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rvIcT-006bQW-S3@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add check for unsupported control flags.
Only compile-tested, no access to HW.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mv88e6xxx to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rudqK-006K9N-HY@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In Clause 5 of IEEE Std 802-2014, two sublayers of the data link layer
(DLL) of the Open Systems Interconnection basic reference model (OSI/RM)
are described; the medium access control (MAC) and logical link control
(LLC) sublayers. The MAC sublayer is the one facing the physical layer.
In 8.2 of IEEE Std 802.1Q-2022, the Bridge architecture is described. A
Bridge component comprises a MAC Relay Entity for interconnecting the Ports
of the Bridge, at least two Ports, and higher layer entities with at least
a Spanning Tree Protocol Entity included.
Each Bridge Port also functions as an end station and shall provide the MAC
Service to an LLC Entity. Each instance of the MAC Service is provided to a
distinct LLC Entity that supports protocol identification, multiplexing,
and demultiplexing, for protocol data unit (PDU) transmission and reception
by one or more higher layer entities.
It is described in 8.13.9 of IEEE Std 802.1Q-2022 that in a Bridge, the LLC
Entity associated with each Bridge Port is modeled as being directly
connected to the attached Local Area Network (LAN).
On the switch with CPU port architecture, CPU port functions as Management
Port, and the Management Port functionality is provided by software which
functions as an end station. Software is connected to an IEEE 802 LAN that
is wholly contained within the system that incorporates the Bridge.
Software provides access to the LLC Entity associated with each Bridge Port
by the value of the source port field on the special tag on the frame
received by software.
We call frames that carry control information to determine the active
topology and current extent of each Virtual Local Area Network (VLAN),
i.e., spanning tree or Shortest Path Bridging (SPB) and Multiple VLAN
Registration Protocol Data Units (MVRPDUs), and frames from other link
constrained protocols, such as Extensible Authentication Protocol over LAN
(EAPOL) and Link Layer Discovery Protocol (LLDP), link-local frames. They
are not forwarded by a Bridge. Permanently configured entries in the
filtering database (FDB) ensure that such frames are discarded by the
Forwarding Process. In 8.6.3 of IEEE Std 802.1Q-2022, this is described in
detail:
Each of the reserved MAC addresses specified in Table 8-1
(01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]) shall be
permanently configured in the FDB in C-VLAN components and ERs.
Each of the reserved MAC addresses specified in Table 8-2
(01-80-C2-00-00-[01,02,03,04,05,06,07,08,09,0A,0E]) shall be permanently
configured in the FDB in S-VLAN components.
Each of the reserved MAC addresses specified in Table 8-3
(01-80-C2-00-00-[01,02,04,0E]) shall be permanently configured in the FDB
in TPMR components.
The FDB entries for reserved MAC addresses shall specify filtering for all
Bridge Ports and all VIDs. Management shall not provide the capability to
modify or remove entries for reserved MAC addresses.
The addresses in Table 8-1, Table 8-2, and Table 8-3 determine the scope of
propagation of PDUs within a Bridged Network, as follows:
The Nearest Bridge group address (01-80-C2-00-00-0E) is an address that
no conformant Two-Port MAC Relay (TPMR) component, Service VLAN (S-VLAN)
component, Customer VLAN (C-VLAN) component, or MAC Bridge can forward.
PDUs transmitted using this destination address, or any other addresses
that appear in Table 8-1, Table 8-2, and Table 8-3
(01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]), can
therefore travel no further than those stations that can be reached via a
single individual LAN from the originating station.
The Nearest non-TPMR Bridge group address (01-80-C2-00-00-03), is an
address that no conformant S-VLAN component, C-VLAN component, or MAC
Bridge can forward; however, this address is relayed by a TPMR component.
PDUs using this destination address, or any of the other addresses that
appear in both Table 8-1 and Table 8-2 but not in Table 8-3
(01-80-C2-00-00-[00,03,05,06,07,08,09,0A,0B,0C,0D,0F]), will be relayed
by any TPMRs but will propagate no further than the nearest S-VLAN
component, C-VLAN component, or MAC Bridge.
