Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py
75cc19c8ff ("selftests: drv-net: add xdp cases for ping.py")
de94e86974 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c
a70f891e0f ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()")
1d22d3060b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile
6f50175cca ("selftests: Add IPv6 link-local address generation tests for GRE devices.")
2e5584e0f9 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c
661958552e ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
fe96d717d3 ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ATU Load operations could fail silently if there's not enough space
on the device to hold the new entry. When this happens, the symptom
depends on the unknown flood settings. If unknown multicast flood is
disabled, the multicast packets are dropped when the ATU table is
full. If unknown multicast flood is enabled, the multicast packets
will be flooded to all ports. Either way, IGMP snooping is broken
when the ATU Load operation fails silently.
Do a Read-After-Write verification after each fdb/mdb add operation
to make sure that the operation was really successful, and return
-ENOSPC otherwise.
Fixes: defb05b9b9 ("net: dsa: mv88e6xxx: Add support for fdb_add, fdb_del, and fdb_getnext")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250306172306.3859214-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
net/ethtool/cabletest.c
2bcf4772e4 ("net: ethtool: try to protect all callback with netdev instance lock")
637399bf7e ("net: ethtool: netlink: Allow NULL nlattrs when getting a phy_device")
No Adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On MMIO devices (e.g. MT7988 or EN7581) unicast traffic received on lanX
port is flooded on all other user ports if the DSA switch is configured
without VLAN support since PORT_MATRIX in PCR regs contains all user
ports. Similar to MDIO devices (e.g. MT7530 and MT7531) fix the issue
defining default VLAN-ID 0 for MT7530 MMIO devices.
Fixes: 110c18bfed ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/20250304-mt7988-flooding-fix-v1-1-905523ae83e9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the custom IRQ chip handler and mask/unmask functions with
REGMAP_IRQ. This significantly simplifies the code and allows for the
removal of almost all interrupt-related functions from mt7530.c.
Tested on MT7988A built-in switch (MMIO) as well as MT7531AE IC (MDIO).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/221013c3530b61504599e285c341a993f6188f00.1740792674.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Packet Processor Engine (PPE) module used for hw acceleration on EN7581
mac block, in order to properly parse packets, requires DSA untagged
packets on TX side and read DSA tag from DMA descriptor on RX side.
For this reason, enable RX Special Tag (SPTAG) for EN7581 SoC.
This is a preliminary patch to enable netfilter flowtable hw offloading
on EN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make NET_DSA_REALTEK_RTL8366RB_LEDS a hidden symbol.
It seems very unlikely user would want to intentionally
disable it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250228004534.3428681-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When the kernel is compiled without LED framework support the
rtl8366rb fails to build like this:
rtl8366rb.o: in function `rtl8366rb_setup_led':
rtl8366rb.c:953:(.text.unlikely.rtl8366rb_setup_led+0xe8):
undefined reference to `led_init_default_state_get'
rtl8366rb.c:980:(.text.unlikely.rtl8366rb_setup_led+0x240):
undefined reference to `devm_led_classdev_register_ext'
As this is constantly coming up in different randconfig builds,
bite the bullet and create a separate file for the offending
code, split out a header with all stuff needed both in the
core driver and the leds code.
Add a new bool Kconfig option for the LED compile target, such
that it depends on LEDS_CLASS=y || LEDS_CLASS=RTL8366RB
which make LED support always available when LEDS_CLASS is
compiled into the kernel and enforce that if the LEDS_CLASS
is a module, then the RTL8366RB driver needs to be a module
as well so that modprobe can resolve the dependencies.
Fixes: 32d6170054 ("net: dsa: realtek: add LED drivers for rtl8366rb")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202502070525.xMUImayb-lkp@intel.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM53101 is a ethernet switch, very similar to the BCM53115.
Enable support for it, in the existing b53 dsa driver.
Signed-off-by: Torben Nielsen <torben.nielsen@prevas.dk>
Signed-off-by: Claus Stovgaard <claus.stovgaard@prevas.dk>
Link: https://patch.msgid.link/20250217080503.1390282-1-claus.stovgaard@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As all PCS are using the neg_mode parameter rather than the legacy
an_mode, remove the ability to use the legacy an_mode. We remove the
tests in the phylink code, unconditionally passing the PCS neg_mode
parameter to PCS methods, and remove setting the flag from drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tidPn-0040hd-2R@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert mt7530 to use phylink managed EEE. When enabling EEE, we set
both PMCR_FORCE_EEE1G and PMCR_FORCE_EEE100 irrespective of the speed,
and clear them both when disabling.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1thR9q-003vXI-Cp@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the helper of_get_available_child_by_name() to simplify
sja1105_mdiobus_register().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify a5psw_probe() by using of_get_available_child_by_name().
While at it, move of_node_put(mdio) inside the if block to avoid code
duplication.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core
----
- More core refactoring to reduce the RTNL lock contention,
including preparatory work for the per-network namespace RTNL lock,
replacing RTNL lock with a per device-one to protect NAPI-related
net device data and moving synchronize_net() calls outside such
lock.
- Extend drop reasons usage, adding net scheduler, AF_UNIX, bridge and
more specific TCP coverage.
- Reduce network namespace tear-down time by removing per-subsystems
synchronize_net() in tipc and sched.
- Add flow label selector support for fib rules, allowing traffic
redirection based on such header field.
Netfilter
---------
- Do not remove netdev basechain when last device is gone, allowing
netdev basechains without devices.
- Revisit the flowtable teardown strategy, dealing better with fin,
reset and re-open events.
- Scale-up IP-vs connection dumping by avoiding linear search on
each restart.
Protocols
---------
- A significant XDP socket refactor, consolidating and optimizing
several helpers into the core
- Better scaling of ICMP rate-limiting, by removing false-sharing in
inet peers handling.
- Introduces netlink notifications for multicast IPv4 and IPv6
address changes.
- Add ipsec support for IP-TFS/AggFrag encapsulation, allowing
aggregation and fragmentation of the inner IP.
- Add sysctl to configure TIME-WAIT reuse delay for TCP sockets,
to avoid local port exhaustion issues when the average connection
lifetime is very short.
- Support updating keys (re-keying) for connections using kernel
TLS (for TLS 1.3 only).
- Support ipv4-mapped ipv6 address clients in smc-r v2.
- Add support for jumbo data packet transmission in RxRPC sockets,
gluing multiple data packets in a single UDP packet.
- Support RxRPC RACK-TLP to manage packet loss and retransmission in
conjunction with the congestion control algorithm.
Driver API
----------
- Introduce a unified and structured interface for reporting PHY
statistics, exposing consistent data across different H/W via
ethtool.
- Make timestamping selectable, allow the user to select the desired
hwtstamp provider (PHY or MAC) administratively.
- Add support for configuring a header-data-split threshold (HDS)
value via ethtool, to deal with partial or buggy H/W implementation.
- Consolidate DSA drivers Energy Efficiency Ethernet support.
- Add EEE management to phylink, making use of the phylib
implementation.
- Add phylib support for in-band capabilities negotiation.
- Simplify how phylib-enabled mac drivers expose the supported
interfaces.
Tests and tooling
-----------------
- Make the YNL tool package-friendly to make it easier to deploy it
separately from the kernel.
- Increase TCP selftest coverage importing several packetdrill
test-cases.
- Regenerate the ethtool uapi header from the YNL spec,
to ease maintenance and future development.
- Add YNL support for decoding the link types used in net
self-tests, allowing a single build to run both net and
drivers/net.
Drivers
-------
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- add cross E-Switch QoS support
- add SW Steering support for ConnectX-8
- implement support for HW-Managed Flow Steering, improving the
rule deletion/insertion rate
- support for multi-host LAG
- Intel (ixgbe, ice, igb):
- ice: add support for devlink health events
- ixgbe: add initial support for E610 chipset variant
- igb: add support for AF_XDP zero-copy
- Meta:
- add support for basic RSS config
- allow changing the number of channels
- add hardware monitoring support
- Broadcom (bnxt):
- implement TCP data split and HDS threshold ethtool support,
enabling Device Memory TCP.
- Marvell Octeon:
- implement egress ipsec offload support for the cn10k family
- Hisilicon (HIBMC):
- implement unicast MAC filtering
- Ethernet NICs embedded and virtual:
- Convert UDP tunnel drivers to NETDEV_PCPU_STAT_DSTATS, avoiding
contented atomic operations for drop counters
- Freescale:
- quicc: phylink conversion
- enetc: support Tx and Rx checksum offload and improve TSO
performances
- MediaTek:
- airoha: introduce support for ETS and HTB Qdisc offload
- Microchip:
- lan78XX USB: preparation work for phylink conversion
- Synopsys (stmmac):
- support DWMAC IP on NXP Automotive SoCs S32G2xx/S32G3xx/S32R45
- refactor EEE support to leverage the new driver API
- optimize DMA and cache access to increase raw RX performances
by 40%
- TI:
- icssg-prueth: add multicast filtering support for VLAN
interface
- netkit:
- add ability to configure head/tailroom
- VXLAN:
- accepts packets with user-defined reserved bit
- Ethernet switches:
- Microchip:
- lan969x: add RGMII support
- lan969x: improve TX and RX performance using the FDMA engine
- nVidia/Mellanox:
- move Tx header handling to PCI driver, to ease XDP support
- Ethernet PHYs:
- Texas Instruments DP83822:
- add support for GPIO2 clock output
- Realtek:
- 8169: add support for RTL8125D rev.b
- rtl822x: add hwmon support for the temperature sensor
- Microchip:
- add support for RDS PTP hardware
- consolidate periodic output signal generation
- CAN:
- several DT-bindings to DT schema conversions
- tcan4x5x:
- add HW standby support
- support nWKRQ voltage selection
- kvaser:
- allowing Bus Error Reporting runtime configuration
- WiFi:
- the on-going Multi-Link Operation (MLO) effort continues, affecting
both the stack and in drivers
- mac80211/cfg80211:
- Emergency Preparedness Communication Services (EPCS) station mode
support
- support for adding and removing station links for MLO
- add support for WiFi 7/EHT mesh over 320 MHz channels
- report Tx power info for each link
- RealTek (rtw88):
- enable USB Rx aggregation and USB 3 to improve performance
- LED support
- RealTek (rtw89):
- refactor power save to support Multi-Link Operations
- add support for RTL8922AE-VS variant
- MediaTek (mt76):
- single wiphy multiband support (preparation for MLO)
- p2p device support
- add TP-Link TXE50UH USB adapter support
- Qualcomm (ath10k):
- support for the QCA6698AQ IP core
- Qualcomm (ath12k):
- enable MLO for QCN9274
- Bluetooth:
- Allow sysfs to trigger hdev reset, to allow recovering devices
not responsive from user-space
- MediaTek: add support for MT7922, MT7925, MT7921e devices
- Realtek: add support for RTL8851BE devices
- Qualcomm: add support for WCN785x devices
- ISO: allow BIG re-sync
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=hrsp
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"This is slightly smaller than usual, with the most interesting work
being still around RTNL scope reduction.
Core:
- More core refactoring to reduce the RTNL lock contention, including
preparatory work for the per-network namespace RTNL lock, replacing
RTNL lock with a per device-one to protect NAPI-related net device
data and moving synchronize_net() calls outside such lock.
- Extend drop reasons usage, adding net scheduler, AF_UNIX, bridge
and more specific TCP coverage.
- Reduce network namespace tear-down time by removing per-subsystems
synchronize_net() in tipc and sched.
- Add flow label selector support for fib rules, allowing traffic
redirection based on such header field.
Netfilter:
- Do not remove netdev basechain when last device is gone, allowing
netdev basechains without devices.
- Revisit the flowtable teardown strategy, dealing better with fin,
reset and re-open events.
- Scale-up IP-vs connection dumping by avoiding linear search on each
restart.
Protocols:
- A significant XDP socket refactor, consolidating and optimizing
several helpers into the core
- Better scaling of ICMP rate-limiting, by removing false-sharing in
inet peers handling.
- Introduces netlink notifications for multicast IPv4 and IPv6
address changes.
- Add ipsec support for IP-TFS/AggFrag encapsulation, allowing
aggregation and fragmentation of the inner IP.
- Add sysctl to configure TIME-WAIT reuse delay for TCP sockets, to
avoid local port exhaustion issues when the average connection
lifetime is very short.
- Support updating keys (re-keying) for connections using kernel TLS
(for TLS 1.3 only).
- Support ipv4-mapped ipv6 address clients in smc-r v2.
- Add support for jumbo data packet transmission in RxRPC sockets,
gluing multiple data packets in a single UDP packet.
- Support RxRPC RACK-TLP to manage packet loss and retransmission in
conjunction with the congestion control algorithm.
Driver API:
- Introduce a unified and structured interface for reporting PHY
statistics, exposing consistent data across different H/W via
ethtool.
- Make timestamping selectable, allow the user to select the desired
hwtstamp provider (PHY or MAC) administratively.
- Add support for configuring a header-data-split threshold (HDS)
value via ethtool, to deal with partial or buggy H/W
implementation.
- Consolidate DSA drivers Energy Efficiency Ethernet support.
- Add EEE management to phylink, making use of the phylib
implementation.
- Add phylib support for in-band capabilities negotiation.
- Simplify how phylib-enabled mac drivers expose the supported
interfaces.
Tests and tooling:
- Make the YNL tool package-friendly to make it easier to deploy it
separately from the kernel.
- Increase TCP selftest coverage importing several packetdrill
test-cases.
- Regenerate the ethtool uapi header from the YNL spec, to ease
maintenance and future development.
- Add YNL support for decoding the link types used in net self-tests,
allowing a single build to run both net and drivers/net.
Drivers:
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- add cross E-Switch QoS support
- add SW Steering support for ConnectX-8
- implement support for HW-Managed Flow Steering, improving the
rule deletion/insertion rate
- support for multi-host LAG
- Intel (ixgbe, ice, igb):
- ice: add support for devlink health events
- ixgbe: add initial support for E610 chipset variant
- igb: add support for AF_XDP zero-copy
- Meta:
- add support for basic RSS config
- allow changing the number of channels
- add hardware monitoring support
- Broadcom (bnxt):
- implement TCP data split and HDS threshold ethtool support,
enabling Device Memory TCP.
- Marvell Octeon:
- implement egress ipsec offload support for the cn10k family
- Hisilicon (HIBMC):
- implement unicast MAC filtering
- Ethernet NICs embedded and virtual:
- Convert UDP tunnel drivers to NETDEV_PCPU_STAT_DSTATS, avoiding
contented atomic operations for drop counters
- Freescale:
- quicc: phylink conversion
- enetc: support Tx and Rx checksum offload and improve TSO
performances
- MediaTek:
- airoha: introduce support for ETS and HTB Qdisc offload
- Microchip:
- lan78XX USB: preparation work for phylink conversion
- Synopsys (stmmac):
- support DWMAC IP on NXP Automotive SoCs S32G2xx/S32G3xx/S32R45
- refactor EEE support to leverage the new driver API
- optimize DMA and cache access to increase raw RX performances
by 40%
- TI:
- icssg-prueth: add multicast filtering support for VLAN
interface
- netkit:
- add ability to configure head/tailroom
- VXLAN:
- accepts packets with user-defined reserved bit
- Ethernet switches:
- Microchip:
- lan969x: add RGMII support
- lan969x: improve TX and RX performance using the FDMA engine
- nVidia/Mellanox:
- move Tx header handling to PCI driver, to ease XDP support
- Ethernet PHYs:
- Texas Instruments DP83822:
- add support for GPIO2 clock output
- Realtek:
- 8169: add support for RTL8125D rev.b
- rtl822x: add hwmon support for the temperature sensor
- Microchip:
- add support for RDS PTP hardware
- consolidate periodic output signal generation
- CAN:
- several DT-bindings to DT schema conversions
- tcan4x5x:
- add HW standby support
- support nWKRQ voltage selection
- kvaser:
- allowing Bus Error Reporting runtime configuration
- WiFi:
- the on-going Multi-Link Operation (MLO) effort continues,
affecting both the stack and in drivers
- mac80211/cfg80211:
- Emergency Preparedness Communication Services (EPCS) station
mode support
- support for adding and removing station links for MLO
- add support for WiFi 7/EHT mesh over 320 MHz channels
- report Tx power info for each link
- RealTek (rtw88):
- enable USB Rx aggregation and USB 3 to improve performance
- LED support
- RealTek (rtw89):
- refactor power save to support Multi-Link Operations
- add support for RTL8922AE-VS variant
- MediaTek (mt76):
- single wiphy multiband support (preparation for MLO)
- p2p device support
- add TP-Link TXE50UH USB adapter support
- Qualcomm (ath10k):
- support for the QCA6698AQ IP core
- Qualcomm (ath12k):
- enable MLO for QCN9274
- Bluetooth:
- Allow sysfs to trigger hdev reset, to allow recovering devices
not responsive from user-space
- MediaTek: add support for MT7922, MT7925, MT7921e devices
- Realtek: add support for RTL8851BE devices
- Qualcomm: add support for WCN785x devices
- ISO: allow BIG re-sync"
* tag 'net-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1386 commits)
net/rose: prevent integer overflows in rose_setsockopt()
net: phylink: fix regression when binding a PHY
net: ethernet: ti: am65-cpsw: streamline TX queue creation and cleanup
net: ethernet: ti: am65-cpsw: streamline RX queue creation and cleanup
net: ethernet: ti: am65-cpsw: ensure proper channel cleanup in error path
ipv6: Convert inet6_rtm_deladdr() to per-netns RTNL.
ipv6: Convert inet6_rtm_newaddr() to per-netns RTNL.
ipv6: Move lifetime validation to inet6_rtm_newaddr().
ipv6: Set cfg.ifa_flags before device lookup in inet6_rtm_newaddr().
ipv6: Pass dev to inet6_addr_add().
ipv6: Convert inet6_ioctl() to per-netns RTNL.
ipv6: Hold rtnl_net_lock() in addrconf_init() and addrconf_cleanup().
ipv6: Hold rtnl_net_lock() in addrconf_dad_work().
ipv6: Hold rtnl_net_lock() in addrconf_verify_work().
ipv6: Convert net.ipv6.conf.${DEV}.XXX sysctl to per-netns RTNL.
ipv6: Add __in6_dev_get_rtnl_net().
net: stmmac: Drop redundant skb_mark_for_recycle() for SKB frags
net: mii: Fix the Speed display when the network cable is not connected
sysctl net: Remove macro checks for CONFIG_SYSCTL
eth: bnxt: update header sizing defaults
...
1) Per-CPU kthreads must stay affine to a single CPU and never execute
relevant code on any other CPU. This is currently handled by smpboot
code which takes care of CPU-hotplug operations. Affinity here is
a correctness constraint.
2) Some kthreads _have_ to be affine to a specific set of CPUs and can't
run anywhere else. The affinity is set through kthread_bind_mask()
and the subsystem takes care by itself to handle CPU-hotplug
operations. Affinity here is assumed to be a correctness constraint.
3) Per-node kthreads _prefer_ to be affine to a specific NUMA node. This
is not a correctness constraint but merely a preference in terms of
memory locality. kswapd and kcompactd both fall into this category.
The affinity is set manually like for any other task and CPU-hotplug
is supposed to be handled by the relevant subsystem so that the task
is properly reaffined whenever a given CPU from the node comes up.
Also care should be taken so that the node affinity doesn't cross
isolated (nohz_full) cpumask boundaries.
4) Similar to the previous point except kthreads have a _preferred_
affinity different than a node. Both RCU boost kthreads and RCU
exp kworkers fall into this category as they refer to "RCU nodes"
from a distinctly distributed tree.
Currently the preferred affinity patterns (3 and 4) have at least 4
identified users, with more or less success when it comes to handle
CPU-hotplug operations and CPU isolation. Each of which do it in its own
ad-hoc way.
This is an infrastructure proposal to handle this with the following API
changes:
_ kthread_create_on_node() automatically affines the created kthread to
its target node unless it has been set as per-cpu or bound with
kthread_bind[_mask]() before the first wake-up.
- kthread_affine_preferred() is a new function that can be called right
after kthread_create_on_node() to specify a preferred affinity
different than the specified node.
When the preferred affinity can't be applied because the possible
targets are offline or isolated (nohz_full), the kthread is affine
to the housekeeping CPUs (which means to all online CPUs most of the
time or only the non-nohz_full CPUs when nohz_full= is set).
kswapd, kcompactd, RCU boost kthreads and RCU exp kworkers have been
converted, along with a few old drivers.
Summary of the changes:
* Consolidate a bunch of ad-hoc implementations of kthread_run_on_cpu()
* Introduce task_cpu_fallback_mask() that defines the default last
resort affinity of a task to become nohz_full aware
* Add some correctness check to ensure kthread_bind() is always called
before the first kthread wake up.
* Default affine kthread to its preferred node.
* Convert kswapd / kcompactd and remove their halfway working ad-hoc
affinity implementation
* Implement kthreads preferred affinity
* Unify kthread worker and kthread API's style
* Convert RCU kthreads to the new API and remove the ad-hoc affinity
implementation.
-----BEGIN PGP SIGNATURE-----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=g8In
-----END PGP SIGNATURE-----
Merge tag 'kthread-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks
Pull kthread updates from Frederic Weisbecker:
"Kthreads affinity follow either of 4 existing different patterns:
1) Per-CPU kthreads must stay affine to a single CPU and never
execute relevant code on any other CPU. This is currently handled
by smpboot code which takes care of CPU-hotplug operations.
Affinity here is a correctness constraint.