The Nearest Customer Bridge group address (01-80-C2-00-00-00) is an
address that no conformant C-VLAN component, MAC Bridge can forward;
however, it is relayed by TPMR components and S-VLAN components. PDUs
using this destination address, or any of the other addresses that appear
in Table 8-1 but not in either Table 8-2 or Table 8-3
(01-80-C2-00-00-[00,0B,0C,0D,0F]), will be relayed by TPMR components and
S-VLAN components but will propagate no further than the nearest C-VLAN
component or MAC Bridge.
Because the LLC Entity associated with each Bridge Port is provided via CPU
port, we must not filter these frames but forward them to CPU port.
In a Bridge, the transmission Port is majorly decided by ingress and egress
rules, FDB, and spanning tree Port State functions of the Forwarding
Process. For link-local frames, only CPU port should be designated as
destination port in the FDB, and the other functions of the Forwarding
Process must not interfere with the decision of the transmission Port. We
call this process trapping frames to CPU port.
Therefore, on the switch with CPU port architecture, link-local frames must
be trapped to CPU port, and certain link-local frames received by a Port of
a Bridge comprising a TPMR component or an S-VLAN component must be
excluded from it.
A Bridge of the switch with CPU port architecture cannot comprise a
Two-Port MAC Relay (TPMR) component as a TPMR component supports only a
subset of the functionality of a MAC Bridge. A Bridge comprising two Ports
(Management Port doesn't count) of this architecture will either function
as a standard MAC Bridge or a standard VLAN Bridge.
Therefore, a Bridge of this architecture can only comprise S-VLAN
components, C-VLAN components, or MAC Bridge components. Since there's no
TPMR component, we don't need to relay PDUs using the destination addresses
specified on the Nearest non-TPMR section, and the proportion of the
Nearest Customer Bridge section where they must be relayed by TPMR
components.
One option to trap link-local frames to CPU port is to add static FDB
entries with CPU port designated as destination port. However, because that
Independent VLAN Learning (IVL) is being used on every VID, each entry only
applies to a single VLAN Identifier (VID). For a Bridge comprising a MAC
Bridge component or a C-VLAN component, there would have to be 16 times
4096 entries. This switch intellectual property can only hold a maximum of
2048 entries. Using this option, there also isn't a mechanism to prevent
link-local frames from being discarded when the spanning tree Port State of
the reception Port is discarding.
The remaining option is to utilise the BPC, RGAC1, RGAC2, RGAC3, and RGAC4
registers. Whilst this applies to every VID, it doesn't contain all of the
reserved MAC addresses without affecting the remaining Standard Group MAC
Addresses. The REV_UN frame tag utilised using the RGAC4 register covers
the remaining 01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F] destination
addresses. It also includes the 01-80-C2-00-00-22 to 01-80-C2-00-00-FF
destination addresses which may be relayed by MAC Bridges or VLAN Bridges.
The latter option provides better but not complete conformance.
This switch intellectual property also does not provide a mechanism to trap
link-local frames with specific destination addresses to CPU port by
Bridge, to conform to the filtering rules for the distinct Bridge
components.
Therefore, regardless of the type of the Bridge component, link-local
frames with these destination addresses will be trapped to CPU port:
01-80-C2-00-00-[00,01,02,03,0E]
In a Bridge comprising a MAC Bridge component or a C-VLAN component:
Link-local frames with these destination addresses won't be trapped to
CPU port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F]
In a Bridge comprising an S-VLAN component:
Link-local frames with these destination addresses will be trapped to CPU
port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-00
Link-local frames with these destination addresses won't be trapped to
CPU port which won't conform to IEEE Std 802.1Q-2022:
01-80-C2-00-00-[04,05,06,07,08,09,0A]
Currently on this switch intellectual property, if the spanning tree Port
State of the reception Port is discarding, link-local frames will be
discarded.
To trap link-local frames regardless of the spanning tree Port State, make
the switch regard them as Bridge Protocol Data Units (BPDUs). This switch
intellectual property only lets the frames regarded as BPDUs bypass the
spanning tree Port State function of the Forwarding Process.
With this change, the only remaining interference is the ingress rules.
When the reception Port has no PVID assigned on software, VLAN-untagged
frames won't be allowed in. There doesn't seem to be a mechanism on the
switch intellectual property to have link-local frames bypass this function
of the Forwarding Process.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240409-b4-for-net-mt7530-fix-link-local-when-stp-discarding-v2-1-07b1150164ac@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The commit 40b5d2f15c ("net: dsa: mt7530: Add support for EEE features")
brought EEE support but did not enable EEE on MT7531 switch MACs. EEE is
enabled on MT7531 switch MACs by pulling the LAN2LED0 pin low on the board
(bootstrapping), unsetting the EEE_DIS bit on the trap register, or setting
the internal EEE switch bit on the CORE_PLL_GROUP4 register. Thanks to
SkyLake Huang (黃啟澤) from MediaTek for providing information on the
internal EEE switch bit.
There are existing boards that were not designed to pull the pin low.
Because of that, the EEE status currently depends on the board design.
The EEE_DIS bit on the trap pertains to the LAN2LED0 pin which is usually
used to control an LED. Once the bit is unset, the pin will be low. That
will make the active low LED turn on. The pin is controlled by the switch
PHY. It seems that the PHY controls the pin in the way that it inverts the
pin state. That means depending on the wiring of the LED connected to
LAN2LED0 on the board, the LED may be on without an active link.
To not cause this unwanted behaviour whilst enabling EEE on all boards, set
the internal EEE switch bit on the CORE_PLL_GROUP4 register.
My testing on MT7531 shows a certain amount of traffic loss when EEE is
enabled. That said, I haven't come across a board that enables EEE. So
enable EEE on the switch MACs but disable EEE advertisement on the switch
PHYs. This way, we don't change the behaviour of the majority of the boards
that have this switch. The mediatek-ge PHY driver already disables EEE
advertisement on the switch PHYs but my testing shows that it is somehow
enabled afterwards. Disabling EEE advertisement before the PHY driver
initialises keeps it off.
With this change, EEE can now be enabled using ethtool.
Fixes: 40b5d2f15c ("net: dsa: mt7530: Add support for EEE features")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240408-for-net-mt7530-fix-eee-for-mt7531-mt7988-v3-1-84fdef1f008b@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We already have a variable to provide number of entries. So use it,
instead of using error number.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-9-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The read/write path may fail. So, return error if we got it.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-8-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
EAGAIN was not used by previous code and not used by current code. So,
remove it and use proper error value.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use 'ret' instead of 'rc' in ksz8_r_dyn_mac_table() to maintain
consistency with the rest of the file.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the code out of a long if statement scope in ksz8_r_dyn_mac_table()
to improve code readability.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor ksz8_fdb_dump() to address potential issues:
- Limit the number of iterations to avoid endless loops.
- Handle error codes returned by ksz8_r_dyn_mac_table(), with
an exception for -ENXIO when no more dynamic entries are detected.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ksz8_r_dyn_mac_table() is not used outside the source file. Make it
static.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The FDB timestamps are not being utilized. This commit removes the
unused timestamp support from ksz8_r_dyn_mac_table() function.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The definition and declaration of sja1110_pcs_mdio_write_c45() don't have
parameters in the same order.
Knowing that sja1110_pcs_mdio_write_c45() is used as a function pointer
in 'sja1105_info' structure with .pcs_mdio_write_c45, and that we have:
int (*pcs_mdio_write_c45)(struct mii_bus *bus, int phy, int mmd,
int reg, u16 val);
it is likely that the definition is the one to change.
Found with cppcheck, funcArgOrderDifferent.
Fixes: ae271547bb ("net: dsa: sja1105: C45 only transactions for PCS")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/ff2a5af67361988b3581831f7bd1eddebfb4c48f.1712082763.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Core in spi_register_driver() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240330211023.100924-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Core in spi_register_driver() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240330211023.100924-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch has 4 ports with 2 internal PHYs, but ports are numbered up
to 6, with ports 0, 1, 5 and 6 being usable.
Fixes: 71d94a432a ("net: dsa: mv88e6xxx: add support for MV88E6020 switch")
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326123655.40666-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As of commit 916444df30 ("ptp: deprecate gettime64() in favor of
gettimex64()") (new) PTP drivers should rather implement gettimex64().