2) Some kthreads _have_ to be affine to a specific set of CPUs and
can't run anywhere else. The affinity is set through
kthread_bind_mask() and the subsystem takes care by itself to
handle CPU-hotplug operations. Affinity here is assumed to be a
correctness constraint.
3) Per-node kthreads _prefer_ to be affine to a specific NUMA node.
This is not a correctness constraint but merely a preference in
terms of memory locality. kswapd and kcompactd both fall into this
category. The affinity is set manually like for any other task and
CPU-hotplug is supposed to be handled by the relevant subsystem so
that the task is properly reaffined whenever a given CPU from the
node comes up. Also care should be taken so that the node affinity
doesn't cross isolated (nohz_full) cpumask boundaries.
4) Similar to the previous point except kthreads have a _preferred_
affinity different than a node. Both RCU boost kthreads and RCU
exp kworkers fall into this category as they refer to "RCU nodes"
from a distinctly distributed tree.
Currently the preferred affinity patterns (3 and 4) have at least 4
identified users, with more or less success when it comes to handle
CPU-hotplug operations and CPU isolation. Each of which do it in its
own ad-hoc way.
This is an infrastructure proposal to handle this with the following
API changes:
- kthread_create_on_node() automatically affines the created kthread
to its target node unless it has been set as per-cpu or bound with
kthread_bind[_mask]() before the first wake-up.
- kthread_affine_preferred() is a new function that can be called
right after kthread_create_on_node() to specify a preferred
affinity different than the specified node.
When the preferred affinity can't be applied because the possible
targets are offline or isolated (nohz_full), the kthread is affine to
the housekeeping CPUs (which means to all online CPUs most of the time
or only the non-nohz_full CPUs when nohz_full= is set).
kswapd, kcompactd, RCU boost kthreads and RCU exp kworkers have been
converted, along with a few old drivers.
Summary of the changes:
- Consolidate a bunch of ad-hoc implementations of
kthread_run_on_cpu()
- Introduce task_cpu_fallback_mask() that defines the default last
resort affinity of a task to become nohz_full aware
- Add some correctness check to ensure kthread_bind() is always
called before the first kthread wake up.
- Default affine kthread to its preferred node.
- Convert kswapd / kcompactd and remove their halfway working ad-hoc
affinity implementation
- Implement kthreads preferred affinity
- Unify kthread worker and kthread API's style
- Convert RCU kthreads to the new API and remove the ad-hoc affinity
implementation"
* tag 'kthread-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks:
kthread: modify kernel-doc function name to match code
rcu: Use kthread preferred affinity for RCU exp kworkers
treewide: Introduce kthread_run_worker[_on_cpu]()
kthread: Unify kthread_create_on_cpu() and kthread_create_worker_on_cpu() automatic format
rcu: Use kthread preferred affinity for RCU boost
kthread: Implement preferred affinity
mm: Create/affine kswapd to its preferred node
mm: Create/affine kcompactd to its preferred node
kthread: Default affine kthread to its preferred NUMA node
kthread: Make sure kthread hasn't started while binding it
sched,arm64: Handle CPU isolation on last resort fallback rq selection
arm64: Exclude nohz_full CPUs from 32bits el0 support
lib: test_objpool: Use kthread_run_on_cpu()
kallsyms: Use kthread_run_on_cpu()
soc/qman: test: Use kthread_run_on_cpu()
arm/bL_switcher: Use kthread_run_on_cpu()
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the linkage between the DSA user port ethtool_ops :: get_ts_info
and the implementation from the Ocelot switch library.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250116104628.123555-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass the current neg_mode into the .pcs_get_state() method. Update all
users of phylink PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1tXGeT-000Et3-4L@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
kthread_create() creates a kthread without running it yet. kthread_run()
creates a kthread and runs it.
On the other hand, kthread_create_worker() creates a kthread worker and
runs it.
This difference in behaviours is confusing. Also there is no way to
create a kthread worker and affine it using kthread_bind_mask() or
kthread_affine_preferred() before starting it.
Consolidate the behaviours and introduce kthread_run_worker[_on_cpu]()
that behaves just like kthread_run(). kthread_create_worker[_on_cpu]()
will now only create a kthread worker without starting it.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
mv88e6xxx_get_mac_eee() is no longer called by the core DSA code.
Remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tUllK-007Uz9-D7@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mt753x_get_mac_eee() is no longer called by the core DSA code. Remove
it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/E1tUllF-007Uz3-95@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dsa_user_get_eee() calls the DSA switch get_mac_eee() method followed
by phylink_ethtool_get_eee(), which goes on to call
phy_ethtool_get_eee(). This overwrites all members of the passed
ethtool_keee, which means anything written by the DSA switch
get_mac_eee() method will be discarded.
Remove setting any members in mt753x_get_mac_eee().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/E1tUlku-007Uyc-RP@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dsa_user_get_eee() calls the DSA switch get_mac_eee() method followed
by phylink_ethtool_get_eee(), which goes on to call
phy_ethtool_get_eee(). This overwrites all members of the passed
ethtool_keee, which means anything written by the DSA switch
get_mac_eee() method will be discarded.
Remove setting any members in ksz_get_mac_eee().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tUlkp-007UyW-OR@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PTP driver code only works for certain KSZ switches like KSZ9477,
KSZ9567, LAN937X and their varieties. This code is enabled by kernel
configuration CONFIG_NET_DSA_MICROCHIP_KSZ_PTP. As the DSA driver is
common to work with all KSZ switches this PTP code is not appropriate
for other unsupported switches. The ptp_capable indication is added to
the chip data structure to signal whether to execute those code.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/20241218020240.70601-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ DSA driver starts a timer to read MIB counters periodically to
avoid count overrun. During system suspend this will give an error for
not able to write to register as the SPI system returns an error when
it is in suspend state. This implementation stops the timer when the
system goes into suspend and restarts it when resumed.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218020311.70628-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The aging count is not a simple 20-bit value but comprises a 3-bit
multiplier and a 20-bit second time. The code tries to use the
original multiplier which is 4 as the second count is still 300 seconds
by default.
As the 20-bit number is now too large for practical use there is an option
to interpret it as microseconds instead of seconds.
Fixes: 2c119d9982 ("net: dsa: microchip: add the support for set_ageing_time")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218020224.70590-3-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The aging count is not a simple 11-bit value but comprises a 3-bit
multiplier and an 8-bit second count. The code tries to use the
original multiplier which is 4 as the second count is still 300 seconds
by default.
Fixes: 2c119d9982 ("net: dsa: microchip: add the support for set_ageing_time")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218020224.70590-2-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
wait_for_complete_timeout() expects a timeout in jiffies. With the
driver, some call sites converted QCA8K_ETHERNET_TIMEOUT to jiffies,
others did not. Make the code consistent by changes the #define to
include a call to msecs_to_jiffies, and remove all other calls to
msecs_to_jiffies.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: from Christian would be very welcome.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8d7ae22ae9 ("net: dsa: microchip: KSZ9477 register regmap
alignment to 32 bit boundaries") fixed an issue whereby regmap_reg_range
did not allow writes as 32 bit words to KSZ9477 PHY registers, this fix
for KSZ9896 is adapted from there as the same errata is present in
KSZ9896C as "Module 5: Certain PHY registers must be written as pairs
instead of singly" the explanation below is likewise taken from this
commit.
The commit provided code
to apply "Module 6: Certain PHY registers must be written as pairs instead
of singly" errata for KSZ9477 as this chip for certain PHY registers
(0xN120 to 0xN13F, N=1,2,3,4,5) must be accessed as 32 bit words instead
of 16 or 8 bit access.
Otherwise, adjacent registers (no matter if reserved or not) are
overwritten with 0x0.
Without this patch some registers (e.g. 0x113c or 0x1134) required for 32
bit access are out of valid regmap ranges.
As a result, following error is observed and KSZ9896 is not properly
configured:
ksz-switch spi1.0: can't rmw 32bit reg 0x113c: -EIO
ksz-switch spi1.0: can't rmw 32bit reg 0x1134: -EIO
ksz-switch spi1.0 lan1 (uninitialized): failed to connect to PHY: -EIO
ksz-switch spi1.0 lan1 (uninitialized): error -5 setting up PHY for tree 0, switch 0, port 0
The solution is to modify regmap_reg_range to allow accesses with 4 bytes
boundaries.
Fixes: 5c844d57aa ("net: dsa: microchip: fix writes to phy registers >= 0x10")
Signed-off-by: Jesse Van Gavere <jesse.vangavere@scioteq.com>
Link: https://patch.msgid.link/20241211092932.26881-1-jesse.vangavere@scioteq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by reusing the ksz_validate_eee()
method as a template, renaming the function, changing the return type
and values, and removing it from the ksz_set_mac_eee() and
ksz_get_mac_eee() methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14Z-006cZs-6o@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by using the generic helper as all
user ports support EEE.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14U-006cZm-2K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by using the generic helper as all
user ports support EEE.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14O-006cZg-VM@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by using the generic helper as all
user ports support EEE.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14J-006cZa-Rh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method to indicate that EEE is not
supported by two switch variants, rather than making these checks in
the .set_mac_eee() and .get_mac_eee() methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14E-006cZU-Nc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With this port schedule:
tc qdisc replace dev $send_if parent root handle 100 taprio \
num_tc 8 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
map 0 1 2 3 4 5 6 7 \
base-time 0 cycle-time 10000 \
sched-entry S 01 1250 \
sched-entry S 02 1250 \
sched-entry S 04 1250 \
sched-entry S 08 1250 \
sched-entry S 10 1250 \
sched-entry S 20 1250 \
sched-entry S 40 1250 \
sched-entry S 80 1250 \
flags 2
ptp4l would fail to take TX timestamps of Pdelay_Resp messages like this:
increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
ptp4l[4134.168]: port 2: send peer delay response failed
It turns out that the driver can't take their TX timestamps because it
can't transmit them in the first place. And there's nothing special
about the Pdelay_Resp packets - they're just regular 68 byte packets.
But with this taprio configuration, the switch would refuse to send even
the ETH_ZLEN minimum packet size.
This should have definitely not been the case. When applying the taprio
config, the driver prints:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
and thus, everything under 132 bytes - ETH_FCS_LEN should have been sent
without problems. Yet it's not.
For the forwarding path, the configuration is fine, yet packets injected
from Linux get stuck with this schedule no matter what.
The first hint that the static guard bands are the cause of the problem
is that reverting Michael Walle's commit 297c4de6f7 ("net: dsa: felix:
re-enable TAS guard band mode") made things work. It must be that the
guard bands are calculated incorrectly.
I remembered that there is a magic constant in the driver, set to 33 ns
for no logical reason other than experimentation, which says "never let
the static guard bands get so large as to leave less than this amount of
remaining space in the time slot, because the queue system will refuse
to schedule packets otherwise, and they will get stuck". I had a hunch
that my previous experimentally-determined value was only good for
packets coming from the forwarding path, and that the CPU injection path
needed more.