In addition, this variant provides timestamps from the system clock. The
readings have to be recorded right before and after reading the lowest bits
of the PHC timestamp.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7530 switch after reset initialises with a core clock frequency that
works with a 25MHz XTAL connected to it. For 40MHz XTAL, the core clock
frequency must be set to 500MHz.
The mt7530_pll_setup() function is responsible of setting the core clock
frequency. Currently, it runs on MT7530 with 25MHz and 40MHz XTAL. This
causes MT7530 switch with 25MHz XTAL to egress and ingress frames
improperly.
Introduce a check to run it only on MT7530 with 40MHz XTAL.
The core clock frequency is set by writing to a switch PHY's register.
Access to the PHY's register is done via the MDIO bus the switch is also
on. Therefore, it works only when the switch makes switch PHYs listen on
the MDIO bus the switch is on. This is controlled either by the state of
the ESW_P1_LED_1 pin after reset deassertion or modifying bit 5 of the
modifiable trap register.
When ESW_P1_LED_1 is pulled high, PHY indirect access is used. That means
accessing PHY registers via the PHY indirect access control register of the
switch.
When ESW_P1_LED_1 is pulled low, PHY direct access is used. That means
accessing PHY registers via the MDIO bus the switch is on.
For MT7530 switch with 40MHz XTAL on a board with ESW_P1_LED_1 pulled high,
the core clock frequency won't be set to 500MHz, causing the switch to
egress and ingress frames improperly.
Run mt7530_pll_setup() after PHY direct access is set on the modifiable
trap register.
With these two changes, all MT7530 switches with 25MHz and 40MHz, and
P1_LED_1 pulled high or low, will egress and ingress frames properly.
Link: 4a5dd143f2/linux-mt/drivers/net/ethernet/mediatek/gsw_mt7623.c (L1039)
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240320-for-net-mt7530-fix-25mhz-xtal-with-direct-phy-access-v1-1-d92f605f1160@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, the MT753X switches treat frames with :01-0D and :0F MAC DAs as
regular multicast frames, therefore flooding them to user ports.
On page 205, section "8.6.3 Frame filtering" of the active standard, IEEE
Std 802.1Q™-2022, it is stated that frames with 01:80:C2:00:00:00-0F as MAC
DA must only be propagated to C-VLAN and MAC Bridge components. That means
VLAN-aware and VLAN-unaware bridges. On the switch designs with CPU ports,
these frames are supposed to be processed by the CPU (software). So we make
the switch only forward them to the CPU port. And if received from a CPU
port, forward to a single port. The software is responsible of making the
switch conform to the latter by setting a single port as destination port
on the special tag.
This switch intellectual property cannot conform to this part of the
standard fully. Whilst the REV_UN frame tag covers the remaining :04-0D and
:0F MAC DAs, it also includes :22-FF which the scope of propagation is not
supposed to be restricted for these MAC DAs.
Set frames with :01-03 MAC DAs to be trapped to the CPU port(s). Add a
comment for the remaining MAC DAs.
Note that the ingress port must have a PVID assigned to it for the switch
to forward untagged frames. A PVID is set by default on VLAN-aware and
VLAN-unaware ports. However, when the network interface that pertains to
the ingress port is attached to a vlan_filtering enabled bridge, the user
can remove the PVID assignment from it which would prevent the link-local
frames from being trapped to the CPU port. I am yet to see a way to forward
link-local frames while preventing other untagged frames from being
forwarded too.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Whether VLAN-aware or not, on every VID VLAN table entry that has the CPU
port as a member of it, frames are set to egress the CPU port with the VLAN
tag stacked. This is so that VLAN tags can be appended after hardware
special tag (called DSA tag in the context of Linux drivers).
For user ports on a VLAN-unaware bridge, frame ingressing the user port
egresses CPU port with only the special tag.
For user ports on a VLAN-aware bridge, frame ingressing the user port
egresses CPU port with the special tag and the VLAN tag.
This causes issues with link-local frames, specifically BPDUs, because the
software expects to receive them VLAN-untagged.
There are two options to make link-local frames egress untagged. Setting
CONSISTENT or UNTAGGED on the EG_TAG bits on the relevant register.