I came to the new value of 35 ns through binary search, after seeing
that with 544 ns (the bit time required to send the Pdelay_Resp packet
at gigabit) it works. Again, this is purely experimental, there's no
logic and the manual doesn't say anything.
The new driver prints for this schedule look like this:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
So yes, the maximum MTU is now even smaller by 1 byte than before.
This is maybe counter-intuitive, but makes more sense with a diagram of
one time slot.
Before:
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<----><---------------------------------------------->
33 ns 1217 ns static guard band
useful
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<-----><--------------------------------------------->
35 ns 1215 ns static guard band
useful
The static guard band implemented by this switch hardware directly
determines the maximum allowable MTU for that traffic class. The larger
it is, the earlier the switch will stop scheduling frames for
transmission, because otherwise they might overrun the gate close time
(and avoiding that is the entire purpose of Michael's patch).
So, we now have guard bands smaller by 2 ns, thus, in this particular
case, we lose a byte of the maximum MTU.
Fixes: 11afdc6526 ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20241210132640.3426788-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of the sanity checks in pack() and unpack() can be covered at
compile time. There is only one exception, and that is truncation of the
uval during a pack() operation.
We'd like the error-less __pack() to catch that condition as well. But
at the same time, it is currently the responsibility of consumer drivers
(currently just sja1105) to print anything at all when this error
occurs, and then discard the return code.
We can just print a loud warning in the library code and continue with
the truncated __pack() operation. In practice, having the warning is
very important, see commit 24deec6b9e ("net: dsa: sja1105: disallow
C45 transactions on the BASE-TX MDIO bus") where the bug was caught
exactly by noticing this print.
Add the first print to the packing library, and at the same time remove
the print for the same condition from the sja1105 driver, to avoid
double printing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241210-packing-pack-fields-and-ice-implementation-v10-2-ee56a47479ac@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Different families of switches have different statistics available.
This information is current hard coded into functions, however this
information will also soon be needed when getting statistics from the
RMU. Move it into the info structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241207-v6-13-rc1-net-next-mv88e6xxx-stats-refactor-v1-1-b9960f839846@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In configurations with 2 or more DSA clusters it will fail to allocate
unique MDIO bus names as only the switch ID is used, fix this by using
a combination of the tree ID and switch ID when needed
Signed-off-by: Jesse Van Gavere <jesse.vangavere@scioteq.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241206204202.649912-1-jesse.vangavere@scioteq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LAN9646 switch is a 6-port switch with functions like KSZ9897. It has
4 internal PHYs and 1 SGMII port. The chip id read from hardware is
same as KSZ9477, so software driver needs to create a new chip id and
group allowable functions under its chip data structure to
differentiate the product.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/20241109015705.82685-3-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
qca8k_phy_eth_command() is used to probe the child MDIO bus while the
parent MDIO is locked. This causes lockdep splat, reporting a possible
deadlock. It is not an actually deadlock, because different locks are
used. By making use of mutex_lock_nested() we can avoid this false
positive.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241110175955.3053664-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce ksz_parse_dt_phy_config() to validate and parse PHY
configuration from the device tree for KSZ switches. This function
ensures proper setup of internal PHYs by checking `phy-handle`
properties, verifying expected PHY IDs, and handling parent node
mismatches. Sets the PHY mask on the MII bus if validation is
successful. Returns -EINVAL on configuration errors.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241106075942.1636998-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement side MDIO channel support for LAN937x switches, providing an
alternative to SPI for PHY management alongside existing SPI-based
switch configuration. This is needed to reduce SPI load, as SPI can be
relatively expensive for small packets compared to MDIO support.
Also, implemented static mappings for PHY addresses for various LAN937x
models to support different internal PHY configurations. Since the PHY
address mappings are not equal to the port indexes, this patch also
provides PHY address calculation based on hardware strapping
configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace repeated cleanup code with a single error path using a label.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for accessing PHYs via a side MDIO interface in LAN937x
switches. The existing code already supports accessing PHYs via main
management interfaces, which can be SPI, I2C, or MDIO, depending on the
chip variant. This patch enables using a side MDIO bus, where SPI is
used for the main switch configuration and MDIO for managing the
integrated PHYs. On LAN937x, this is optional, allowing them to operate
in both configurations: SPI only, or SPI + MDIO. Typically, the SPI
interface is used for switch configuration, while MDIO handles PHY
management.
Additionally, update interrupt controller code to support non-linear
port to PHY address mapping, enabling correct interrupt handling for
configurations where PHY addresses do not directly correspond to port
indexes. This change ensures that the interrupt mechanism properly
aligns with the new, flexible PHY address mappings introduced by side
MDIO support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce port_setup_tc callback in mt7530 dsa driver in order to enable
dsa ports rate shaping via hw Token Bucket Filter (TBF) for hw switched
traffic.
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241031-mt7530-tc-offload-v2-1-cb242ad954a0@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These are the preferred way to copy ethtool strings.
Avoids incrementing pointers all over the place.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(for hellcreek driver)
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20241028044828.1639668-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'ports_fwnode' is initialized via device_get_named_child_node(), which
requires a call to fwnode_handle_put() when the variable is no longer
required to avoid leaking memory.
Add the missing fwnode_handle_put() after 'ports_fwnode' has been used
and is no longer required.
Fixes: 94a2a84f5e ("net: dsa: mv88e6xxx: Support LED control")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6393X family of devices can run its cycle counter off
an internal 250MHz clock instead of an external 125MHz one.
Add support for this cycle counter period by adding another set
of coefficients and lowering the periodic cycle counter read interval
to compensate for faster overflows at the increased frequency.
Otherwise, the PHC runs at 2x real time in userspace and cannot be
synchronized.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of relying on a fixed mapping of hardware family to cycle
counter frequency, pull this information from the
MV88E6XXX_TAI_CLOCK_PERIOD register.
This lets us support switches whose cycle counter frequencies depend on
board design.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of having them as individual fields in ptp_ops, wrap the
coefficients in a separate struct so they can be referenced together.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The well-known errata regarding EEE not being functional on various KSZ
switches has been refactored a few times. Recently the refactoring has
excluded several switches that the errata should also apply to.
Disable EEE for additional switches with this errata and provide
additional comments referring to the public errata document.
The original workaround for the errata was applied with a register
write to manually disable the EEE feature in MMD 7:60 which was being
applied for KSZ9477/KSZ9897/KSZ9567 switch ID's.
Then came commit 26dd2974c5 ("net: phy: micrel: Move KSZ9477 errata
fixes to PHY driver") and commit 6068e6d7ba ("net: dsa: microchip:
remove KSZ9477 PHY errata handling") which moved the errata from the
switch driver to the PHY driver but only for PHY_ID_KSZ9477 (PHY ID)
however that PHY code was dead code because an entry was never added
for PHY_ID_KSZ9477 via MODULE_DEVICE_TABLE.
This was apparently realized much later and commit 54a4e5c163 ("net:
phy: micrel: add Microchip KSZ 9477 to the device table") added the
PHY_ID_KSZ9477 to the PHY driver but as the errata was only being
applied to PHY_ID_KSZ9477 it's not completely clear what switches
that relates to.
Later commit 6149db4997 ("net: phy: micrel: fix KSZ9477 PHY issues
after suspend/resume") breaks this again for all but KSZ9897 by only
applying the errata for that PHY ID.
Following that this was affected with commit 08c6d8bae48c("net: phy:
Provide Module 4 KSZ9477 errata (DS80000754C)") which removes
the blatant register write to MMD 7:60 and replaces it by
setting phydev->eee_broken_modes = -1 so that the generic phy-c45 code
disables EEE but this is only done for the KSZ9477_CHIP_ID (Switch ID).
Lastly commit 0411f73c13 ("net: dsa: microchip: disable EEE for
KSZ8567/KSZ9567/KSZ9896/KSZ9897.") adds some additional switches
that were missing to the errata due to the previous changes.
This commit adds an additional set of switches.
Fixes: 0411f73c13 ("net: dsa: microchip: disable EEE for KSZ8567/KSZ9567/KSZ9896/KSZ9897.")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241018160658.781564-1-tharvey@gateworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cross-merge networking fixes after downstream PR (net-6.12-rc4).
Conflicts:
107a034d5c ("net/mlx5: qos: Store rate groups in a qos domain")
1da9cfd6c4 ("net/mlx5: Unregister notifier on eswitch init failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
mv88e6393x_port_set_policy doesn't correctly shift the ptr value when
converting the policy format between the old and new styles, so the
target register ends up with the ptr being written over the data bits.
Shift the pointer to align with the format expected by
mv88e6393x_port_policy_write().
Fixes: 6584b26020 ("net: dsa: mv88e6xxx: implement .port_set_policy for Amethyst")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241016040822.3917-1-peter@rashleigh.ca>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Rather than returning an EOPNOTSUPP error pointer when the switch
has no support for PCS, return NULL to indicate that no PCS is
required.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Similar to the situation described for sja1105 in commit 1f9fc48fd3
("net: dsa: sja1105: fix reception from VLAN-unaware bridges"), the
vsc73xx driver uses tag_8021q and doesn't need the ds->untag_bridge_pvid
request. In fact, this option breaks packet reception.
The ds->untag_bridge_pvid option strips VLANs from packets received on
VLAN-unaware bridge ports. But those VLANs should already be stripped
by tag_vsc73xx_8021q.c as part of vsc73xx_rcv() - they are not VLANs in
VLAN-unaware mode, but DSA tags. Thus, dsa_software_vlan_untag() tries
to untag a VLAN that doesn't exist, corrupting the packet.
Fixes: 93e4649efa ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20241014153041.1110364-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the Marvell datasheet the 88E6361 has two VTU pages
(4k VIDs per page) so the max_vid should be 8191, not 4095.
In the current implementation mv88e6xxx_vtu_walk() gives unexpected
results because of this error. I verified that mv88e6xxx_vtu_walk()
works correctly on the MV88E6361 with this patch in place.
Fixes: 12899f2998 ("net: dsa: mv88e6xxx: enable support for 88E6361 switch")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241014204342.5852-1-peter@rashleigh.ca
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prior to this patch ksz_ptp_msg_irq_setup() uses snprintf() to copy
strings. It does so by passing strings as the format argument of
snprintf(). This appears to be safe, due to the absence of format
specifiers in the strings, which are declared within the same function.
But nonetheless GCC 14 warns about it:
.../ksz_ptp.c:1109:55: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
1109 | snprintf(ptpmsg_irq->name, sizeof(ptpmsg_irq->name), name[n]);
| ^~~~~~~
.../ksz_ptp.c:1109:55: note: treat the string as an argument to avoid this
1109 | snprintf(ptpmsg_irq->name, sizeof(ptpmsg_irq->name), name[n]);
| ^
| "%s",
As what we are really dealing with here is a string copy, it seems make
sense to use a function designed for this purpose. In this case null
padding is not required, so strscpy is appropriate. And as the
destination is an array of fixed size, the 2-argument variant may be used.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241014-string-thing-v2-1-b9b29625060a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The err value in mv88e6xxx_region_atu_snapshot is now potentially
uninitialised on return. Initialise err as 0.