CONSISTENT means frames egress exactly as they ingress. That means
egressing with the VLAN tag they had at ingress or egressing untagged if
they ingressed untagged. Although link-local frames are not supposed to be
transmitted VLAN-tagged, if they are done so, when egressing through a CPU
port, the special tag field will be broken.
BPDU egresses CPU port with VLAN tag egressing stacked, received on
software:
00:01:25.104821 AF Unknown (382365846), length 106:
| STAG | | VLAN |
0x0000: 0000 6c27 614d 4143 0001 0000 8100 0001 ..l'aMAC........
0x0010: 0026 4242 0300 0000 0000 0000 6c27 614d .&BB........l'aM
0x0020: 4143 0000 0000 0000 6c27 614d 4143 0000 AC......l'aMAC..
0x0030: 0000 1400 0200 0f00 0000 0000 0000 0000 ................
BPDU egresses CPU port with VLAN tag egressing untagged, received on
software:
00:23:56.628708 AF Unknown (25215488), length 64:
| STAG |
0x0000: 0000 6c27 614d 4143 0001 0000 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
BPDU egresses CPU port with VLAN tag egressing tagged, received on
software:
00:01:34.311963 AF Unknown (25215488), length 64:
| Mess |
0x0000: 0000 6c27 614d 4143 0001 0001 0026 4242 ..l'aMAC.....&BB
0x0010: 0300 0000 0000 0000 6c27 614d 4143 0000 ........l'aMAC..
0x0020: 0000 0000 6c27 614d 4143 0000 0000 1400 ....l'aMAC......
0x0030: 0200 0f00 0000 0000 0000 0000 ............
To prevent confusing the software, force the frame to egress UNTAGGED
instead of CONSISTENT. This way, frames can't possibly be received TAGGED
by software which would have the special tag field broken.
VLAN Tag Egress Procedure
For all frames, one of these options set the earliest in this order will
apply to the frame:
- EG_TAG in certain registers for certain frames.
This will apply to frame with matching MAC DA or EtherType.
- EG_TAG in the address table.
This will apply to frame at its incoming port.
- EG_TAG in the PVC register.
This will apply to frame at its incoming port.
- EG_CON and [EG_TAG per port] in the VLAN table.
This will apply to frame at its outgoing port.
- EG_TAG in the PCR register.
This will apply to frame at its outgoing port.
EG_TAG in certain registers for certain frames:
PPPoE Discovery_ARP/RARP: PPP_EG_TAG and ARP_EG_TAG in the APC register.
IGMP_MLD: IGMP_EG_TAG and MLD_EG_TAG in the IMC register.
BPDU and PAE: BPDU_EG_TAG and PAE_EG_TAG in the BPC register.
REV_01 and REV_02: R01_EG_TAG and R02_EG_TAG in the RGAC1 register.
REV_03 and REV_0E: R03_EG_TAG and R0E_EG_TAG in the RGAC2 register.
REV_10 and REV_20: R10_EG_TAG and R20_EG_TAG in the RGAC3 register.
REV_21 and REV_UN: R21_EG_TAG and RUN_EG_TAG in the RGAC4 register.
With this change, it can be observed that a bridge interface with stp_state
and vlan_filtering enabled will properly block ports now.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On MT7530, the HT_XTAL_FSEL field of the HWTRAP register stores a 2-bit
value that represents the frequency of the crystal oscillator connected to
the switch IC. The field is populated by the state of the ESW_P4_LED_0 and
ESW_P4_LED_0 pins, which is done right after reset is deasserted.
ESW_P4_LED_0 ESW_P3_LED_0 Frequency
-----------------------------------------
0 0 Reserved
0 1 20MHz
1 0 40MHz
1 1 25MHz
On MT7531, the XTAL25 bit of the STRAP register stores this. The LAN0LED0
pin is used to populate the bit. 25MHz when the pin is high, 40MHz when
it's low.
These pins are also used with LEDs, therefore, their state can be set to
something other than the bootstrapping configuration. For example, a link
may be established on port 3 before the DSA subdriver takes control of the
switch which would set ESW_P3_LED_0 to high.