Fixes: ada5c3229b ("net: dsa: mv88e6xxx: Add FID map cache")
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241009212319.1045176-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a cached FID bitmap. This mitigates the need to walk all VTU entries
to find the next free FID.
When flushing the VTU (during init), zero the FID bitmap. Use and
manipulate this bitmap from now on, instead of reading HW for the FID
map.
The repeated VTU walks are costly and can take ~40 mins if ~4000 vlans
are added. Caching the FID map reduces this time to <2 mins.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241006212905.3142976-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All modern chips support and need the 10_100 bit set for supporting jumbo
frames on 10/100 ports, so instead of enabling it only for 583XX enable
it for everything except bcm63xx, where the bit is writeable, but does
nothing.
Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds
without the bit set.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
While BCM5325/5365 do not support jumbo frames, they do support slightly
oversized frames, so do not error out if requesting a supported MTU for
them.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
BCM5325/BCM5365 do not support jumbo frames, so we should not report a
jumbo frame mtu for them. But they do support so called "oversized"
frames up to 1536 bytes long by default, so report an appropriate MTU.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Accessing device registers seems to be not reliable, the chip
revision is sometimes detected wrongly (0 instead of expected 1).
Ensure that the chip reset is performed via reset GPIO and then
wait for 'Device Ready' status in HW_CFG register before doing
any register initializations.
Cc: stable@vger.kernel.org
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
[alex: reworked using read_poll_timeout()]
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20241004113655.3436296-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/dsa to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/36da477cb9fa0bffec32d50c2cf3d18e94a0e7e3.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SF2 crossbar register is a packed bitfield, giving the index of the
external port selected for each of the internal ports. On BCM4908 (the
only currently-supported switch family with a crossbar), there are 2
internal ports and 3 external ports, so there are 2 bits per internal
port.
The driver currently conflates the "bits per port" and "number of ports"
concepts, lumping both into the `num_crossbar_int_ports` field. Since it
is currently only possible for either of these counts to have a value of
2, there is no behavioral error resulting from this situation for now.
Make the code more readable (and support the future possibility of
larger crossbars) by adding a `num_crossbar_ext_bits` field to represent
the "bits per port" count and relying on this where appropriate instead.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241003212301.1339647-1-CFSworks@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds control over the hardware LEDs in the Marvell
MV88E6xxx DSA switch and enables it for MV88E6352.
This fixes an imminent problem on the Inteno XG6846 which
has a WAN LED that simply do not work with hardware
defaults: driver amendment is necessary.
The patch is modeled after Christian Marangis LED support
code for the QCA8k DSA switch, I got help with the register
definitions from Tim Harvey.
After this patch it is possible to activate hardware link
indication like this (or with a similar script):
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link
This makes the green link indicator come up on any link
speed. It is also possible to be more elaborate, like this:
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link_1000
cd /sys/class/leds/Marvell\ 88E6352:05:01:amber:wan/
echo netdev > trigger
echo 1 > link_100
Making the green LED come on for a gigabit link and the
amber LED come on for a 100 mbit link.
Each port has 2 LED slots (the hardware may use just one or
none) and the hardware triggers are specified in four bits per
LED, and some of the hardware triggers are only available on the
SFP (fiber) uplink. The restrictions are described in the
port.h header file where the registers are described. For
example, selector 1 set for LED 1 on port 5 or 6 will indicate
Fiber 1000 (gigabit) and activity with a blinking LED, but
ONLY for an SFP connection. If port 5/6 is used with something
not SFP, this selector is a noop: something else need to be
selected.
After the previous series rewriting the MV88E6xxx DT
bindings to use YAML a "leds" subnode is already valid
for each port, in my scratch device tree it looks like
this:
leds {
#address-cells = <1>;
#size-cells = <0>;
led@0 {
reg = <0>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_LAN;
default-state = "off";
linux,default-trigger = "netdev";
};
led@1 {
reg = <1>;
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_LAN;
default-state = "off";
};
};
This DT config is not yet configuring everything: when the netdev
default trigger is assigned the hw acceleration callbacks are
not called, and there is no way to set the netdev sub-trigger
type (such as link_1000) from the device tree, such as if you want
a gigabit link indicator. This has to be done from userspace at
this point.
We add LED operations to all switches in the 6352 family:
6172, 6176, 6240 and 6352.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241001-mv88e6xxx-leds-v4-1-cc11c4f49b18@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit introduced an unexpected regression in the sja1105
driver. Packets from VLAN-unaware bridge ports get received correctly,
but the protocol stack can't seem to decode them properly.
For ds->untag_bridge_pvid users (thus also sja1105), the blamed commit
did introduce a functional change: dsa_switch_rcv() used to call
dsa_untag_bridge_pvid(), which looked like this:
err = br_vlan_get_proto(br, &proto);
if (err)
return skb;
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb) && skb->protocol == htons(proto)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
and now it calls dsa_software_vlan_untag() which has just this:
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
thus lacks any skb->protocol == bridge VLAN protocol check. That check
is deferred until a later check for skb->vlan_proto (in the hwaccel area).
The new code is problematic because, for VLAN-untagged packets,
skb_vlan_untag() blindly takes the 4 bytes starting with the EtherType
and turns them into a hwaccel VLAN tag. This is what breaks the protocol
stack.
It would be tempting to "make it work as before" and only call
skb_vlan_untag() for those packets with the skb->protocol actually
representing a VLAN.
But the premise of the newly introduced dsa_software_vlan_untag() core
function is not wrong. Drivers set ds->untag_bridge_pvid or
ds->untag_vlan_aware_bridge_pvid presumably because they send all
traffic to the CPU reception path as VLAN-tagged. So why should we spend
any additional CPU cycles assuming that the packet may be VLAN-untagged?
And why does the sja1105 driver opt into ds->untag_bridge_pvid if it
doesn't always deliver packets to the CPU as VLAN-tagged?
The answer to the latter question is indeed more interesting: it doesn't
need to. This got done in commit 884be12f85 ("net: dsa: sja1105: add
support for imprecise RX"), because I thought it would be needed, but I
didn't realize that it doesn't actually make a difference.
As explained in the commit message of the blamed patch, ds->untag_bridge_pvid
only makes a difference in the VLAN-untagged receive path of a bridge port.
However, in that operating mode, tag_sja1105.c makes use of VLAN tags
with the ETH_P_SJA1105 TPID, and it decodes and consumes these VLAN tags
as if they were DSA tags (aka tag_8021q operation). Even if commit
884be12f85 ("net: dsa: sja1105: add support for imprecise RX") added
this logic in sja1105_bridge_vlan_add():
/* Always install bridge VLANs as egress-tagged on the CPU port. */
if (dsa_is_cpu_port(ds, port))
flags = 0;
that was for _bridge_ VLANs, which are _not_ committed to hardware
in VLAN-unaware mode (aka the mode where ds->untag_bridge_pvid does
anything at all). Even prior to that change, the tag_8021q VLANs
were always installed as egress-tagged on the CPU port, see
dsa_switch_tag_8021q_vlan_add():
u16 flags = 0; // egress-tagged, non-PVID
if (dsa_port_is_user(dp))
flags |= BRIDGE_VLAN_INFO_UNTAGGED |
BRIDGE_VLAN_INFO_PVID;
err = dsa_port_do_tag_8021q_vlan_add(dp, info->vid,
flags);
if (err)
return err;
Whether the sja1105 driver needs the new flag, ds->untag_vlan_aware_bridge_pvid,
rather than ds->untag_bridge_pvid, is a separate discussion. To fix the
current bug in VLAN-unaware bridge mode, I would argue that the sja1105
driver should not request something it doesn't need, rather than
complicating the core DSA helper. Whereas before the blamed commit, this
setting was harmless, now it has caused breakage.
Fixes: 93e4649efa ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241001140206.50933-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use xpcs_create_pcs_mdiodev() to create the XPCS instance, storing
and using the phylink_pcs pointer internally, rather than dw_xpcs.
Use xpcs_destroy_pcs() to destroy the XPCS instance when we've
finished with it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMk-005ZIj-R3@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call the PCS operations through the ops structure, which avoids needing
to export xpcs internal functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMf-005ZId-Mx@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The static configuration reload saves the port speed in the static
configuration tables by first converting it from the internal
respresentation to the SPEED_xxx ethtool representation, and then
converts it back to restore the setting. This is because
sja1105_adjust_port_config() takes the speed as SPEED_xxx.
However, this is unnecessarily complex. If we split
sja1105_adjust_port_config() up, we can simply save and restore the
mac[port].speed member in the static configuration tables.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMa-005ZIX-If@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Cross-merge networking fixes after downstream PR.
No conflicts (sort of) and no adjacent changes.
This merge reverts commit b3c9e65eb2 ("net: hsr: remove seqnr_lock")
from net, as it was superseded by
commit 430d67bdcb ("net: hsr: Use the seqnr lock for frames received via interlink port.")
in net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TAS module could not be configured when it's running in pending
status. We need disable the module and configure it again. However, the
pending status is not cleared after the module disabled. TC taprio set
will always return busy even it's disabled.
For example, a user uses tc-taprio to configure Qbv and a future
basetime. The TAS module will run in a pending status. There is no way
to reconfigure Qbv, it always returns busy.
Actually the TAS module can be reconfigured when it's disabled. So it
doesn't need to check the pending status if the TAS module is disabled.
After the patch, user can delete the tc taprio configuration to disable
Qbv and reconfigure it again.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Link: https://patch.msgid.link/20240906093550.29985-1-xiaoliang.yang_1@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace ksz8830 with ksz88x3 for CHIP_ID definition and other
strings. This due to KSZ8830 not being an actual switch but the Chip
ID shared among KSZ8863/8873 switches, impossible to differentiate
from their Chip ID or Revision ID registers.
Now all KSZ*_CHIP_ID macros refer to actual, existing switches which
removes confusion.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove macros that are already defined at more appropriate places.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first KSZ8 series implementation was done for a KSZ8795 device but
since several other KSZ8 devices have been added. Rename these files
to adhere to the ksz8 naming convention as already used in most
functions and the existing ksz8.h; add an explanatory note.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the __counted_by compiler attribute to the flexible array member
entries to improve access bounds-checking via CONFIG_UBSAN_BOUNDS and
CONFIG_FORTIFY_SOURCE.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://patch.msgid.link/20240904014956.2035117-1-lihongbo22@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Avoids the need for manual cleanup of_node_put() in early exits
from the loop by using for_each_available_child_of_node_scoped().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Avoid need to manually handle of_node_put() by using
for_each_child_of_node_scoped(), which can simplfy code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This commit introduces implementations of three functions:
.port_fdb_dump
.port_fdb_add
.port_fdb_del
The FDB database organization is the same as in other old Vitesse chips:
It has 2048 rows and 4 columns (buckets). The row index is calculated by
the hash function 'vsc73xx_calc_hash' and the FDB entry must be placed
exactly into row[hash]. The chip selects the bucket number by itself.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://patch.msgid.link/20240827123938.582789-1-paweldembicki@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Using dev_err_cast_probe() to simplify the code.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Link: https://patch.msgid.link/20240828121805.3696631-1-lihongbo22@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GPIOF_DIR_* definitions are legacy and subject to remove.