Currently on mt7530_setup() and mt7531_setup(), 1000 - 1100 usec delay is
described between reset assertion and deassertion. Some switch ICs in real
life conditions cannot always have these pins set back to the bootstrapping
configuration before reset deassertion in this amount of delay. This causes
wrong crystal frequency to be selected which puts the switch in a
nonfunctional state after reset deassertion.
The tests below are conducted on an MT7530 with a 40MHz crystal oscillator
by Justin Swartz.
With a cable from an active peer connected to port 3 before reset, an
incorrect crystal frequency (0b11 = 25MHz) is selected:
[1] [3] [5]
: : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
_____________________________
ESW_P3_LED_0 |__________________________
: : : :
: : [4]...:
: :
[2]................:
[1] Reset is asserted.
[2] Period of 1000 - 1100 usec.
[3] Reset is deasserted.
[4] Period of 315 usec. HWTRAP register is populated with incorrect
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
Increase the delay between reset_control_assert() and
reset_control_deassert(), and gpiod_set_value_cansleep(priv->reset, 0) and
gpiod_set_value_cansleep(priv->reset, 1) to 5000 - 5100 usec. This amount
ensures a higher possibility that the switch IC will have these pins back
to the bootstrapping configuration before reset deassertion.
With a cable from an active peer connected to port 3 before reset, the
correct crystal frequency (0b10 = 40MHz) is selected:
[1] [2-1] [3] [5]
: : : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
___________________ _______
ESW_P3_LED_0 |_________| |__________________
: : : : :
: [2-2]...: [4]...:
[2]................:
[1] Reset is asserted.
[2] Period of 5000 - 5100 usec.
[2-1] ESW_P3_LED_0 goes low.
[2-2] Remaining period of 5000 - 5100 usec.
[3] Reset is deasserted.
[4] Period of 310 usec. HWTRAP register is populated with bootstrapped
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
ESW_P3_LED_0 low period before reset deassertion:
5000 usec
- 5100 usec
TEST RESET HOLD
# (usec)
---------------------
1 5410
2 5440
3 4375
4 5490
5 5475
6 4335
7 4370
8 5435
9 4205
10 4335
11 3750
12 3170
13 4395
14 4375
15 3515
16 4335
17 4220
18 4175
19 4175
20 4350
Min 3170
Max 5490
Median 4342.500
Avg 4466.500
Revert commit 2920dd92b9 ("net: dsa: mt7530: disable LEDs before reset").
Changing the state of pins via reset assertion is simpler and more
efficient than doing so by setting the LED controller off.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Co-developed-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable LEDs just before resetting the MT7530 to avoid
situations where the ESW_P4_LED_0 and ESW_P3_LED_0 pin
states may cause an unintended external crystal frequency
to be selected.
The HT_XTAL_FSEL (External Crystal Frequency Selection)
field of HWTRAP (the Hardware Trap register) stores a
2-bit value that represents the state of the ESW_P4_LED_0
and ESW_P4_LED_0 pins (seemingly) sampled just after the
MT7530 has been reset, as:
ESW_P4_LED_0 ESW_P3_LED_0 Frequency
-----------------------------------------
0 1 20MHz
1 0 40MHz
1 1 25MHz
The value of HT_XTAL_FSEL is bootstrapped by pulling
ESW_P4_LED_0 and ESW_P3_LED_0 up or down accordingly,
but:
if a 40MHz crystal has been selected and
the ESW_P3_LED_0 pin is high during reset,
or a 20MHz crystal has been selected and
the ESW_P4_LED_0 pin is high during reset,
then the value of HT_XTAL_FSEL will indicate
that a 25MHz crystal is present.
By default, the state of the LED pins is PHY controlled
to reflect the link state.
To illustrate, if a board has:
5 ports with active low LED control,
and HT_XTAL_FSEL bootstrapped for 40MHz.
When the MT7530 is powered up without any external
connection, only the LED associated with Port 3 is
illuminated as ESW_P3_LED_0 is low.