Taking this into account, remove stale comment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240827171005.2301845-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KSZ8895/KSZ8864 is a switch family between KSZ8863/73 and KSZ8795, so it
shares some registers and functions in those switches already
implemented in the KSZ DSA driver.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Tested-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt.h
c948c0973d ("bnxt_en: Don't clear ntuple filters and rss contexts during ethtool ops")
f2878cdeb7 ("bnxt_en: Add support to call FW to update a VNIC")
Link: https://patch.msgid.link/20240822210125.1542769-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240820075047.681223-1-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240820074805.680674-1-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If an ATU violation was caused by a CPU Load operation, the SPID could
be larger than DSA_MAX_PORTS (the size of mv88e6xxx_chip.ports[] array).
Fixes: 75c05a74e7 ("net: dsa: mv88e6xxx: Fix counting of ATU violations")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240819235251.1331763-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing the port_hwtstamp_set operation, ptp_schedule_worker()
will be called if hardware timestamoing is enabled on any of the ports.
When using multiple ports for PTP, port_hwtstamp_set is executed for
each port. When called for the first time ptp_schedule_worker() returns
0. On subsequent calls it returns 1, indicating the worker is already
scheduled. Currently the ksz driver treats 1 as an error and fails to
complete the port_hwtstamp_set operation, thus leaving the timestamping
configuration for those ports unchanged.
This patch fixes this by ignoring the ptp_schedule_worker() return
value.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/7aae307a-35ca-4209-a850-7b2749d40f90@martin-whitaker.me.uk
Fixes: bb01ad3057 ("net: dsa: microchip: ptp: manipulating absolute time using ptp hw clock")
Signed-off-by: Martin Whitaker <foss@martin-whitaker.me.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240817094141.3332-1-foss@martin-whitaker.me.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ87xx switches have 32 static MAC address table entries and not
8. This fixes -ENOSPC non-critical errors from ksz8_add_sta_mac when
configured as a bridge.
Add a new ksz87xx_dev_ops structure to be able to use the
ksz_r_mib_stat64 pointer for this family; this corrects a wrong
mib->counters cast to ksz88xx_stats_raw. This fixes iproute2
statistics. Rename ksz8_dev_ops structure to ksz88x3_dev_ops, in line
with ksz_is_* naming conventions from ksz_common.h.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-6-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add WoL support for KSZ87xx family of switches. This code was tested
with a KSZ8794 chip.
Implement ksz_common usage of the new device-tree property
'microchip,pme-active-high'.
Make use of the now generalized ksz_common WoL functions, adding an
additional interrupt register write for KSZ87xx. Add helper functions
to convert from PME (port) read/writes to indirect register
read/writes in the dedicated ksz8795 sources. Add initial
configuration during (port) setup as per KSZ9477.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-5-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Generalize KSZ9477 WoL functions at ksz_common. Move dedicated registers
and generic masks to existing structures & defines for that purpose.
Introduction of PME (port) read/write helper functions, which happen
to be the generic read/write for KSZ9477 but not for the incoming
KSZ87xx patch.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-4-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move KSZ9477 WoL functions to ksz_common, in preparation for adding
KSZ87xx family support.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-3-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a major design bug with ocelot-8021q, which is that it expects
more of the hardware than the hardware can actually do. The short
summary of the issue is that when a port is under a VLAN-aware bridge
and we use this tagging protocol, VLAN upper interfaces of this port do
not see RX traffic.
We use VCAP ES0 (egress rewriter) rules towards the tag_8021q CPU port
to encapsulate packets with an outer tag, later stripped by software,
that depends on the source user port. We do this so that packets can be
identified in ocelot_rcv(). To be precise, we create rules with
push_outer_tag = OCELOT_ES0_TAG and push_inner_tag = 0.
With this configuration, we expect the switch to keep the inner tag
configuration as found in the packet (if it was untagged on user port
ingress, keep it untagged, otherwise preserve the VLAN tag unmodified
as the inner tag towards the tag_8021q CPU port). But this is not what
happens.
Instead, table "Tagging Combinations" from the user manual suggests
that when the ES0 action is "PUSH_OUTER_TAG=1 and PUSH_INNER_TAG=0",
there will be "no inner tag". Experimentation further clarifies what
this means.
It appears that this "inner tag" which is not pushed into the packet on
its egress towards the CPU is none other than the classified VLAN.
When the ingress user port is standalone or under a VLAN-unaware bridge,
the classified VLAN is a discardable quantity: it is a fixed value - the
result of ocelot_vlan_unaware_pvid()'s configuration, and actually
independent of the VID from any 802.1Q header that may be in the frame.
It is actually preferable to discard the "inner tag" in this case.
The problem is when the ingress port is under a VLAN-aware bridge.
Then, the classified VLAN is taken from the frame's 802.1Q header, with
a fallback on the bridge port's PVID. It would be very good to not
discard the "inner tag" here, because if we do, we break communication
with any 8021q VLAN uppers that the port might have. These have a
processing path outside the bridge.
There seems to be nothing else we can do except to change the
configuration for VCAP ES0 rules, to actually push the inner VLAN into
the frame. There are 2 options for that, first is to push a fixed value
specified in the rule, and second is to push a fixed value, plus
(aka arithmetic +) the classified VLAN. We choose the second option,
and we select that fixed value as 0. Thus, what is pushed in the inner
tag is just the classified VLAN.
From there, we need to perform software untagging, in the receive path,
of stuff that was untagged on the wire.
Fixes: 7c83a7c539 ("net: dsa: add a second tagger for Ocelot switches based on tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained by Horatiu Vultur in commit 603ead9658 ("net: sparx5: Add
spinlock for frame transmission from CPU") which is for a similar
hardware design, multiple CPUs can simultaneously perform injection
or extraction. There are only 2 register groups for injection and 2
for extraction, and the driver only uses one of each. So we'd better
serialize access using spin locks, otherwise frame corruption is
possible.
Note that unlike in sparx5, FDMA in ocelot does not have this issue
because struct ocelot_fdma_tx_ring already contains an xmit_lock.
I guess this is mostly a problem for NXP LS1028A, as that is dual core.
I don't think VSC7514 is. So I'm blaming the commit where LS1028A (aka
the felix DSA driver) started using register-based packet injection and
extraction.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the URL in a single line for easier copy-pasting.
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240812124346.597702-1-enguerrand.de-ribaucourt@savoirfairelinux.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Resetting the VSC73xx PHY was problematic because the MDIO bus, without
a busy check, read and wrote incorrect register values.
My investigation indicates that resetting the PHY only triggers changes
in configuration. However, improper register values written earlier
were only exposed after a soft reset.
The reset itself wasn't the issue; rather, the problem stemmed from
incorrect read and write operations.
A 'soft_reset' can now proceed normally. There are no reasons to keep
the VSC73xx from being reset.
This commit removes the reset blockade in the 'vsc73xx_phy_write'
function.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC73xx has a busy flag used during MDIO operations. It is raised
when MDIO read/write operations are in progress. Without it, PHYs are
misconfigured and bus operations do not work as expected.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the 'vsc73xx_phy_write' function, the register value is missing,
and the phy write operation always sends zeros.
This commit passes the value variable into the proper register.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the datasheet description ("Port Mode Procedure" in 5.6.2),
the VSC73XX_MAC_CFG_WEXC_DIS bit is configured only for half duplex mode.
The WEXC_DIS bit is responsible for MAC behavior after an excessive
collision. Let's set it as described in the datasheet.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to respect the 80 columns limit, split the half-duplex
monitoring function in two.
This is just a styling change, no functional change.
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit changes magic numbers in phy operations.
Some shifted registers was replaced with bitfield macros.
No functional changes done.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2_mdio_register() calls of_phy_find_device() and then
phy_device_remove() in a loop to remove existing PHY devices.
of_phy_find_device() eventually calls bus_find_device(), which calls
get_device() on the returned struct device * to increment the refcount.
The current implementation does not decrement the refcount, which causes
memory leak.
This commit adds the missing phy_device_free() call to decrement the
refcount via put_device() to balance the refcount.
Fixes: 771089c2a4 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240806011327.3817861-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The wol variable in ksz_port_set_mac_address() is declared with random
data, but the code in ksz_get_wol call may not be executed so the
WAKE_MAGIC check may be invalid resulting in an error message when
setting a MAC address after starting the DSA driver.
Fixes: 3b454b6390 ("net: dsa: microchip: ksz9477: Add Wake on Magic Packet support")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240805235200.24982-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce support for the DSA built-in switch available on the EN7581
development board. EN7581 support is similar to MT7988 one except
it requires to set MT7530_FORCE_MODE bit in MT753X_PMCR_P register
for on cpu port.
Tested-by: Benjamin Larsson <benjamin.larsson@genexis.eu>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the datasheet, the VSC73xx family's maximum internal MDIO bus
speed is 20 MHz. It also allows disabling the preamble.
This commit sets the MDIO clock prescaler to the minimum value and
disables the preamble to speed up MDIO operations.
It doesn't affect the external bus because it's configured in a different
subblock.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240731203455.580262-1-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch switches hardcoded RGMII transmit/receive delay to
a configurable value. Delay values are taken from the properties of
the CPU port: 'tx-internal-delay-ps' and 'rx-internal-delay-ps'.
The default value is configured to 2.0 ns to maintain backward
compatibility with existing code.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom switches supported by the b53 driver use a chip-wide jumbo frame
configuration. In the commit referenced with the Fixes tag, the setting
is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient chip-wide maximum frame size for the CPU port.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports. This aligns the driver
to the behavior of other switch drivers.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Marvell chips not supporting per-port jumbo frame size configurations use
a chip-wide frame size configuration. In the commit referenced with the
Fixes tag, the setting is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient maximum frame size for the CPU port. Specifically, sending
full-size frames from the CPU port on a MV88E6097 having a user port MTU
of 1500 bytes results in dropped frames.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch implements .port_pre_bridge_flags() and .port_bridge_flags(),
which are required for properly treating the BR_LEARNING flag. Also,
.port_stp_state_set() is tweaked and now disables learning for standalone
ports.
Disabling learning for standalone ports is required to avoid situations
where one port sees traffic originating from another, which could cause
packet drops.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-13-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds bridge support for the vsc73xx driver.
The vsc73xx requires minimal operations and ithe generic
dsa_tag_8021q_bridge_* API is sufficient.
The forwarding matrix is managed by vsc73xx_port_stp_state_set() ->
vsc73xx_refresh_fwd_map()i routine, which is called immediately after
.port_bridge_join() and .port_bridge_leave().
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-12-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'dsa_tag_8021q_bridge_join' could be used as a generic implementation
of the 'ds->ops->port_bridge_join()' function. However, it is necessary
to synchronize their arguments.
This patch also moves the 'tx_fwd_offload' flag configuration line into
'dsa_tag_8021q_bridge_join' body. Currently, every (sja1105) driver sets
it, and the future vsc73xx implementation will also need it for
simplification.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-11-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Max number of bridges in tag8021q implementation is strictly limited
by VBID size: 3 bits. But zero is reserved and only 7 values can be used.
This patch adds define which describe maximum possible value.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-10-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is a simple implementation of 802.1q tagging in the vsc73xx
driver. Currently, devices with DSA_TAG_PROTO_NONE are not functional.
The VSC73XX family doesn't provide any tag support for external Ethernet
ports.
The only option available is VLAN-based tagging, which requires constant
hardware VLAN filtering. While the VSC73XX family supports provider
bridging, it only supports QinQ without full implementation of 802.1AD.
This means it only allows the doubled 0x8100 TPID.
In the simple port mode, QinQ is enabled to preserve forwarding of
VLAN-tagged frames.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-9-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch implements VLAN filtering for the vsc73xx driver.
After starting VLAN filtering, the switch is reconfigured from QinQ to
a simple VLAN aware mode. This is required because VSC73XX chips do not
support inner VLAN tag filtering.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-3-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This isn't a fully functional implementation of 802.1D, but
port_stp_state_set is required for a future tag8021q operations.
This implementation handles properly all states, but vsc73xx doesn't
forward STP packets.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://patch.msgid.link/20240713211620.1125910-2-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/act_ct.c
26488172b0 ("net/sched: Fix UAF when resolving a clash")
3abbd7ed8b ("act_ct: prepare for stolen verdict coming from conntrack and nat engine")
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set proper MAC capabilities for port 4 on LAN9371 and LAN9372 switches with
integrated 100BaseTX PHY. And introduce the is_lan937x_tx_phy() function to
reuse it where applicable.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`ar9331_sw_bus` is not modified and can be declared as const to
move its data to a read-only section.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240703-net-const-regmap-v1-4-ff4aeceda02c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
`qca8k_regmap_config` is not modified and can be declared as const to
move its data to a read-only section.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240703-net-const-regmap-v1-1-ff4aeceda02c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'phy' parameter supplied to lan9303_phy_read/_write was sometimes a
DSA port number and sometimes a PHY address. This isn't a problem as
long as they are equal. But if the external phy_addr_sel_strap pin is
wired to 'high', the PHY addresses change from 0-1-2 to 1-2-3 (CPU,
slave0, slave1). In this case, lan9303_phy_read/_write must translate
between DSA port numbers and the corresponding PHY address.
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240703145718.19951-1-ceggers@arri.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce error handling for lan937x_cfg function calls in lan937x_setup.
This change ensures that if any lan937x_cfg or ksz_rmw32 calls fails, the
function will return the appropriate error code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240703083820.3152100-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As described by the microchip article "LAN937X - The required
configuration for the external MAC port to operate at RGMII-to-RGMII
1Gbps link speed." [1]:
"When VPHY is enabled, the auto-negotiation process following IEEE 802.3
standard will be triggered and will result in RGMII-to-RGMII signal
failure on the interface because VPHY will try to poll the PHY status
that is not available in the scenario of RGMII-to-RGMII connection
(normally the link partner is usually an external processor).
Note that when VPHY fails on accessing PHY registers, it will fall back
to 100Mbps speed, it indicates disabling VPHY is optional if you only
need the port to link at 100Mbps speed.
Again, VPHY must and can only be disabled by writing VPHY_DISABLE bit in
the register below as there is no strapping pin for the control."
This patch was tested on LAN9372, so far it seems to not to affect VPHY
based clock crossing optimization for the ports with integrated PHYs.
[1]: https://microchip.my.site.com/s/article/LAN937X-The-required-configuration-for-the-external-MAC-port-to-operate-at-RGMII-to-RGMII-1Gbps-link-speed
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver do not support in-band mode and in case of CPU<->Switch
link, this mode is not working any way. So, disable it otherwise ingress
path of the switch MAC will stay disabled.
Note: lan9372 manual do not document 0xN301 BIT(2) for the RGMII mode
and recommend[1] to disable in-band link status update for the RGMII RX
path by clearing 0xN302 BIT(0). But, 0xN301 BIT(2) seems to work too, so
keep it unified with other KSZ switches.
[1] https://microchip.my.site.com/s/article/LAN937X-The-required-configuration-for-the-external-MAC-port-to-operate-at-RGMII-to-RGMII-1Gbps-link-speed
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the LAN9371 and LAN9372, the 4th internal PHY is a 100BaseTX PHY
instead of a 100BaseT1 PHY. The 100BaseTX PHYs have a different base
register offset.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
e3f02f32a0 ("ionic: fix kernel panic due to multi-buffer handling")
d9c0420999 ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For mlxsw
Reviewed-by: Kory Maincent <Kory.maincent@bootlin.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au> # for mctp-i2c
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20240625083853.2205977-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch global port interrupt mask, REG_SW_PORT_INT_MASK__4, is
defined as 0x001C in ksz9477_reg.h. The designers used 32-bit value in
anticipation for increase of port count in future product but currently
the maximum port count is 7 and the effective value is 0x7F in register
0x001F. Each port has its own interrupt mask and is defined as 0x#01F.
It uses only 4 bits for different interrupts.
The developer who implemented the current interrupt mechanism in the
switch driver noticed there are similarities between the mechanism to
mask port interrupts in global interrupt and individual interrupts in
each port and so used the same code to handle these interrupts. He
updated the code to use the new macro REG_SW_PORT_INT_MASK__1 which is
defined as 0x1F in ksz_common.h but he forgot to update the 32-bit write
to 8-bit as now the mask registers are 0x1F and 0x#01F.
In addition all KSZ switches other than the KSZ9897/KSZ9893 and LAN937X
families use only 8-bit access and so this common code will eventually
be changed to accommodate them.
Fixes: e1add7dd61 ("net: dsa: microchip: use common irq routines for girq and pirq")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://lore.kernel.org/r/1719009262-2948-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The errata DS80000754 recommends monitoring potential faults in
half-duplex mode for the KSZ9477 family.
half-duplex is not very common so I just added a critical message
when the fault conditions are detected. The switch can be expected
to be unable to communicate anymore in these states and a software
reset of the switch would be required which I did not implement.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errata DS80000758 states that carrier sense back pressure mode can cause
link down issues in 100BASE-TX half duplex mode. The datasheet also
recommends to always use the collision based back pressure mode.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Woojung Huh <Woojung.huh@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a pair of ports from the port matrix when both ports have the
isolated flag set.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the logic in qca8k_port_bridge_join() and qca8k_port_bridge_leave()
is the same. Refactor to reduce duplication and prepare for reusing the
code for implementing bridge port isolation.
dsa_port_offloads_bridge_dev() is used instead of
dsa_port_offloads_bridge(), passing the bridge in as a struct netdevice *,
as we won't have a struct dsa_bridge in qca8k_port_bridge_flags().
The error handling is changed slightly in the bridge leave case,
returning early and emitting an error message when a regmap access fails.
This shouldn't matter in practice, as there isn't much we can do if
communication with the switch breaks down in the middle of reconfiguration.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k_port_bridge_join() set QCA8K_PORT_LOOKUP_CTRL() for i == port twice,
once in the loop handling all other port's masks, and finally at the end
with the accumulated port_mask.
The first time it would incorrectly set the port's own bit in the mask,
only to correct the mistake a moment later. qca8k_port_bridge_leave() had
the same issue, but here the regmap_clear_bits() was a no-op rather than
setting an unintended value.
Remove the duplicate assignment by skipping the whole loop iteration for
i == port. The unintended bit setting doesn't seem to have any negative
effects (even when not reverted right away), so the change is submitted
as a simple cleanup rather than a fix.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 allows HSR in-HW offloading for any of two selected ports.
This patch adds check if one tries to use more than two ports with
HSR offloading enabled.
The problem is with RedBox configuration (HSR-SAN) - when configuring:
ip link add name hsr0 type hsr slave1 lan1 slave2 lan2 interlink lan3 \
supervision 45 version 1
The lan1 (port0) and lan2 (port1) are correctly configured as ports, which
can use HSR offloading on ksz9477.
However, when we do already have two bits set in hsr_ports, we need to
return (-ENOTSUPP), so the interlink port (lan3) would be used with
SW based HSR RedBox support.
Otherwise, I do see some strange network behavior, as some HSR frames are
visible on non-HSR network and vice versa.
This causes the switch connected to interlink port (lan3) to drop frames
and no communication is possible.
Moreover, conceptually - the interlink (i.e. HSR-SAN port - lan3/port2)
shall be only supported in software as it is also possible to use ksz9477
with only SW based HSR (i.e. port0/1 -> hsr0 with offloading, port2 ->
HSR-SAN/interlink, port4/5 -> hsr1 with SW based HSR).
Fixes: 5055cccfc2 ("net: hsr: Provide RedBox support (HSR-SAN)")
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The very first flush in any port will flush all learned addresses in all
ports. This can be observed by unplugging the cable from one port while
additional ports are connected and dumping the fdb entries.
This problem is caused by the initially wrong value programmed to the
REG_SW_LUE_CTRL_1 register. Setting SW_FLUSH_STP_TABLE and
SW_FLUSH_MSTP_TABLE bits does not have an immediate effect. It is when
ksz9477_flush_dyn_mac_table() is called then the SW_FLUSH_STP_TABLE bit
takes effect and flushes all learned entries. After that call both bits
are reset and so the next port flush will not cause such problem again.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/1718756202-2731-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove a pair of ports from the port matrix when both ports have the
isolated flag set.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As preparation for implementing bridge port isolation, move the logic to
add and remove bits in the port matrix into a new helper
mt7530_update_port_member(), which is called from
mt7530_port_bridge_join() and mt7530_port_bridge_leave().
Another part of the preparation is using dsa_port_offloads_bridge_dev()
instead of dsa_port_offloads_bridge() to check for bridge membership, as
we don't have a struct dsa_bridge in mt7530_port_bridge_flags().
The port matrix setting is slightly streamlined, now always first setting
the mt7530_port's pm field and then writing the port matrix from that
field into the hardware register, instead of duplicating the bit
manipulation for both the struct field and the register.
mt7530_port_bridge_join() was previously using |= to update the port
matrix with the port bitmap, which was unnecessary, as pm would only
have the CPU port set before joining a bridge; a simple assignment can
be used for both joining and leaving (and will also work when individual
bits are added/removed in port_bitmap with regard to the previous port
matrix, which is what happens with port isolation).