In this state, directly after mt7530_setup()'s reset
is performed, the HWTRAP register (0x7800) reflects
the intended HT_XTAL_FSEL (HWTRAP bits 10:9) of 40MHz:
mt7530-mdio mdio-bus:1f: mt7530_read: 00007800 == 00007dcf
>>> bin(0x7dcf >> 9 & 0b11)
'0b10'
But if a cable is connected to Port 3 and the link
is active before mt7530_setup()'s reset takes place,
then HT_XTAL_FSEL seems to be set for 25MHz:
mt7530-mdio mdio-bus:1f: mt7530_read: 00007800 == 00007fcf
>>> bin(0x7fcf >> 9 & 0b11)
'0b11'
Once HT_XTAL_FSEL reflects 25MHz, none of the ports
are functional until the MT7621 (or MT7530 itself)
is reset.
By disabling the LED pins just before reset, the chance
of an unintended HT_XTAL_FSEL value is reduced.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Link: https://lore.kernel.org/r/20240305043952.21590-1-justin.swartz@risingedge.co.za
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the Marvell 88e6185 PCS driver to use neg_mode rather than the
mode argument to match the other updated PCS drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rhosE-003yuc-FM@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver has two separate reset sequence in different places:
- gpio/HW reset on start of ksz_switch_register()
- SW reset on start of ksz_setup()
The second one will overwrite drive strength configuration made in the
ksz_switch_register().
To fix it, move ksz_parse_drive_strength() from ksz_switch_register() to
ksz_setup().
Fixes: d67d7247f6 ("net: dsa: microchip: Add drive strength configuration")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240304135612.814404-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This bug was noticed while re-implementing parts of the kernel
driver in userspace using spidev. The goal was to enable some
of the errata workarounds that Microchip describes in their
errata sheet [1].
Both the errata sheet and the regular datasheet of e.g. the KSZ8795
imply that you need to do this for indirect register accesses:
- write a 16-bit value to a control register pair (this value
consists of the indirect register table, and the offset inside
the table)
- either read or write an 8-bit value from the data storage
register (indicated by REG_IND_BYTE in the kernel)
The current implementation has the order swapped. It can be
proven, by reading back some indirect register with known content
(the EEE register modified in ksz8_handle_global_errata() is one of
these), that this implementation does not work.
Private discussion with Oleksij Rempel of Pengutronix has revealed
that the workaround was apparantly never tested on actual hardware.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/Errata/KSZ87xx-Errata-DS80000687C.pdf
Signed-off-by: Tobias Jakobi (Compleo) <tobias.jakobi.compleo@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 7b6e6235b6 ("net: dsa: microchip: ksz8795: handle eee specif erratum")
Link: https://lore.kernel.org/r/20240304154135.161332-1-tobias.jakobi.compleo@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "MT7621 Giga Switch Programming Guide v0.3", "MT7531 Reference Manual
for Development Board v1.0", and "MT7988A Wi-Fi 7 Generation Router
Platform: Datasheet (Open Version) v0.1" documents show that these bits are
enabled at reset:
PMCR_IFG_XMIT(1) (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_MAC_MODE (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_TX_EN
PMCR_RX_EN
PMCR_BACKOFF_EN (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_BACKPR_EN (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_TX_FC_EN
PMCR_RX_FC_EN
These bits also don't exist on the MT7530_PMCR_P(6) register of the switch
on the MT7988 SoC:
PMCR_IFG_XMIT()
PMCR_MAC_MODE
PMCR_BACKOFF_EN
PMCR_BACKPR_EN
Remove the setting of the bits not part of PMCR_LINK_SETTINGS_MASK on
phylink_mac_config as they're already set.
The bit for setting the port on force mode is already done on
mt7530_setup() and mt7531_setup_common(). So get rid of
PMCR_FORCE_MODE_ID() which helped determine which bit to use for the switch
model.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
port_enable and port_disable clears the link settings. Move that to
mt7530_setup() and mt7531_setup_common() which set up the switches. This
way, the link settings are cleared on all ports at setup, and then only
once with phylink_mac_link_down() when a link goes down.
Enable force mode at setup to apply the force part of the link settings.
This ensures that disabled ports will have their link down.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The commit fae4630840 ("net: dsa: mt753x: fix pcs conversion regression")
fixes regression caused by cpu_port_config manually calling phylink
operations. cpu_port_config was deemed useless and was removed. Therefore,
put initialising PCS devices code back to its original order.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Oleksij Rempel