No functional change intended.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print that no FID is found for bridge %s instead of the incorrect
message that the port is not part of a bridge.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-13-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the comments in gswip_port_vlan_filtering() so it's clear that
there are two separate cases, one for "tag based VLAN" and another one
for "port based VLAN".
Suggested-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-12-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The port validation in gswip_add_single_port_br() is superfluous and
can be omitted.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240611135434.3180973-11-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Only bits [5:0] in mac_bridge.key[3] are reserved for the FID.
Also, for dynamic (learned) entries, bits [7:4] in mac_bridge.val[0]
represents the port.
Introduce new macros GSWIP_TABLE_MAC_BRIDGE_KEY3_FID and
GSWIP_TABLE_MAC_BRIDGE_VAL0_PORT macro and use it throughout the driver.
Also rename and update GSWIP_TABLE_MAC_BRIDGE_VAL1_STATIC to use the
BIT() macro. This makes the driver code easier to understand.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240611135434.3180973-10-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The addr variable in gswip_port_fdb_dump() stores a mac address. Use
ETH_ALEN to make this consistent across other drivers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-9-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make the check for the CPU port in gswip_port_change_mtu() consistent
with other areas of the driver by using dsa_is_cpu_port().
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-8-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before commit 74be4babe7 ("net: dsa: do not enable or disable non user
ports"), gswip_port_enable/disable() were also executed for the cpu port
in gswip_setup() which disabled the cpu port during initialization.
Let's restore this by removing the dsa_is_user_port checks. Also, let's
clean up the gswip_port_enable() function so that we only have to check
for the cpu port once. The operation reordering done here is safe.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240611135434.3180973-7-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We don't need to manually call gswip_port_enable() from within
gswip_setup() for the CPU port. DSA does this automatically for us.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-6-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_err_probe() can be used to simplify the existing code. Also it means
we get rid of the following warning which is seen whenever the PMAC
(Ethernet controller which connects to GSWIP's CPU port) has not been
probed yet:
gswip 1e108000.switch: dsa switch register failed: -517
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-5-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some dev_err are missing the terminating \n. Let's add that.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240611135434.3180973-4-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the CPU port to gswip_xrx200_phylink_get_caps() and
gswip_xrx300_phylink_get_caps(). It connects through a SoC-internal bus,
so the only allowed phy-mode is PHY_INTERFACE_MODE_INTERNAL.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20240611135434.3180973-3-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kernel.h is included solely for some other existing headers.
Include them directly and get rid of kernel.h.
While at it, sort headers alphabetically for easier maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation for device_get_named_child_node() mentions this
important point:
"
The caller is responsible for calling fwnode_handle_put() on the
returned fwnode pointer.
"
Add fwnode_handle_put() to avoid leaked references.
Fixes: 1e264f9d29 ("net: dsa: qca8k: add LEDs basic support")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the common felix_register_switch() from the umbrella driver
is the only entity that accesses these data structures, we can remove
them from the list of the exported symbols.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init code, which could be
made common [1].
[1]: https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Here, we take the following common steps:
- "felix" and "ds" structure allocation
- "felix", "ocelot" and "ds" basic structure initialization
- dsa_register_switch() call
and we make a common function out of them.
For every driver except felix_vsc9959, this is also the entire probing
procedure. For felix_vsc9959, we also need to do some PCI-specific
stuff, which can easily be reordered to be done before, and unwound on
failure.
We also have to convert the bus-specific platform_set_drvdata() and
pci_set_drvdata() calls into dev_set_drvdata(). But this should have no
impact on the behavior.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King points out that seville_vsc9953 populates
felix->info->num_tx_queues = 8, but this doesn't make it all the way
into ds->num_tx_queues (which is how the user interface netdev queues
get allocated) [1].
[1]: https://lore.kernel.org/all/20240415160150.yejcazpjqvn7vhxu@skbuf/
When num_tx_queues=0 for seville, this is implicitly converted to 1 by
dsa_user_create(), and this is good enough for basic operation for a
switch port. The tc qdisc offload layer works with netdev TX queues,
so for QoS offload we need to pretend we have multiple TX queues. The
VSC9953, like ocelot_ext, doesn't export QoS offload, so it doesn't
really matter. But we can definitely set num_tx_queues=8 for all
switches.
The felix->info->num_tx_queues construct itself seems unnecessary.
It was introduced by commit de143c0e27 ("net: dsa: felix: Configure
Time-Aware Scheduler via taprio offload") at a time when vsc9959
(LS1028A) was the only switch supported by the driver.
8 traffic classes, and 1 queue per traffic class, is a common
architectural feature of all switches in the family. So they could
all just set OCELOT_NUM_TC and be fine.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current placement of devm_request_threaded_irq() is inconvenient.
It is between the allocation of the "felix" structure and
dsa_register_switch(), both of which we'd like to refactor into a
function that's common for all switches. But the IRQ is specific to
felix_vsc9959.
A closer inspection of the felix_irq_handler() code suggests that
it does things that depend on the data structures having been fully
initialized. For example, ocelot_get_txtstamp() takes
&port->tx_skbs.lock, which has only been initialized in
ocelot_init_port() which has not run yet.
It is not one of those IRQF_SHARED IRQs, so CONFIG_DEBUG_SHIRQ_FIXME
shouldn't apply here, and thus, it doesn't really matter, because in
practice, the IRQ will not be triggered so early. Nonetheless, it is a
good practice for the driver to be prepared for it to fire as soon as it
is requested.
Create a new felix->info method for running custom code for vsc9959 from
within felix_setup(), and move the request_irq() call there. The
ocelot_ext should have an IRQ as well, so this should be a step in the
right direction for that model (VSC7512) as well.
Some minor changes are made while moving the code. Casts from void *
aren't necessary, so drop them, and rename felix_irq_handler() to the
more specific vsc9959_irq_handler().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init and teardown code,
which could be made common [1]. The teardown code could even be
simplified away if we made use of devres, something which is used here
and there in the felix driver, just not very consistently.
[1] https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Prepare the ground in the felix_vsc9959 driver, by allocating the data
structures using devres and deleting the kfree() calls. This also
deletes the "Failed to allocate ..." message, since memory allocation
errors are extremely loud anyway, and it's hard to miss them.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6fffbc7ae1 ("PCI: Honor firmware's device disabled
status"), PCI device drivers with OF bindings no longer need this check.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init and teardown code,
which could be made common [1]. The teardown code could even be
simplified away if we made use of devres, something which is used here
and there in the felix driver, just not very consistently.
[1] https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Prepare the ground in the seville_vsc9953 driver, by allocating the data
structures using devres and deleting the kfree() calls. This also
deletes the "Failed to allocate ..." message, since memory allocation
errors are extremely loud anyway, and it's hard to miss them.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init and teardown code,
which could be made common [1]. The teardown code could even be
simplified away if we made use of devres, something which is used here
and there in the felix driver, just not very consistently.
[1] https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Prepare the ground in the ocelot_ext driver, by allocating the data
structures using devres and deleting the kfree() calls. This also
deletes the "Failed to allocate ..." message, since memory allocation
errors are extremely loud anyway, and it's hard to miss them.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/ti/icssg/icssg_classifier.c
abd5576b9c ("net: ti: icssg-prueth: Add support for ICSSG switch firmware")
56a5cf538c ("net: ti: icssg-prueth: Fix start counter for ft1 filter")
https://lore.kernel.org/all/20240531123822.3bb7eadf@canb.auug.org.au/
No other adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver should return RMII interface when XMII is running in RMII mode.
Fixes: 0ab7f6bf16 ("net: dsa: microchip: ksz9477: use common xmii function")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Acked-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1716932066-3342-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert felix to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/E1sByYA-00EM0y-Jn@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both LAN9303 and LAN9354 have internal PHYs on both external ports.
Therefore a configuration without SMSC PHY support is non-practical at
least and leads to:
LAN9303_MDIO 8000f00.mdio:00: Found LAN9303 rev. 1
mdio_bus 8000f00.mdio:00: deferred probe pending: (reason unknown)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240528073147.3604083-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
Adjust the initialization sequence of KSZ88x3 switches to enable
802.1p priority control on Port 2 before configuring Port 1. This
change ensures the apptrust functionality on Port 1 operates
correctly, as it depends on the priority settings of Port 2. The
prior initialization sequence incorrectly configured Port 1 first,
which could lead to functional discrepancies.
Fixes: a1ea57710c ("net: dsa: microchip: dcb: add special handling for KSZ88X3 family")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240517050121.2174412-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before DCB support, the KSZ driver had only PCP as source of packet
priority values. To avoid regressions, make PCP only as default value.
User will need enable DSCP support manually.
This patch do not affect other KSZ8 related quirks. User will still be
warned by setting not support configurations for the port 2.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All other functions are commented. Add missing comments to following
functions:
ksz_set_global_dscp_entry()
ksz_port_add_dscp_prio()
ksz_port_del_dscp_prio()
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPV is added and used term in 802.1Qci PSFP and merged into 802.1Q (from
802.1Q-2018) for another functions.
Even it does similar operation holding temporal priority value
internally (as it is named), because KSZ datasheet doesn't use the term
of IPV (Internal Priority Value) and avoiding any confusion later when
PSFP is in the Linux world, it is better to rename IPV to IPM (Internal
Priority Mapping).
In addition, LAN937x documentation already use IPV for 802.1Qci PSFP
related functionality.
Suggested-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
35d92abfba ("net: hns3: fix kernel crash when devlink reload during initialization")
2a1a1a7b5f ("net: hns3: add command queue trace for hns3")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the mv88e6320 and 6321 switch family, port 0/1 are serdes only ports.
Modified the mv88e6352_get_port4_serdes_cmode function to pass a port
number since the register set of the 6352 is equal on the 6320/21.
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240508072944.54880-3-steffen@innosonix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As of commit de5c9bf40c ("net: phylink: require supported_interfaces to
be filled")
Marvell 88e6320/21 switches fail to be probed:
...
mv88e6085 30be0000.ethernet-1:00: phylink: error: empty supported_interfaces
error creating PHYLINK: -22
...
The problem stems from the use of mv88e6185_phylink_get_caps() to get
the device capabilities.
Since there are serdes only ports 0/1 included, create a new dedicated
phylink_get_caps for the 6320 and 6321 to properly support their
set of capabilities.
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240508072944.54880-2-steffen@innosonix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Microchip KSZ and LAN variants do not have per port DSCP priority
configuration. Instead there is a global DSCP mapping table.
This patch provides write access to this global DSCP map. In case entry
is "deleted", we map corresponding DSCP entry to a best effort prio,
which is expected to be the default priority for all untagged traffic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
802.1P (PCP) and DiffServ (DSCP) are handled now by DCB code. Let it do
all needed initial configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Init priority to queue mapping in the way as it shown in IEEE 802.1Q
mapping example.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tested ETS support on KSZ9893, so it should work other KSZ989X
variants too, which was till not listed as support.
With this change we now officially not support only ksz8 family of
chips.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni